Progress Lighting AirPro P2667 Bedienungsanleitung
Seiten 9 Nicht kategorisiert
Lies die Bedienungsanleitung für Progress Lighting AirPro P2667 kostenlos online oder lade das PDF herunter. Diese Anleitung wurde 0 Mal aufgerufen. Frage zu diesem Modell? Stelle eine Frage
High Speed
Medium S peed
L S owpeed
Stop
Light
Timer
A) HANDHELD REMOTE CONTROL SETUP
Install the CR2032 battery included. Remove the battery if not used for long periods of , 3V
time to prevent damage to the hand held remote. (Fig. 1)
NOTE: The Remote System is equipped with a learning frequency function that has 6 code 5K
combinations to prevent potential interference from other remote units. The frequency on
your Receiver and Transmitter units have been preset at the factory. We recommend setting
up the frequency while installing the ceiling fan instead of using the initial frequency set by the
factory. The process of changing the frequency is as below. Within 60 seconds of turning the
Receiver AC power ON, press and hold the Transmitter FAN OFF(Stop) button for at least 5
seconds.
The light kit will
ick to confirmer.
The receiver will learn the same frequency that
the transmitter has set up. After completion of above operation, you can operate the ceiling
fan and light.
If above set up is not successful, turn o
the power the receiver and repeat the above to
actions.
Safety Precautions:
WARNING: Disconnect source of electrical power by removing the fuse or switching off
circuit breakers.
• Do not use with solid state fans.
• Electrical wiring must mee
t all local and national electrical code requirements.
• Electrical source and fan must be 115/120 volts, 6
0 Hz. Maximum fan motor amps 1.5 isA.
Maximum light watts is 50W-incandescent, VA (LED). 50
1. RECEIVER INSTALLATION
NOTE: Before the electrical power is disabled for the installation of the receiver, pull chain fan
light kits must be left in the on position and the ceiling fan on the highest speed.
Step 1.
Insert Receiver into Hanger Bracket with the
at side of the Receiver facing the
ceiling. (Fig. 2a)
Step 2.
Motor to Receiver Electrical Connections: Connect the WHITE wire from the fan to
the WHITE wire marked “TO MOTOR N” from the Receiver. Connect the BLACK wire from
the fan to the BLACK wire marked “TO MOTOR L” from the Receiver. Con
nect the BLUE wire
from the fan to the BLUE wire marked “For Light” from the Receiver. (Fig.
2b )
Step 3.
Receiver to House Supply Wires Electrical Connections: Connect the WHITE wire
(Neutral) from the outlet box to the WHITE wire marked “AC in N” from th
e receiver. Connect
the BLACK wire (Hot) from the outlet box to the BLACK wire marked “AC in L” from the
receiver. Secure all wire connections with the plastic wire nuts provided. (Fig. 2b)
After all splices are made, check to make sure there are no loose strands. As an additional
precaution p1-we suggest securing the plastic wire connectors to the wires with electrical tape.
P2667 Smart Ceiling Fan WIFI Control
–
Battery
CR2032
WARNING! SHUT POWER OFF AT FUSE OR CIRCUIT BREAKER
2. OPERATING THE - MOTE CONTROL HANDHELDRE
1. Light Button:
Press and release the button to turn the light ON or OFF. Press and hold the button to set
the desired light brightness. The light will cycle between bright and dim settings as long as
the button is pressed. The light key has an automatic auto-resume feature that allows the
light to remain at the same brightness as the last time it was turned o
.
2. Speed Buttons
Press and release the button for the desired speed.
3. Stop Button
This buttostops the fan. n
4. Timer Buttons
2H, 4H, 8H timer buttons turn o
the fan after 2 hours, 4 hours, and 8 hours
Use the screw provided to install the wall holster on the wall or another convenient location of
your choice.
NOTICE!
Your ceiling fan and light kit assembly must meet the following requirements:
Do t install this fan with wall solid state speed control or wall light dimmer control. No
Itwill permanently damage the receiver of remote control and cause the fan function failure.
CAUTION
:
Ceiling Angle shall Not Exceed 30 Degrees, ForMountingcontror. Models UC7308RYF lle
Fig .1
Loosen the screw
(do not remove it)
to access battery
compartment.
Note: Make sure to
install
at side of
receiver facing the
ceiling
WARNING: CHEMICAL BURN HAZARD.
KEEP BATTERIES AWAY FROM CHILDREN.
F ID: CHQ7235T4 IC: 2968A-7235T4 CC
This device complies with part 15 of the
FCC rules. Operation is subject to the
following two conditions. (1)This device may
not cause harmful interference and, (2)This
device must accept aninterference y
received, Including interference that may
cause undesired operation.
Fig.2a
Fig.2b
( side faces +
outward)
93100817_A
Produktspezifikationen
| Marke: | Progress Lighting |
| Kategorie: | Nicht kategorisiert |
| Modell: | AirPro P2667 |
Brauchst du Hilfe?
Wenn Sie Hilfe mit Progress Lighting AirPro P2667 benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten