Optoma 3D-RF Glasses Bedienungsanleitung
Optoma
Projektorzubehör
3D-RF Glasses
Lies die bedienungsanleitung für Optoma 3D-RF Glasses (24 Seiten) kostenlos online; sie gehört zur Kategorie Projektorzubehör. Dieses Handbuch wurde von 21 Personen als hilfreich bewertet und erhielt im Schnitt 3.8 Sterne aus 11 Bewertungen. Hast du eine Frage zu Optoma 3D-RF Glasses oder möchtest du andere Nutzer dieses Produkts befragen? Stelle eine Frage
Seite 1/24
Copyright 2011 Bit Cauldron Corporaon Page 1 of 24
User’s Manual – Optoma - System Optoma - Glasses and Optoma -3D RF : 3D RF 3D
RF Emier
Contains Patent Pending soware and technology from Bit Cauldron
Conent les logiels de brevet en instance et la technologie de la compagnie Bit Cauldron
Optoma - Emier Manual 3D RF
The Optoma - Emier connects Optoma 3D-XL converter box to the Optoma -3D RF 3D RF Shuer Glasses
for the ulmate in 3D stereoscopic viewing. This document describes the features, connecon, setup,
and operaon of the Optoma -3D RF Emier with Optoma 3D-XL converter box.
Features
RF synchronizaon for uninterruptable 3D glasses performance
Ready to watch compability with 3D Ready Optoma projectors with Optoma 3D-XL converter box
LED indicators assist with IR Sensor placement
Management Soware enables Upgrade funconality for compability with future 3D TVs
Manual performance adjustment capability
Copyright 2011 Bit Cauldron Corporaon Page 2 of 24
Connecons
Optoma 3D-XL converter box with 3D Emier Port
1: Connect the Optoma - emier to the Optoma 3D-XL converter box using the IR Emier Port as 3D RF
shown below.
Basic Features
RF Communicaon of Synchronizaon Signal
RF communicaons enables the Optoma - System to provide an awesome and uninterruptable 3D 3D RF
viewing experience. Line of sight obstrucons, emier placement and viewer seang arrangements
have no impact on the performance of the emier to glasses synchronizaon. Opmal seang distance
and viewing angle is determined by the capabilies of the 3D Ready Projector coupled to the Optoma
3D-XL converter box and - System. 3D RF
Copyright 2011 Bit Cauldron Corporaon Page 3 of 24
LED Indicators
The Optoma - Emier uses 5 mulcolored LEDs 3D RF
to indicate modes of operaon or other informaon.
The LEDs are located on the top of the emitter close
to the joysck and display red, green, or orange.
Joysck
The Optoma -3D RF Emier uses a joysck to allow
the user to enable various modes and change
sengs. The joysck has two axes and a center
buon funcon. Funcon of the axes and buons
are dependent on the operang mode as described
in following secons.
Modes of Operaon
The Optoma - Emier has 5 modes of operaon. 3D RF
Normal
Sync Signal Status (Strength)
Manual Tuning of Glasses Performance
Pairing the Optoma - Emier with Optoma 3D RF 3D- Glasses RF
Set Polarity
Accessing Modes
During normal operaon, the joysck is used to
access dierent modes of operaon. Press and
hold the joysck to cycle through the available
modes. Release the joysck to select a mode. In
any mode, the normal mode of operaon
resumes aer 60 seconds of inacvity with the
excepon of Set Polarity mode. Set Polarity mode
will me out in 10 seconds.
Produktspezifikationen
| Marke: | Optoma |
| Kategorie: | Projektorzubehör |
| Modell: | 3D-RF Glasses |
Brauchst du Hilfe?
Wenn Sie Hilfe mit Optoma 3D-RF Glasses benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten
Bedienungsanleitung Projektorzubehör Optoma
21 Juli 2024
20 Juli 2024
19 Juli 2024
Bedienungsanleitung Projektorzubehör
- Peerless-AV
- NewStar
- V7
- Gravity
- Christie
- BenQ
- Chief
- Konig & Meyer
- Sanus
- Barco
- Da-Lite
- Sanyo
- Vision
- Peerless
- Sony
Neueste Bedienungsanleitung für -Kategorien-
28 September 2024
23 September 2024
15 September 2024
13 September 2024
6 September 2024
5 September 2024
5 September 2024
5 September 2024
5 September 2024
5 September 2024