PAC SWI-CP2 Bedienungsanleitung
PAC
Nicht kategorisiert
SWI-CP2
Lies die bedienungsanleitung für PAC SWI-CP2 (7 Seiten) kostenlos online; sie gehört zur Kategorie Nicht kategorisiert. Dieses Handbuch wurde von 15 Personen als hilfreich bewertet und erhielt im Schnitt 4.4 Sterne aus 8 Bewertungen. Hast du eine Frage zu PAC SWI-CP2 oder möchtest du andere Nutzer dieses Produkts befragen? Stelle eine Frage
Seite 1/7
SWI-CP2
Universal Steering Wheel Control Retention Interface
TM
Steering Wheel Control Interface
P Aifi C ti
Rev. 051617 Page 1
Copyright © 2017. A Pll rights reserved. PAC is a ower Brand of AA PM Global.
PAC-audio.com
Introduction & Features
Features
The SWI-CP2 interface allows the retention of steering wheel controls (SWC), rear seat controls (RSC) and retained
accessory power (RAP) whenever replacing a factory radio. Use of this interface also allows you to program two radio
functions to each SWC button by using short press/long press dual command functionality. The SWI-CP2 works in
vehicles with either data or analog SWC.
Interface & Wiring Overview
• Compatible in vehicles equipped with L N, LIN, C N, Class II, A A Analog or Serial Data SWC
• (DVLO\FRQ¿JXUDEOHXVLQJHLWKHUD3&RUPDQXDOO\
• Retains memory even if power is lost
• bility to assign two radio functions to one SWC buttonA
• Updatable via the Control ro C P P Application.
• &UHDWHDQGVDYHFXVWRPYHKLFOHFRQ¿JXUDWLRQ¿OHVIRUODWHUXVH
• Highly visible tricolor LED to keep the user informed of the modules status.
• Equipped with a manual learning function for compatibility with unlisted vehicles equipped with analog steering wheel controls.
Vehicle
Dipswitches USB PortStatus LED Radio
Dipswitches
Programming
Button
(-) Chassis Ground
(+) Constant 12v Input
White/Red
Pink
White/Black
Red
Red/White
Black
(-) Analog SWC GroundBlack
Yellow
(-) Analog SWC Input 3
Data 1 Input (LAN, MSCAN, SWCAN, LSFT)
(-) Analog SWC Input 2
(+) Accessory 12v Input
(+) Accessory 12v Output
Blue/Yellow SWC Output - Kenwood/Newer JVC
Purple
White
Light Green
Data 2 Input (LIN, IBUS, CLASSII, SERIAL)
(-) Analog SWC Input 1
(+) 12v Analog SWC Input
3.5mm Jack
SWC Output - Alpine, JVC, Clarion,
Pioneer, Sony, Boyo, Dual, Advent,
Lightning Audio or Visteon
SWI-CP2
Universal Steering Wheel
Control Retention Interface
3OHDVHYLVLWZZZSDFDXGLRFRPFRQWUROSUR$SSWRGRZQORDGWKH3&DSSOLFDWLRQWKDWSURYLGHVYHKLFOHVSHFL¿FZLULQJ
DQGYHKLFOHFRQ¿JXUDWLRQSURFHVVHV
SWI-CP2
Universal Steering Wheel Control Retention Interface
TM
Steering Wheel Control Interface
P ifi A C ti
Rev. 051617 Page 2
Copyright © 2017. A Pll rights reserved. PAC is a ower Brand of AA PM Global.
PAC-audio.com
Alpine Clarion/Nakamichi Fusion JVC Kenwood Other Pioneer Sony
Radio Dipswitch Settings
Other Advent, BOYO, Dual, Lightning Audio, Visteon, Rockford FosgateͲ
0DQXDO&RQ¿JXUDWLRQ0RGH
This is the fastest most convenient way to program our module. This method only requires you to look up the dipswitches and
wiring via our C, P Android or Apple application, set the dipswitches and then connect it to the vehicle/radio for it to function.
