QSC CX302V Bedienungsanleitung

Lies die bedienungsanleitung für QSC CX302V (3 Seiten) kostenlos online; sie gehört zur Kategorie Empfänger. Dieses Handbuch wurde von 18 Personen als hilfreich bewertet und erhielt im Schnitt 4.4 Sterne aus 9.5 Bewertungen. Hast du eine Frage zu QSC CX302V oder möchtest du andere Nutzer dieses Produkts befragen? Stelle eine Frage

Current draw—120 VACPage 1 of 3

February 2016

Idle

Current

draw at

idle or

with very

low signal

level.

8Ω 4Ω 2Ω8Ω 4Ω 2Ω8Ω 4Ω 2Ω25V-70V-100V 25V-70V-100V 25V-70V-100V

ModelAmperesAmperes Amperes AmperesAmperesAmperes AmperesAmperesAmperesAmperes Amperes AmperesAmperes

CX302 0.93.55.4 8.6na5.1 8.712.9na8.413.922.2na

CX502 0.95.18.011.9na7.612.118.2na12.6 21.2 32.2na

CX702 0.85.07.711.5 na8.313.219.8 na15.926.741.1 na

CX902 0.95.99.213.2na10.5 16.8 24.6na20.4 34.3 52.3na

CX1102 0.97.611.6 16.6na13.1 20.3 30.4na25.1 40.6 58.6na

CX302V 1.0nr nr nr5.6nr nr nr8.0nr nr nr12.0

CX602V 0.98.7nr nr8.713.0nr nr13.020.5nr nr20.5

CX1202V 1.07.711.9nr 11.912.519.2nr 19.225.238.7nr 38.7

CX254 0.75.89.214.3na8.814.2 21.7na14.8 24.0 38.2na

CX404 0.78.112.4nr na12.219.3nr na21.733.4nr na

CX204V 0.8nr nr nr8.3nr nr nr12.7nr nr nr20.1

CX168 0.66.4 10.0nrna9.9 15.1nrna16.526.0nrna

CX108V 0.6nr nr nr6.4nr nr nr10.2nrnr nr15.6

CX Series Amplifier Current Draw—120 VAC

Current draw at 1/8 of full power is measured

with pink noise as a signal. It approximates

operating with music or voice with light clipping

and repesents the amplifier's typical "clean"

maximum level, without audible clipping. Use

these figures for typical maximum level

operation.

Current draw at 1/3 of full power is measured

with pink noise as a signal. It approximates

operating with music or voice with very heavy

clipping and a very compressed dynamic range.

Current draw at full power is measured with a 1

kHz sine wave. However, it does not represent

any real-world operating condition.

"Current draw" is the amount of AC current an amplifier demands while it is operating.

Measurements are provided for various loads at idle, 1/8 of average full power, 1/3 of average full

power, and full power, with all channels driven simultaneously. The figures shown on this sheet are

for 120 VAC usage; for 230- and 100-volt operation, see the companion sheets. For typical usage,

use the idle and 1/8 power figures.

Where an asterisk (*) appears, the data was not available at press time. The designations "na" and

"nr" respectively mean "not applicable" to the particular amplifier model and "not rated" for the

particular load impedance. Bridged mono into 8 ohms is equivalent to 4 ohms per channel; into 4

ohms is equivalent to 2 ohms per channel.

1/8 Power

1/3 Power

Full Power

Load per channel ->

Produktspezifikationen