Pyle PGRDSP61 Bedienungsanleitung
Pyle
Lautsprecher
PGRDSP61
Lies die bedienungsanleitung für Pyle PGRDSP61 (4 Seiten) kostenlos online; sie gehört zur Kategorie Lautsprecher. Dieses Handbuch wurde von 31 Personen als hilfreich bewertet und erhielt im Schnitt 5.0 Sterne aus 16 Bewertungen. Hast du eine Frage zu Pyle PGRDSP61 oder möchtest du andere Nutzer dieses Produkts befragen? Stelle eine Frage
Seite 1/4
www.PyleUSA.comwww.PyleUSA.com
Waterproof Outdoor Garden Passive Speake
PGRDSP61
6.5 Inch 6-1/2" Coaxial 2-way IP56
Questions? Issues?
We are here to help!
Phone: (1) 718-535-1800
Email: support@pyleusa.com
Features:
• Includes a 6-1/2” Coaxial Loudspeaker
• Body Made of Linear Low-Density Polyethylene
• Can be Placed on Several Surfaces, Such as Wood, Concrete or Into the
Ground
• Suitable for Installation on Different Surfaces
• Protection Grade IP56
What's in the Box:
• Speaker Box
Technical Specs:
• MAX Power: 150W
• RMS Power: 60W
• Impedance: 8 ohm
• Sensitivity: 89 dB
• Construction Material: Polyethylene with UV Prohibits
• Frequency Response: 60 Hz-20 kHz
• Speaker Diameter (Driver): 6.5 in
• AC Voltage (Minimum): 70 Volts
• AC Voltage (Maximum): 100 Volts
• Transformer Knob Style:
C70V 1W-2W-4W-8W-16W-32W & 8Ω,:
C100V 2W-4W-8W-16W-32W & 8Ω:
• Woofer Type: 6.5" Polypropylene Cone with Rubber Edge
• Tweeter Type: 1"(25mm) Titanium Dome Tweeter
• Crossover Slope: 12dB/Octave
• Product Dimension: 16.1'' x 14.4'' x 14.4'' -inches
www.PyleUSA.com www.PyleUSA.com
Read These Instructions Carefully Before Using the Product
1. Place the speaker on a level surface.
2. Do not touch or bump tbe woofer and tweeter.
Any damage will lead to sound distortion.
3. Do not listen to sound at a very high level when you are changing the input
source (for example, to tune FM/CD) installation or removal of cables should
make sure that the power amp/amplier device radio is turned off.
4. Don't attempt to clean the speakers with chemical solvents as this may
damage the paint surface. Clean only with a dry cloth.
PACKING LIST
Ensure that you have received all parts according to the component checklist
prior to installation. If any parts are missing or faulty, contact your place of
purchase for a replacement.
Direct Burial Wire or Conduit
Depending on the type of installation, direct burial of the speaker wires from
the amplier to the loudspeakers may be adequate, or the use of 1"-1-1/2"
ID conduit may be required for protecting the wires from possible physical
damage if future excavation or other alterations are anticipated in the area
of the installation.
www.PyleUSA.com
Connections Can be Protected Using One of the Following
Methods
• Solder wires together using waterproof heat shrink tubing to seal.
• Use waterproof wire connectors.
• Make connections with immersion-resistant crimp splices (Raychem).
• Use grease wire caps available from several suppliers
(Orbit,Toro lrrigation,etc.).
Connection
Use wire on the back of the speaker in the output tab of the amplier (or
ampliers of radio). The speaker wire is on one side red and on the other one
black. Connect to the red side of the amplier and speakers ( +) tab.
Connect one end of the black side(-) in the other tab. Connect each speaker
to make sure that is not ( +,-) inverted polarity. If the polarity of the speakers
is reversed, the sound will be unnatural and will play without bass.
Underpowering Vs.Overpowering
1. Most speaker damage is caused by ampliers with too little power (wattage).
2. An overdriven amplier clips the waveforms and sends distortion to the
speakers.
3. Clipping is usually audible; it may vary from a harsh sound to a fuzzy or
unclear sound.
4. If you hear the clipping at high volume levels, turn down the volume until
the distortion is gone.
5. Damage caused by operating the speakers at distorted volume levels is
not covered by the warranty.
Example of 70V/100V System Conguration
5 Speakers Connected in Parallel Using 16W Taps
NOTE:
The total number of speakers multiplied by the tap value cannot exceed the
output power (in watts) of the 70V/100V amplier.
The above example shows 5 total speakers. Using the 16W taps, you will
need an amplier with alleast (5) x (16) 80W. A good rule of thumb is to
select an amplier with 20% greater power; in this case, an amplier that
delivers about 100W.
Underpowering Vs.Overpowering
Observe correct polarity for maximum bass performance.
2 Speakers Per Channel Connected in Parallel
Speaker
User Manual
Produktspezifikationen
| Marke: | Pyle |
| Kategorie: | Lautsprecher |
| Modell: | PGRDSP61 |
Brauchst du Hilfe?
Wenn Sie Hilfe mit Pyle PGRDSP61 benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten
Bedienungsanleitung Lautsprecher Pyle
4 Juni 2025
4 Juni 2025
15 Oktober 2024
14 Oktober 2024
5 Oktober 2024
5 Oktober 2024
4 Oktober 2024
24 September 2024
20 September 2024
19 September 2024
Bedienungsanleitung Lautsprecher
- MUZEN
- Russound
- Dyon
- Albrecht
- MONDO
- Clarion
- ODYS
- Vorago
- JLab
- Motorola
- Auratone
- GoldenEar
- Luxor
- Ultron
- JVC
Neueste Bedienungsanleitung für -Kategorien-
15 Juni 2025
15 Juni 2025
15 Juni 2025
15 Juni 2025
15 Juni 2025
15 Juni 2025
15 Juni 2025
15 Juni 2025
14 Juni 2025
14 Juni 2025