Orion WB-4780 Bedienungsanleitung
Orion
Nicht kategorisiert
WB-4780
Lies die bedienungsanleitung für Orion WB-4780 (4 Seiten) kostenlos online; sie gehört zur Kategorie Nicht kategorisiert. Dieses Handbuch wurde von 16 Personen als hilfreich bewertet und erhielt im Schnitt 4.3 Sterne aus 8.5 Bewertungen. Hast du eine Frage zu Orion WB-4780 oder möchtest du andere Nutzer dieses Produkts befragen? Stelle eine Frage
Seite 1/4
Tilt adjusting knob
INSTALLATION INSTRUCTIONS
ISSUED: OCT.2012
7
Tilting Wall Mount
4. Adjustment
3. Hang Display onto the Wall Plate
CAUTION: DO NOT EXCEED MAXIMUM
LISTED WEIGHT CAPACITY. SERIOUS
INJURY OR PROPERTY DAMAGE MAY
OCCUR!
75kg
(165lbs)
MAX
Loose the adjusting knobs to tilt desired angle then tighten them.
Maintenance
• Check that the bracket is secure and safe to use at regular intervals(at least every three months).
• Please contact your dealer if you have any questions.
WB-4780
400x400/600x400
800x400/800x600 70"
MAX
0°
-10°
wall
Tighten bottom bolts to secure display brackets to the wall plate.
wall
Bolt
Premium Mount Inc
7300 Bolsa Ave., Westminster, CA 92683 -
Phone: 714-766-6303
2
Component Checklist
IMPORTANT: Ensu re tha t you ha ve rec eived all pa rts according to t he compon ent checklist pr ior to installin g. If
any parts are missing or f aulty, telephone your local distributor f or a replacement .
Package M
Package W
ST6.3x55 (x6)
W-A
concrete anchor (x6)
W-B
D6 washer (x6)
W-C
1
NOTE: Read the entire instruction manual before you start installation and assembly.
WARNING
• Do not begin the installation until you have read and understood the instructions
and warnings contained in this installation sheet. If you have any question
regarding any of the instruction or warning, please contact your local distributor.
• This mounting bracket was designed to be installed and utilized ONLY as
specified in this manual. Improper installation of this product may cause damage
or serious injury.
• This product should only be installed by someone of good mechanical ability,
with basic building experience and fully understanding of this manual.
• Make sure that the supporting surface will safely support the combined load of
the equipment and all attached hardware and components.
• If mounting to wood wall studs, make sure that mounting screws are anchored
into the center of the studs. The use of a stud finder is highly recommended.
• Always use assistant or mechanical lifting equipment to safely lift and position
equipment.
• Tighten screws firmly, but do not over tighten. Over tightening can damage the
items, greatly reducing their holding power.
• This product is intended for indoor use only. Using this product outdoors could
lead to product failure and personal injury.
wall plate
A
(x1)
M5x14 (x4)
M-A
M6x14 (x4)
M-B
washer
M-F
(x4)
M8x20 (x4)
M-C
big spacer (x4)
M-H
M6x30 (x4)
M-D
M8x30 (x4)
M-E
small spacer (x8)
M-G
left (x1)adapter bracket
B
right (x1)adapter bracket
C
4
3
WARNING
• Make sure that mounting screws are anchored into the center of the studs. The use of a stud
finder is highly recommended.
• Installers are responsible to provide hardware for other types of mounting situations.
• Installers must verify that the supporting surface will safely support the combined load of the
equipment and all attached hardware and components.
1a. Mount on Wood Stud Wall
• When installing wall mounts on cinder block, verify the actual concrete thickness is at least
1-3/8" (35mm) for using the concrete anchors. Do not drill into mortar joints! Be sure to
mount in a solid part of the block, generally 1" (25mm) minimum from the side of the block.
It is suggested electric drill on slow setting be used to drill the hole instead of a hammer drill
to avoid breaking out the back of the hole when entering a void or cavity.
• Installers must verify that the supporting surface will safely support the combined load of the
equipment and all attached hardware and components.
WARNING
1b. Mount on Solid Brick and Concrete Block
W-C
Screw the wall
plate onto
the wall
Drill pilot holes
X X
√
1
2
3
Find and mark the
exact location of
mounting holes
ø 4.5mm
(ø 3/16")
55mm
(2.2")
55mm
55mm
55mm
55mm
2
2
2
2.
.
.
.2
2
2
2"
"
"
"
(
(
(
()
)
)
)
55mm
(2.2" )
X X
√
Screw the wall
plate onto
the wall
Drill pilot holes
1
2
Mark the exact
location of
mounting holes
60mm
(2.4")
60mm
60mm
60mm
60mm
2
2
2
2.
.
.
.4
4
4
4"
"
"
"
(
(
(
()
)
)
)
60mm
(2.4")
ø 10mm
(ø 3/8" )
W-A
W-C
W-B W-A
Produktspezifikationen
| Marke: | Orion |
| Kategorie: | Nicht kategorisiert |
| Modell: | WB-4780 |
Brauchst du Hilfe?
Wenn Sie Hilfe mit Orion WB-4780 benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten
Bedienungsanleitung Nicht kategorisiert Orion
6 September 2024
6 September 2024
1 September 2024
1 September 2024
1 September 2024
27 August 2024
27 August 2024
18 Juni 2024
18 Juni 2024
Bedienungsanleitung Nicht kategorisiert
- SEA-PRO
- Magmatic
- Merlin
- Vipack
- Red Digital Cinema
- Connect IT
- DEERSYNC
- Igloohome
- Blumfeldt
- Rösle
- Winston
- Thomann
- Origin Storage
- Alfatron
- Megger
Neueste Bedienungsanleitung für -Kategorien-
17 Juni 2025
17 Juni 2025
17 Juni 2025
17 Juni 2025
17 Juni 2025
17 Juni 2025
17 Juni 2025
17 Juni 2025
17 Juni 2025
17 Juni 2025