Pyle PDWM5900 Bedienungsanleitung
Lies die bedienungsanleitung für Pyle PDWM5900 (4 Seiten) kostenlos online; sie gehört zur Kategorie Mikrofon. Dieses Handbuch wurde von 23 Personen als hilfreich bewertet und erhielt im Schnitt 4.5 Sterne aus 12 Bewertungen. Hast du eine Frage zu Pyle PDWM5900 oder möchtest du andere Nutzer dieses Produkts befragen? Stelle eine Frage
Seite 1/4
RECEIVER
Frequency: 902~926.75MHz
Frequency Stability 10ppm：
Sensitivity: 13dBuV
Adjacent channel rejection 75dB：
Image rejection: 95dB
Audio Output 200MV：
Output Impedance: XLR connector: 200 ; 1 / 4 inch connector: 1kΩ Ω
S/N ratio: 100dB
0.1%
Frequency response: 50Hz-15KHz
: 60m
Power supply: DC12V--18V
Housing: Metal
Size(WxDxH): 16.5”x7”x1.8”
Weight: 3.3 lbs
MICROPHONE
Frequency: 902~926.75MHz
Frequency Stability: 10ppm
Transmitting power: <10mW
Spurious emission: >65dB
Modulation: FM
Max modulation: 75K
Power supply: 3V (2 AA batteries)
Current consumption: 120mA
Total Harmonic Distortion: <
Operating Range
SPECIFICATIONS
FRONT PANEL
1. CH- A Volume control
2. CH-A channel UP
3. CH-A channel DOWN
4. Infrared (IR) port
5. CH-A Sync Button
6. CH-A display
REAR PANEL
13. Antenna jack B
14. Balanced XLR output jack B
15. Mixed 1 / 4 " output jack
16. DC input jack
17. Balanced XLR output jack A
18. Antenna jack A
RECEIVER
ANT-B ANT-A
BALANCED OUT B MIXE D OUT
13 14 15 16 17 18
1. Connect one end of supplied 6.35mm to 6.35mm plug audio cable
into MIXED OUT(15) on rear panel of the receiver. Connect the
other end of the audio cable into "MIC IN" or "AUX IN" of amplifier
or mixer.
2. Connect DC plug of supplied AC/DC adapter to DC INPUT(16) jack
on rear panel of the receiver. Connect AC plug of AC/DC adapter to
mains power socket.
3. Press POWER(12) button on front panel to turn on the receiver.
4. Press CH-A UP(2) or DOWN(3) buttons to set receiver CH-A
7. CH-B display
8. CH-B Sync Button
9. CH-B channel DOWN
10. CH-B channel UP
11. CH- B Volume control
12. Power On/Off switch
OPERATION
HANDHELD MIC
1. Mesh(capsule inside)
2. LCD display(IR port)
3. Power on/off switch
4. IR port
5. Battery cover/compartment
12 3 4
OPERATION
1. Open battery cover and install 2PCS AA batteries into battery
compartment with correct polarity(match + and - signs).
2. Press and hold power button to turn on microphone.
3. Point microphone IR port to receiver IR port and press CH-A SYNC
button to set first microphone frequency to be same as receiver CH-
A frequency. Press CH-B SYNC button to set second microphone
frequency to be same as receiver CH-B frequency.
4. Receiver RF indicator will display in receiver screen.
5. During operation if power LED indicator lights red, this indicates
the battery is Iow. Please replace new battery.
6. After use please press and hold power button to turn off
the microphone. If you are not going to use this system for a long
period of time please take out the batteries from
the microphone to avoid possible battery leakage which may
damage the microphone.
1 2 3 4 5 6 8 9 10 117 12
5
frequency. Then press CH-B
receiver CH-B frequency.
NOTE: Please must set CH-A and CH-B in different frequencies.
5. Adjust receiver volume(1, 11) and your amplifier or mixer volume to
suitable level.
UP(10) or DOWN(9) buttons to set
Produktspezifikationen
| Marke: | Pyle |
| Kategorie: | Mikrofon |
| Modell: | PDWM5900 |
Brauchst du Hilfe?
Wenn Sie Hilfe mit Pyle PDWM5900 benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten
Bedienungsanleitung Mikrofon Pyle
4 Juni 2025
5 Oktober 2024
24 September 2024
19 September 2024
17 September 2024
15 September 2024
14 September 2024
13 September 2024
12 September 2024
9 September 2024
Bedienungsanleitung Mikrofon
- HQ Power
- Majestic
- Blue
- Kopul
- Neumann
- Hähnel
- Lauten Audio
- Techly
- Renkforce
- Dörr
- Bogen
- Bose
- JB Systems
- Simplecom
- Asus
Neueste Bedienungsanleitung für -Kategorien-
16 Juni 2025
15 Juni 2025
15 Juni 2025
14 Juni 2025
14 Juni 2025
14 Juni 2025
14 Juni 2025
14 Juni 2025
14 Juni 2025
14 Juni 2025