Panduit MTRTH Bedienungsanleitung
Panduit
Nicht kategorisiert
MTRTH
Lies die bedienungsanleitung für Panduit MTRTH (8 Seiten) kostenlos online; sie gehört zur Kategorie Nicht kategorisiert. Dieses Handbuch wurde von 22 Personen als hilfreich bewertet und erhielt im Schnitt 4.8 Sterne aus 11.5 Bewertungen. Hast du eine Frage zu Panduit MTRTH oder möchtest du andere Nutzer dieses Produkts befragen? Stelle eine Frage
Seite 1/8
MTRTH & MTRTLS: PA25279A01_02 Page: 1 of 8 4-2009
MTRTH and MTRTLS PA25279A01
Rev. 02 4-2009
MRT and MRS METAL CABLE TIE RETAINED TENSION INSTALLATION TOOLS
OPERATION INSTRUCTIONS
© Panduit Corp. 2009
INTRODUCTION
The MTRTH Retained Tension Installation Tool is used for installing PANDUIT MRT and MRS Ball Lock
Ties in widths of 5/16” (7.9mm) Heavy (H) cross-sections.
The MTRTLS Retained Tension Installation Tool is used for installing PANDUIT MRT and MRS Ball Lock
Ties in widths of 3/16” (4.6mm) Standard (S) cross-sections. Included with this tool is an anvil, which can
be changed for installing MRT and MRS ties in widths of 1/4” (6.4mm) Light-Heavy (LH) cross-sections.
Changeover Kits are available (listed on Page 7), which allow installation of all three cross-sections of
MRT and MRS Ties with either tool.
Note: This tool is not intended for other uses such as cutting or tensioning other types of
fastening devices.
SAFETY PRACTICES
ALWAYS wear safety glasses when using this tool.
DO NOT place fingers near cutting blade during tool actuation.
Fingers may be pinched or injured by cutter blade.
DO NOT use tool on live electrical sources.
TOOL FEATURES
A. Ball Set / Cutting Handle Lever
B. Upper Handle
C. Tension Indicator Window
D. Tension Handle
E. Adjustment Knob
F. Tensioning Split Mandrel
G. Detent and Setshear Finger
H. Anvil
NOTE: In the interest of higher quality and
value, PANDUIT products are continually being
improved and updated.
Consequently, pictures may vary from the
enclosed product.
Website: www.panduit.com
E-mail: cs@panduit.com
Technical Support:
See back cover for contact
information.
MTRTH and MTRTLS OPERATION INSTRUCTIONS
MTRTH & MTRTLS: PA25279A01_02 Page: 2 of 8 4-2009
MTRTH and MTRTLS TOOL MAINTENANCE
TO INHIBIT CORROSION AND MAINTAIN PERFORMANCE OF THE TOOL, KEEP THE METAL
SURFACES COATED WITH A LIGHT OIL (3-IN-ONE® OR EQUIVALENT).
The tool must be set to the proper tension range based on ties to be installed. Per the above chart, turn
the tension knob, so that mark is aligned with correct setting on Tension Setting Label (see above).
MTRTH and MTRTLS OPERATION INSTRUCTIONS
STEP 1 STEP 2
With the tie surrounding the bundle, insert the end
of the tie into the head/buckle on the tie.
Draw the tie up as tight as possible by hand.
STEP 3
Insert the end of the tie into the tool between Setshear Finger (#1) and Anvil (#2).
STRAP SIZE SETTING
3/16" (4.6mm) S
1/4" (6.4mm) LH
5/16" (7.9mm) H
Tie inserted
in gap here
#1
#2
MTRTH and MTRTLS OPERATION INSTRUCTIONS
MTRTH & MTRTLS: PA25279A01_02 Page: 3 of 8 4-2009
STEP 4
As the tie end is fed through the tool insert the tie end through the Tensioning Split Mandrel.
Pull tool tight to bundle.
CRITICAL: Tool Must Be In-line with the Tie Head
STEP 5
Produktspezifikationen
| Marke: | Panduit |
| Kategorie: | Nicht kategorisiert |
| Modell: | MTRTH |
Brauchst du Hilfe?
Wenn Sie Hilfe mit Panduit MTRTH benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten
Bedienungsanleitung Nicht kategorisiert Panduit
8 Oktober 2024
8 Oktober 2024
3 Oktober 2024
5 September 2024
4 September 2024
30 August 2024
30 August 2024
21 August 2024
21 August 2024
21 August 2024
Bedienungsanleitung Nicht kategorisiert
- Sandia Aerospace
- Scanstrut
- Burris
- Noyafa
- Eufy
- Dedra
- Sunpentown
- Bebob
- Springfree
- Genelec
- Toparc
- Hansa
- EXSYS
- Maginon
- Legrand
Neueste Bedienungsanleitung für -Kategorien-
16 Juni 2025
16 Juni 2025
16 Juni 2025
16 Juni 2025
16 Juni 2025
16 Juni 2025
16 Juni 2025
16 Juni 2025