Pyle Pro PDWM2450 Bedienungsanleitung

Pyle Mikrofon Pro PDWM2450

Lies die bedienungsanleitung für Pyle Pro PDWM2450 (3 Seiten) kostenlos online; sie gehört zur Kategorie Mikrofon. Dieses Handbuch wurde von 23 Personen als hilfreich bewertet und erhielt im Schnitt 4.7 Sterne aus 12 Bewertungen. Hast du eine Frage zu Pyle Pro PDWM2450 oder möchtest du andere Nutzer dieses Produkts befragen? Stelle eine Frage

Download PDF

Seite 1/3

SPECIFICATIONS

Audio Frequency Response: 50-15000Hz

Dynamic Range: ~

80dB

System Distortion:

1 %

Signal-la-Noise Ratio: ~

80dB

Operating Range: 50m-80m

Operating Temperature Range: 5

-45

Carrier

Frequency Range:

180-280MHz

Receiver:

Sensitiv / 3ity(S N= 0dB):

Image Rejection :

De-Emphasis:

Audio Output Impedance:

Audio

Out

put Level:

Power Supply:

Transmltter(hand-held):

Frequency Stability:

Output power:

Spurious Rejection:

Modulation Mode:

Max v : imum De iation Range

Microphone Mode:

Pre-Emphasis:

Pow

Supply:

Transmitter(Lapel Microphone)

Frequency Stability:

RF Output power:

Spurious Rejection:

Modulation Mode:

Maximum Deviation Range:

Microphone Mode:

Pre-Emphasis:

Power Supply:

>2mV

>40dB

5,,"8

600

0±

10%

a-o

AC110

60Hz

± O.

005

30mW

>40dB

± 75KHz

Dynamic

50""

2X1 .5V/9V BaHery

± O.005%

10mW

>40dB

± 75KHz

Dynamic

50""

9VBattery

••

lgn

and

specification

are

subject

change

without

notice

www.pyleaudio.com

PDWM

Wireless

Chann

VHF

crophone System

With

c ones roph

User

Manual

FEATURES

Operating

VHF

high

band

frequency

within

180

280MHz.

The

other

frequency is not easy

bother.

2. Crystal-controlled circuit. And

the

antenna Inside

the

unite.

3. Dual channel receiver, one receiver can receiver

two

ttransmltter

the

same

time.

4. There Is a companding function.

Audio output

adjustable with volume control.

6. Audio Display.

RECEIVER

REMARK

1 .

Power

Switch 5. Audio

Output

Jack

A & 8 CH

2. Audio Display

Audio Output Jack

Audio Volume

Audio Output Jack

4. Antenna

AC Power Jack

TRANSMITTER

REMARK

j : D

Mk><lphone

Head

Microphone

Jack

Grip

8. Microphone Input

Jack

PCM'eI'Switch

9. PowerlSensitivity

SWitch

Power IndlcatorlLow

Voltage

Indicator 10.

Belt

Clip

Battery Canister

. Battery

Compartment

Cover

Microphone Wire 12. Microphone Clip

OPERATION

1. Firstofall,

hook

powertothe

receiver

of this

system,

Tum

switch

and

Power

Indicating light will

come

Indicating that power

on, then hook up the connecting

wires attached as shown

the

drawing

and draw antenna fully.

2. Open

the

battery compartment cover

transmitter,

load

battery.

3. Tum

the power switch of microphone and

the

power Indicator will be light, that

the transmitter send the signal to the receiver.

You

can adjust the volume to the middle or more through the volume knob, then

adjust the audio amplifier

the right position.

When

the transmitter is

not

used, tum

the

powfer off.

6. When the receiver

not used, tum the power off.

7. If the unit does

not

use for a

long

time,

you

must take

out

the battery.

ATTENTION

You

had better Install your unit the place where cool and dry. do not Install

beside the window, and near the place where is too hot

too wet

too

much vibration

dust est.

2. Do not use force

switches, knobs

cords, When moving the set, first

turn the unit off.

3. Do not attempt to clean the unit with chemical solv : ents this might damage

the finish. Use a clean, dry cloth.

you use several unit at the same time, you must use these unit in different

frequency.

S. Do not break the receiver and transmitter

microphone.

Produktspezifikationen

Marke:	Pyle
Kategorie:	Mikrofon
Modell:	Pro PDWM2450
Produktfarbe:	Schwarz
Übertragungstechnik:	Kabelgebunden
AC Eingangsspannung:	110 V
AC Eingangsfrequenz:	60 Hz
Typ:	Bühnen-/Auftrittsmikrofon
Energieverbrauch:	500 mA
Mikrofon-Eingangsimpedanz:	600 Ohm
Anzahl unterstützter Akkus/Batterien:	4
Rauschverhältnis (SNR):	60 dB
Frequenzbereich:	50 - 15000 Hz
Ein-/Ausschalter:	Ja
Akku-/Batteriespannung:	9 V
Receiver enthalten:	Ja
Modulation:	FM
Dynamischer Bereich:	60 dB
Maximaler Arbeitsabstand:	60.9 m
Audioausgang:	6,3 mm