:LWKWKLVPHWKRGWKH&3XVHVDSUHGHWHUPLQHGGLSVZLWFKFRQ¿JXUDWLRQWRDVVLJQWKHYHKLFOHDQG6:&EXWWRQIXQFWLRQDOLW\
7KHGLSVZLWFKHVRQWKHVLGHRIWKHLQWHUIDFHPXVWEHPDQXDOO\VHWWRWKHSURSHUFRQ¿JXUDWLRQE\WKHXVHU7KHVHYHKLFOHVSHFL¿F
GLSVZLWFKVHWWLQJVFDQEHIRXQGE\GRZQORDGLQJ\RXUGHYLFHVSHFL¿F&RQWURO3URDSSOLFDWLRQIURPZZZSDFDXGLRFRPFRQWUROSUR
app. If you wish to re-assign button functions or use short press/long press dual command functionality, please follow the button
re-assignment procedure outlined on page 5.
1. 3OHDVH 9LVLW ZZZSDFDXGLRFRPFRQWUROSURDSS WR GRZQORDG WKH \RXU GHYLFH VSHFL¿F &RQWURO3UR DSSOLFDWLRQ /DXQFK WKH
DSSOLFDWLRQDQG¿QG\RXUYHKLFOHUDGLRFRPELQDWLRQ
2. Set the vehicle dipswitches according to the application.
3. Set the radio dipswitches according to the chart below.
4. Wire up the interface according to the installation instructions in the application.
App Mode
With this method, the C 2 can be connected to a P PC in which the application assigns the vehicle and SWC button functionality.
The dipswitches on the side of the interface must all be set to down/on which is the default position. When using this method, it is
not required to manually program the SWC buttons when programming via App mode.
1. Visit www.pac-audio.com/controlpro/app to download the Control ro C application.P P
2. &RQQHFWWKH&3WRWKH3&:KHQXVLQJD3&WRFRQ¿JXUHLWLVQRWUHTXLUHGWRSRZHUWKHPRGXOHYLDWKHSLQFRQQHFWRU
PLEASE NOTE: It may be necessary to update your Microsoft .NET Framework. If you require this update your C will P
DXWRPDWLFDOO\QRWLI\\RX,I\RXGRQRWJHWDQRWL¿FDWLRQWKHQ\RXGRQRWUHTXLUHWKHXSGDWH
3. Launch the application or software and follow the on screen prompts.
Manual Programming Mode
With this method the SWC values must be manually programmed into the C 2 by using the programming button. The vehicle P
dipswitches on the side of the interface must all be set to the up (off) position. The radio dipswitches must be set to the proper
UDGLRFRQ¿JXUDWLRQVHHEHORZPLEASE NOTE: This mode is only compatible in vehicles with both analog SWC and a
discrete 12v Accessory wire. Vehicles with CAN-Bus buttons cannot be manually programmed.
1. Visit www.pac-audio.com/controlpro/app to download the Control ro C application. P P
2. /DXQFKWKHDSSOLFDWLRQDQG¿QGWKHLQVWDOODWLRQLQVWUXFWLRQVIRU\RXUYHKLFOH
3. Set the radio dipswitches according to the chart below.
4. Wire up the interface according to the installation instructions in the application.
5. Connect the C 2 to the vehicle P
6. You can now follow the programming instructions on the next page.
&RQ¿JXULQJ3URJUDPPLQJ
Installation
3OHDVHYLVLWZZZSDFDXGLRFRPFRQWUROSUR$SSWRGRZQORDGWKH3&DSSOLFDWLRQWKDWSURYLGHVYHKLFOHVSHFL¿F
ZLULQJ DQG FRQ¿JXUDWLRQ SURFHVVHV :H UHFRPPHQG WKDW DOO ZLULQJ FRQQHFWLRQV EH VROGHUHG WR HQVXUH D
sturdy and reliable connection.
SWI-CP2
Universal Steering Wheel Control Retention Interface
TM
Steering Wheel Control Interface
P ifi A C ti
Rev. 051617 Page 3
Copyright © 2017. All rights reserved. PAC is a Power Brand of AAMP Global.
