Paasche FP-4P Bedienungsanleitung

Lies die bedienungsanleitung für Paasche FP-4P (2 Seiten) kostenlos online; sie gehört zur Kategorie Nicht kategorisiert. Dieses Handbuch wurde von 47 Personen als hilfreich bewertet und erhielt im Schnitt 4.2 Sterne aus 6 Bewertungen. Hast du eine Frage zu Paasche FP-4P oder möchtest du andere Nutzer dieses Produkts befragen? Stelle eine Frage

INSTRUCTION AND PARTS LIST FP-4P 2/26/2018

Paasche Airbrush Company

9511 58th Place Kenosha, WI 53144

Website: paascheairbrush.com

E-Mail: info@paascheairbrush.com

Comes with LN-1/32 (Assembled) and LN-1/64, 3/64, and 1/16 Nibs loose

Total Length of Flow Pencil is 5 -1/2 inches.

Printed in the U.S.A.

INTRODUCTION:

The FP-4PFlow Pencil is used extensively by Cake Artists,

Bakers, and Home Bakers to decorate their Cakes, Cupcakes,

Cookies,etc. The Flow Pencil is easy to control and operate.

MIXING :

1. Proper mixing of Royal Icing & Butter Cream is essential for

continuous and uninterrupted flow.

2. Experiment with thinning of Icing for best flow.

3. Do not mix Icing in cup of Flow Pencil, use a separate

container and pour into cup only when Icing is at proper

consistency.

LOADING ICING: ( Tighten adjusting screw at rear of flow

pencil before loading Icing)

1. Remove FP-5 Cover, and pour premixed Icing into cup 3/4

full, Hold lid firmly and push plunger into cup, Pressure will

build and plunger will rise, thread lid onto cup.

2. Turning the MU-72 Adjusting Screw will control the

movement of the MU-65 Finger Lever Assembly which

controls the flow of Icing.

OPERATION:

1. Hold the FP-4P Flow Pencil in your hand as you would a

pencil or brush and place your finger lightly over the MU-65

Finger Lever. When ready to begin piping, pull back on the

MU-65 Finger Lever, when the icing begins to flow raise

the pencil up and pull in a backward motion off the surface

slightly.

2. Regulate the flow to the desired feed rate by turning

MU-72 Adjusting Screw.

3.When the plunger gets closer to the cap the flow rate will

slow down.

4.Practice on a Cake board before working on a actual cake.

5. Correct adjustment of controls and skill of operation will result

in uninterrupted and continuous piping.

CARE AND CLEANING:

1. Before storing FP-4PFlow Pencil clean it thoroughly. Rinse

cup and lid in hot water to clean out Icing,remove nib and clean

in hot water, wipe dry.

2. MU-49L Needle is held in position by MU-57 Needle Chuck

and VL-141 Locknut. Remove the needle by unscrewing the

MU-71 Handle and removing the spring. Loosen the VL-141

Locknut and then remove the needle for cleaning.

ADJUSTING OR REPLACING WORN PACKING WASHER:

1. If PTFEPacking-#6 becomes worn or loose it must be

tightened or replaced.

2. You will need a small screwdriver to remove or tighten the

Packing Nut.

3. When replacing your PTFEPacking press Packing onto the

Packing Nut-#6. Use a small screwdriver to tighten packing nut

into shell until it is tight then back out one-half turn, may vary.

4. Now insert needle - you should feel a slight resistance. If too

loose or too tight adjust the Packing Nut with screwdriver until

you feel some slight resistance.

5. Now completely re-assemble guts of Flow Pencil.

CAUTION: OVER TIGHTENING CUP WILL

CAUSE TRIGGER TO MALFUNCTION.

WARNING: Follow all safety precautions.

CAUTION:Never point flow pencil at face when pressurized.

FP-4P

(Pressure Fed)

Flow Pencil

OPERATING INSTRUCTIONS & REPLACEMENT PARTS

Produktspezifikationen