Ozito TBS-2000 Bedienungsanleitung
Seiten 10 Engels Säge
Lies die Bedienungsanleitung für Ozito TBS-2000 kostenlos online oder lade das PDF herunter. 43 Personen fanden diese Anleitung hilfreich. Frage zu diesem Modell? Stelle eine Frage
ONLINE MANUAL
Scan this QR Code with
your mobile device to take
you to the online manual.
A A
R R
L L
1. Rear Table Extension
2. Rubber Feet x 4
3. Riving Knife
4. Blade Guard
5. Side Table Extensions x 2
6. Height Adjustment Handle
7. Bevel Adjustment Dial
8. Cross Struts x 4
9. Right Table Struts x 2
10. Rear Table Struts x 2
11. Left Table Struts x 2
12. Table Legs x 4
13. Stabilising Brackets
PARTS
FASTENERS
TBS-2000
14. Spanner (10/12mm)
15. Pin Spanner (10mm)
16. Spring Washers x 16
17. Large Washers x 8
18. Small Washers x 32
19. Hex Nuts x 32
20. Round Head Bolts x 16
21. Long Bolts x 8
22. Short Bolts (washers pre-
assembled) x 16
2
128765431311 109
1
14
222120 1918 171615
1. Separate the dierent nuts and bolts
into groups of same components and
check you have the correct quantities.
Note: The spring washers and washers
pre-assembled on the short bolts are not
included in the fastener list count.
2. Remove the screw from the height/
bevel rod and slide the bevel
adjustment dial onto the rod ensuring
the teeth on cogs align.
3. Slide the height adjustment handle
onto the rod by aligning the at
section and secure in place using the
screw that was previously removed.
4. Ensure the blade height is wound fully
down and then turn the table saw upside
down on the oor.
5. Remove any cardboard boxes from
behind the motor; it can be easily
accessed by tilting the blade using the
bevel adjustment dial.
6. Place a large washer onto each long
bolt. Insert the 4 table legs into the
bottom of the table saw and loosely
attach using the long bolts and large
washers from the outside of each leg.
Note: These bolts will need to be
removed later, so only attach loosely.
7. Attach the 4 cross struts by aligning
the holes on the strut and on the leg
(ensure the lip is facing the table saw).
Secure each end using 2 round head
bolt, washer, spring washer and nut
assemblies.
8. Attach the 2 stabilising brackets to the rear legs. Place a short
bolt through the bracket and table
leg, slide a washer onto the bolt and
then secure it with a hex nut. Repeat
for the other mounting point and
stabilising bracket.
9. Mount the rubber feet onto the bottom
of the legs.
1. ASSEMBLING THE FRAME
8x 16x 16x
22.5°
15°
30°
45°
WARNING! BEFORE ASSEMBLING YOUR TABLE
SAW OR REPLACING BLADES, ENSURE THAT THE
MOTOR IS OFF AND THE TOOL IS DISCONNECTED
FROM THE POWER SUPPLY TO PREVENT
ACCIDENTAL STARTING.
TABLE SAW
2000W 254mm
ASSEMBLY MANUAL
0920
Produktspezifikationen
| Marke: | Ozito |
| Kategorie: | Säge |
| Modell: | TBS-2000 |
Brauchst du Hilfe?
Wenn Sie Hilfe mit Ozito TBS-2000 benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten
Bedienungsanleitung Säge Ozito
Ozito ECS-406A Bedienungsanleitung Ozito PXCCSS-018U Bedienungsanleitung Ozito MSW-3000 Bedienungsanleitung Ozito MSW-3000U Bedienungsanleitung Ozito SCMS-8STANDU Bedienungsanleitung Ozito PXBCS-1830 Bedienungsanleitung Ozito TSB-0810 Bedienungsanleitung Ozito SCMS-2125U Bedienungsanleitung
Alle Ozito Säge Bedienungsanleitungen
Beliebt in Säge
Ozito SCMS-1621MS Bedienungsanleitung Ozito CSW-7000U Bedienungsanleitung Ozito ZLRSS-012 Bedienungsanleitung
Bedienungsanleitung Säge
Neueste Bedienungsanleitungen für Säge
Tolsen 79614 Bedienungsanleitung Tolsen 79551 Bedienungsanleitung JET MBS-1323EVS-H Bedienungsanleitung Tolsen 79550 Bedienungsanleitung Tolsen 87284 Bedienungsanleitung Tolsen 79538 Bedienungsanleitung Tolsen 87366 Bedienungsanleitung Tolsen 87228 Bedienungsanleitung Tolsen 87225 Bedienungsanleitung Tolsen 87360 Bedienungsanleitung