PAC-audio.com
Alpine JVC Kenwood Clarion Other Pioneer Sony Fusion
1 Volume + Volume + Volume + Volume + Volume + Volume + Volume + Volume +
2 Volume - Volume - Volume - Volume - Volume - Volume - Volume - Volume -
3 Mute Mute Mute Mute Mute Mute Mute Mute
4 Preset + Source Source Source Preset + Preset + Preset + Source
5 Preset - Track + Play Search + Preset - Preset - Preset - Track +
6 Source Track - Track + Search - Source Source Source Track -
7 Track + Band / Disc + Track - Band Track + Track + Track + Audio
8 Track - Preset / Disc - Disc / FM + Send / End Track - Track - Track - Power
9 Power Select Disc / AM - Send Band Band Band
10 Enter/Play Attenuation Answer End Answer Phone Menu
Reject Call / Source
(Bluetooth
equipped radios
only)
11 Band / Program Phone Receive Voice Dial VR End Answer Call Answer / End Call
12 Receive Phone Reject On Hook PTT End Call VR
13 End Voice Dial Off Hook VR
14 VR Power Mute (Multimedia
units only)
15 Preset +
- Advent, Boyo, Dual, Lightning Audio, Jensen, Rockford Fosgate & Visteon - Jensen & Advent ONLY
PLEASE NOTE: This section only applies to button programming in manual programming mode. If you are using the CP2
LQPDQXDOFRQ¿JXUDWLRQPRGHVSHFL¿FYHKLFOHGLSVZLWFKVHWWLQJVDQGZLVKWRUHDVVLJQEXWWRQIXQFWLRQVSOHDVHIROORZ
the “SWC Button Re-assignment Procedure” on page 4.
Please read each of the following steps to familiarize yourself with the process before beginning. The interface must be programmed
LQWKHVSHFL¿FRUGHUVKRZQLQWKHFKDUWEHORZ
1. Turn the key to the ignition position. The LED will illuminate red.
2. Press and hold the programming button on the side of the interface until the LED illuminates green. Release the
programming button.
3. Within 7 seconds, press the button that is to be learned on the steering wheel. At this point you have two options:
a. For short press functionality: Hold the button on the steering wheel until the LED changes from green to red.
Release the button.
b. For long press functionality: &RQWLQXHWRKROGWKHEXWWRQXQWLOWKH/('ÀDVKHVEHWZHHQUHGDQGDPEHURQFH
Release the button.
4. If you need to program more buttons, repeat step 3 for each additional audio function on the steering wheel.
5. If you come across a function in the chart that your steering wheel does not have, or you do not want to program, press
and release the program button on the side of the interface to skip that function. The LED will turn off then back on when
the skip has been done successfully.
6. 2QFHSURJUDPPLQJLVFRPSOHWHGZDLWVHYHQVHFRQGV7KH/('ZLOOÀDVKJUHHQWLPHVLQGLFDWLQJWKHHQGRISURJUDPPLQJ
7. Test the interface for proper functionality. Whenever a SWC button is pressed the LED on the interface should blink green.
If any function does not work, repeat the programming steps.
Manually Mapping the SWC Buttons
Radio Function Mapping Order
Produktspezifikationen
| Marke: | PAC |
| Kategorie: | Nicht kategorisiert |
| Modell: | SWI-CP2 |
Brauchst du Hilfe?
Wenn Sie Hilfe mit PAC SWI-CP2 benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten
Bedienungsanleitung Nicht kategorisiert PAC
6 September 2024
6 September 2024
6 September 2024
6 September 2024
6 September 2024
6 September 2024
6 September 2024
6 September 2024
6 September 2024
6 September 2024
Bedienungsanleitung Nicht kategorisiert
- Zipper
- Muse
- Aquadon
- Sandia Aerospace
- Lockwood
- Kelty
- Murr Elektronik
- Rigol
- Hortus
- Clean Air Optima
- Beverage-Air
- Wavtech
- ESE
- Shokz
- Microboards
Neueste Bedienungsanleitung für -Kategorien-
16 Juni 2025
16 Juni 2025
16 Juni 2025
16 Juni 2025
16 Juni 2025
16 Juni 2025
16 Juni 2025
16 Juni 2025