PAC RP4-MZ11 Bedienungsanleitung

Lies die bedienungsanleitung für PAC RP4-MZ11 (7 Seiten) kostenlos online; sie gehört zur Kategorie Nicht kategorisiert. Dieses Handbuch wurde von 34 Personen als hilfreich bewertet und erhielt im Schnitt 4.3 Sterne aus 17.5 Bewertungen. Hast du eine Frage zu PAC RP4-MZ11 oder möchtest du andere Nutzer dieses Produkts befragen? Stelle eine Frage

RP4-MZ11

Radio Replacement & Steering Wheel Control Interface

for MazdaVehicles

Pacic Accessory Corporation

® | Santa Ana, California 92705 | Ph. 866-931-8021 | support@pac-audio.com

©2012 Pacic Accessory Corporation

www.pac-audio.com

Rev. 081612

C

Page 1

Introduction & Features

Important Notes

The RP4-MZ11 interface allows the replacement of a factory radio in select Mazda vehicles with MS-CAN radios. Using

this interface will retain factory features such as steering wheel controls (SWC), programming of the clock on the OEM

LCD screen, vehicle information on the OEM LCD screen and the BOSE amplier when the original radio is removed. The

RP4-MZ11 also provides data bus driven outputs such as retained accessory power (RAP), vehicle speed sensor (VSS),

illumination, reverse trigger and parking brake.

1. The radio select rotary switch on the side of the interface must be adjusted to the proper radio setting before plugging the

interface into the vehicle (see below for setting chart).

2. If using this interface in a Mazda CX-5, all vehicle settings must be nalized before removing the factory radio.

3. When the interface is rst plugged into the vehicle the LED will ash indicating that it is initializing. Once initialization is complete

the LED will illuminate and should be on at all times when the interface is on.

4. The following vehicles will not provide a VSS signal as this information is not on the data bus: RX-8, 2007-2009 CX-9 w/non-nav

radio, Miata

5. The following vehicles will not provide a reverse output as this information is not on the data bus: RX8, 2007-2009 CX7, 2010

Mazda 5, Miata

6. The following vehicles will not provide a parking brake output as this information is not on the data bus: RX-8, Miata

7. The following vehicles have a speed based parking brake wire that will provide a negative trigger until the vehicle is going at

least 4 mph: 2007-2009 CX-9, 2007-2009 CX-7

8. The LED will also ash whenever a SWC button is pressed

9. The interface comes pre-programmed for all of the vehicles factory SWC functions and does not require programming unless

you wish to re-assign the SWC functions to different buttons. The SWC can always be restored to default settings by pressing

and releasing the program button on the side of the interface once and waiting 7 seconds for the LED to ash 4 times.

10. The LED will ash whenever a SWC button is pressed.

Wiring Connection Chart

Red / WhiteP.B. Output (-)

Purple / WhiteVSS Output

Red Acc. Output (1 amp)

Green/ White2nd SWC Input

(Connect to blue

wire in vehicle con-

nector in Mazda

CX-5, not used in

other applications)

Green Reverse Output (+)

Orange Illumination

Interface Connector

Yellow Battery +12v

Black Ground

BlueAntenna On Input

(connect to Green/

White wire in inter-

face connector in

the Mazda CX-5)

Orange/White Illumination

White Front L + input

White / BlackFront L - input

GreyFront R + input

Grey / BlackFront R - input

Green Rear L + input

Green / BlackRear L - input

PurpleRear R + input

Purple / BlackRear R - input

Vehicle ConnectorSWC Connector

Blu/YelKenwwod, Newer

JVC, OEM or

Blaupunkt

3.5mm JackAlpine, JVC,

Clarion, Pioneer,

Sony, Fusion, Valor,

Boyo, Dual, Visteon

or Advent

Produktspezifikationen