OSD Audio Speaker Selector 12 Bedienungsanleitung

Seiten 1 Engels Schalter

Lies die Bedienungsanleitung für OSD Audio Speaker Selector 12 kostenlos online oder lade das PDF herunter. 40 Personen fanden diese Anleitung hilfreich. Frage zu diesem Modell? Stelle eine Frage

PDF herunterladen (0.3 MB) Technische Daten

TSM8/ TSM12

Autoformer Based Speaker Selector

Instruction Manual

AUDIO

OSD

Thank you for giving OSD AUDIO the chance to earn your business! We are condent you will nd that OSD oers an outstanding combination of performance

and value in everything we make. To ensure you get the most out of your new TSM8/ TSM12, please take a moment to read this manual before you get started.

OSD Audio • 1405 t • ea • A • 92821 •• Tel (562) 697-2600 • Pioneer SBrC www.osdaudio.com Fax (562) 697-2668

1. Connections

To connect the amplifiers/receivers to the speaker selector, remove the AMP A/B connector by firmly pulling it out of its 8-pole socket. Strip ” of insulation from the end 1/4

of each wire. Tightly twist the end of each wire until no frayed ends remain. Insert each wire into the appropriate hole on the removeable terminals (matching up the

polarity). Use a small screwdriver to tighten each wire into the AMP A/B connector. Insert the connector plug into the socket and lock in place Be sure not to reverse .

these connections or the will not functionproperly. TSM12 /TSM8 Follow the same procedureto connect each ir spaofpeakers to pthe apropriate speaker connector terminal,

observi pper channngroel and polarity. If external volume control s are used, t sconnecpeaker wire rfromtheappopriate speakerconnectoronthe TSM12/ TSM8to the volume

corontl input. r tSpeakeconnecions scanupport ltie rs muplspeakerpaiwired inpa rallel or series, providedthei r combimined pedncea is a minimumof 4 s.ohm

2. Operation

To u fe oensre saperation of theamplifie r, animpedance level must fi rst beselected usingthe rotary switch llabeed speaker pair tlocaedon the of rearthe unit. This switch should

be to e l nsetthtotaumspber of eakerpair s i bengconnecedt to theun it. Set the switch fbased on theollowingconditions:

If thempli afier andthe spea kersare both 4 t tohm or 8 ohm, seheota rry switch to thenu mberofpair of speakers e connectedtothTSM12 /TSM8.

If thempli afier is 8 tohmandhespeakers are 4 tohm,sethe rotary switch to TCE WIthe numbe r of ir spaofpeakerconnec eds t to TSM12 /TSM.8

If e r 4 othamplifieishms and akethe spers are 8 oh, set the rory switch to HAmstaLF the nu mber ofpai r of speakeconnected to the rs TSM12 /TSM8.

After ng settitheproperimpedancelevel, thespeakers can be turned on and off in any combination.

Sch wwitbeteen th e A and B pamlifiers, the pushAMP A / AMP B tn lobutocaedt onthe fr .ont panel

3.SettingSystem Volume

It is important toproperlyadjustan impedance-matchingsystemto avoid distortion orDC clipping (DC voltagewillbeproduce d from aanmpifielr wthatis overorkedorthat hasan

improper lo ad). These can cause an amplifierrece/iver to go intoprotection,an d can ocauseautofrmers on volume controlstoheatup, damag ing sysemt compoentns. To set up

the system, theamplifier/rece iver volume d shoulbeat its lowest setting, andthein- wall/selector volume corntolsho uld st s beatthehigheetting.Slowlyadj ust the

amplifieivr/receer volume to a vleel that is the aacceptableformplifier to proce duwithoutclipping .

100 Watts per channels RMS continuous

200 Watts per channel average

300 Watts per channel peak

17” x 7.1” x 2.9”

Up to 14 Gauge wire

2 Years

Listening Zones:8 (TSM8)12 (TSM12)

Power:

Dimensions: L x W x H:

Cable Gauge:

Warranty:

100 Watts per channels RMS continuous

200 Watts per channel average

300 Watts per channel peak

17” x 7.1” x 2.9”

Up to 14 Gauge wire

2 Years

AUDIO

OSD

7-8

53-4

Number of

Speaker Pair

AMPLIFIERS

SPEAKERS

AMP AAMP B

AMPLIFIERS

PAIR1PAIR2PAIR3

PAIR4

PAIR5PAIR6PAIR7

PAIR8

Bewerten Sie dieses Handbuch

Produktspezifikationen

Marke:	OSD Audio
Kategorie:	Schalter
Modell:	Speaker Selector 12
Breite:	431.8 mm
Tiefe:	209.55 mm
Gewicht:	4990 g
Produktfarbe:	Schwarz
Steuerung:	Tasten
Höhe:	73 mm
Audio Kanäle:	8 Kanäle
Maximale Leistung pro Kanal:	300 W
Audio input Kanäle:	2 Kanäle
Mindestleistung pro Kanal:	100 W

Brauchst du Hilfe?

Wenn Sie Hilfe mit OSD Audio Speaker Selector 12 benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten

OSD Audio Speaker Selector 12 Bedienungsanleitung

Produktspezifikationen

Brauchst du Hilfe?

Bedienungsanleitung Schalter OSD Audio

Bedienungsanleitung Schalter

Neueste Bedienungsanleitungen für Schalter