PAC OS-1 BOSE Bedienungsanleitung

Lies die bedienungsanleitung für PAC OS-1 BOSE (2 Seiten) kostenlos online; sie gehört zur Kategorie Nicht kategorisiert. Dieses Handbuch wurde von 30 Personen als hilfreich bewertet und erhielt im Schnitt 4.0 Sterne aus 8 Bewertungen. Hast du eine Frage zu PAC OS-1 BOSE oder möchtest du andere Nutzer dieses Produkts befragen? Stelle eine Frage

Pacific Accessory Corporation - 1502 S. Santa Fe Street, Santa Ana, CA 92705

[email protected] • Voice: 714-835-3022 • Fax: 714-835-3233 • www.pac-audio.com

Page

6-25-04

OS-1 BOSE

General Motors OnStar

®

Bose® Interface

Installation Instructions.

The OS-1 BOSE is a plug and play interface kit that allows replacement of a General Motors factory stereo (without RDS option)

and maintain operation of the OnStar® system and the Bose® amplifier and speakers. The kit includes the OS-1 OnStar®

interface and the OEM-1 premium sound system interface and cable . The OS-1 has on board switching, and amplifi cation to

allow audio from the OnStar® system to play through the two front factory speakers when OnStar® is active, and mute the

new replacement radio. The OS-1 can also be used when a stereo and amplifi er combination system is installed. Separate

speakers can be added if desired.

There are separate gain adjustments for left and right OnStar® audio and an LED indicator that turns on when the OS-1 receives

an “ON” command from the OnStar® system.

Cadillac

1999 - 2000 Escalade*, 2002 Escalade.

Chevrolet

1998 - 2002 Suburban and Tahoe.

GMC

1998 - 2002 Suburban,

Yukon and Denali.

Pontiac*: Please note 1998-2003 Grand Prix w/Bose® - this interface is not designed for this vehi-

cle, however, you can order the AMP-GM21B (1998-1999 Grand Prix) or AMP-GM21C (2000-2003 Grand Prix) harness

to replace the AMP-GM21A harness to make this interface work correctly.

The OS-1 will interface with all GM radios that use the 21 pin / 9 pin connectors. If there is a “RDS logo on the radio face or

the radio uses the 24 pin / 12 pin connectors, this interface will not work.

* See bulletin on page 2

OEM-1

FACTORYSOUNDSYSTEM

INTERFACE

PacificAccessoryCorporation-SantaAna,CA92705

RightFront

LeftFront

LeftRear

RightRear

OS-1

GeneralMotorsOnStar

®

Interface

FactoryRadioReplacementand

RetentionofOnStar

®

Option

PacificAccessoryCorporation-SantaAna,CA92705

OnStar

®

Active

RightFront

LeftFront

Factory9pinwireharness

Factory21pinwireharness

OEM-1PremiumSoundInterface

OS-1OnStar®Interface

OS-1618

AMP-GM21Aharness-or-

AMP-GM21B(PontiacGrandPrixonly)

(forBOSEonly!)

OS-GM9

OS-RAD

102.7FM

Aftermarketstereo

Connecting the aftermarket stereo and OS-1 to the vehicle’s factory Bose system.

Step 1.

Pre wire the OS-RAD wire harness to the aftermarket stereo wire harness. If the aftermarket stereo has a mute wire, cut the

brown wire as close as possible to the relay socket and connect it to the stereo’s mute wire (Fig. 1).

Step 2.

Use the supplied OS-1618 wire harness and connect to the 16 pin connector side to the OS-1. Connect the AMP-GM21A

wire harness and OEM-1 interface to the OS-1 according to diagram below. Connect the AMP-GM21A and OS-GM9 con-

nectors to the factory harness.

NOTES:

WARNING!

(Vehicles equipped with a 9 pin Y connector) Do not unplug the separate 9 pin female and male connectors that are

located farther back in the dash. Doing so will disconnect OnStar® from the OS-GM9 connector.

• Remember to reset OnStar® by turning the ignition off for at least two minutes prior to testing.

• The AMP-GM21A wire harness will ONLY work on a vehicle with a BOSE premium sound system.

Produktspezifikationen