Pioneer DVR-117D Bedienungsanleitung
Pioneer
Nicht kategorisiert
DVR-117D
Lies die bedienungsanleitung für Pioneer DVR-117D (2 Seiten) kostenlos online; sie gehört zur Kategorie Nicht kategorisiert. Dieses Handbuch wurde von 23 Personen als hilfreich bewertet und erhielt im Schnitt 4.4 Sterne aus 12 Bewertungen. Hast du eine Frage zu Pioneer DVR-117D oder möchtest du andere Nutzer dieses Produkts befragen? Stelle eine Frage
Seite 1/2
Step 1 – Prepare the Computer
1) Turn OFF the computer and disconnect the power cord.
2) Remove the bezel and the open drive bay cover from the computer’s front panel.
Note: Your computer may be a tower
model as shown on the left or a
desktop model as shown below. This
drive works in either PC model style.
Step 2 – Prepare the Drive
3) Attach slide rails to the drive if required for your drive model.
Slide rails are sold separately through computer retailers.
4) Position the drive close to the open computer bay.
Horizontal Installation Vertical Installation
Step 3 – Connect the Cables
5) Connect the power cable from the computer to the drive.
Pay close attention to the polarity of the cable.
6) Connect the IDE cable to the drive.
C onfirm that Pin 1 on the drive corresponds to Pin 1 on the cable.
7) Connect the drive’s audio output to the sound card if one is present.
Step 4 – Finish the Installation
8) Place the mounting screws in the appropriate holes and tighten by hand.
When mounting screws are loose, vibrations from the spinning disc may cause a ripping sound.
9) Replace the bezel and power ON the computer.
Setting the Jumper For Use in a Master/Slave PC
If you have a Master/Slave type of computer, you probably have two IDE channels, Primary and Secondary. The hard
drive is using the Primary IDE channel and any drives are using the Secondary channel. Install this drive as the Master
device on the Secondary channel and any other devices as Slaves to this new drive. Follow the directions below to
change your older drives or other equipment on the Secondary channel to a Slave device.
1) Disconnect the following drive cables in the order listed below.
Power cable
IDE cable
Audio cable
2) Remove the drive from the drive bay.
3) Use your fingers or a tool to move the jumper to the new setting.
4) Return the drive to the drive bay.
5) Reconnect the cables in the reverse order, Audio, IDE then Power.
Jumper: (jumpered = ON; no jumper = OFF)
Set the jumper to select the drive type for your computer.
Pin Name Function
1 MA on Drive set to Master mode
2 SL on Drive set to Slave mode
3 CS on Drive set to Cable Select mode
4 Reserved
5 Reserved
Master Slave Cable Select
Setting the Jumper For Use in a Cable-Select PC
Some computers support a data exchange method called Cable Select. If your PC uses Cable Select then all devices
need to be set to Cable Select as well. Also, the IDE cable must be designed for Cable Select communication.
Simply position the jumper for Cable Select and install the drive according to the instructions beginning on the opposite
side of this paper. No other changes are required when using Cable Select computers.
Do Not jumper the drive to Cable Select unless your PC uses this method.
Produktspezifikationen
| Marke: | Pioneer |
| Kategorie: | Nicht kategorisiert |
| Modell: | DVR-117D |
Brauchst du Hilfe?
Wenn Sie Hilfe mit Pioneer DVR-117D benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten
Bedienungsanleitung Nicht kategorisiert Pioneer
25 Juli 2025
22 Juni 2025
21 Juni 2025
21 Juni 2025
21 Juni 2025
21 Juni 2025
21 Juni 2025
21 Juni 2025
21 Juni 2025
21 Juni 2025
Bedienungsanleitung Nicht kategorisiert
- Argoclima
- Arctic Cooling
- NZR
- Lyman
- Warwick
- DW
- Riello
- Bimar
- Omnitron Systems
- IFM
- Vistron
- Viltrox
- Majella
- Jensen
- Seville Classics
Neueste Bedienungsanleitung für -Kategorien-
30 Juli 2025
30 Juli 2025
30 Juli 2025
30 Juli 2025
30 Juli 2025
30 Juli 2025
30 Juli 2025
30 Juli 2025
30 Juli 2025
30 Juli 2025