Reflecta Visilux Studio Kit 130 Bedienungsanleitung
Reflecta
Nicht kategorisiert
Visilux Studio Kit 130
Lies die bedienungsanleitung für Reflecta Visilux Studio Kit 130 (30 Seiten) kostenlos online; sie gehört zur Kategorie Nicht kategorisiert. Dieses Handbuch wurde von 31 Personen als hilfreich bewertet und erhielt im Schnitt 4.4 Sterne aus 16 Bewertungen. Hast du eine Frage zu Reflecta Visilux Studio Kit 130 oder möchtest du andere Nutzer dieses Produkts befragen? Stelle eine Frage
Seite 1/30
MANUAL (p. 2 )
ANLEITUNG (s. 4 )
Photo studio
Fotostudio
MODE D’EMPLOI (p. 6 )
GEBRUIKSAANWIJZING (p. 8 )
Studio de photo
Fotostudio
MANUALE (p. 10 )
MANUAL DE USO (p. 12 )
Photo studio
Foto estudio
HASZNÁLATI ÚTMUTATÓ (o. 14.)
KÄYTTÖOHJE (s. 16 )
Fotóstúdió
Valokuvastudio
BRUKSANVISNING (s. 18 )
NÁVOD K POUŽITÍ (s. 20 )
Foto studio
Foto studio
MANUAL DE UTILIZARE (p. 22 )
ΕΓΧ
ΕΓΧ
ΕΓΧ
ΕΓΧΕΓΧΕΙΡΙ
ΕΙΡΙ
ΕΙΡΙ
ΕΙΡΙΕΙΡΙ∆ΙΟ
∆ΙΟ
∆ΙΟ
∆ΙΟ∆ΙΟ Σ
Σ
Σ
ΣΣ Σ
Σ
Σ
ΣΣ σ
σ
σ
σσελ
ελ
ελ
ελελXPH H ( .24 )
Studio foto
Photo studio
BRUGERVEJLEDNING (p. 26 )
VEILEDNING (p. 28 )
Fotostudie
Photo studio
ENGLISH
1
2
3
4
5
6
7
1. Test button
2. Photocell
3. ‘Ready’ indicator
4. Mains ON/OFF
5. Fuse
6. Modeling lamp switch ON/OFF
7. Sync cord
8. Flash power control
8
Flash Energy 0 W 13
Typical recycle time 2 Seconds
Stepless ash power control Full to 1/8
Recommended modeling lamp E14 bulb 75 W
Flash colour temperature Approx. 5500 K
Flash trigger Light, sync cord, manual infrared, radio.
Trigger voltage 12 V
Operating voltage 180 230 V-
Output precision Within 1%
Operation:
Switch the unit ON and set the “Flash power control” and “Modeling lamp switch” as required. When the unit
has charged to the required level, the red “Ready” indicator will light. The “Test button” should be pressed to
ensure that the flash is of the required power. Plug in the “Sync cord” and connect to the camera shutter at
“X” synchronization. Alternatively, use the built in “Photocell” or plug in the “Radio remote control receiver”.-
Power supply connections
220 V AC 50 Hz. Use the main lead supplied to connect to the main supply.
Main ON/OFF switch
Set the red illuminated On/Off switch to “ ” to turn the unit ON.
Flash power selection
The unit can oer stepless power variation from full to 1/8, rotate the power control to adjust the power
you need.
Charge
When first switched to “ ”, the red illuminated ON/OFF switch will light up. When the unit has charged to the
level set by the flash power selector, the red “Ready” Indicator will light up again. Your ash light is now ready.
2
Synchronization
- Test button: For testing, or multiple ashes can be used.
- Sync socket: The standard 0.35 cm jack type socket on the rear panel of the unit may be used for direct
connection to a camera set to “x” synchronization. A “Radio remote control receiver” may also be
plugged into this socket.
- Photocell: The unit has a built-in photocell, enabling the unit to be triggered by the ash from any
other ash unit, or a small camera mounted ashgun. The photocell is mounted behind the red
“Ready” indicator on the rear panel.
-
Modeling lamp control
Set the yellow switch to “ ” to turn on the modeling lamp and keep it on all the time.
Fuse
The modeling and ash circuitry is protected by a single 7 amp fuse mounted on the rear panel. Never replace the
fuse with one of a dierent rating. Be sure to switch OFF the unit before changing the bulb or fuse.
Warning - high voltage
Do not touch the flashtube assembly for thirty minutes after disconnecting from the supply.
Safety precautions:
To reduce risk of electric shock, this product should ONLY be
opened by an authorized technician when service is required.
Disconnect the product from mains and other equipment if a
problem should occur. Do not expose the product to water or
moisture.
Maintenance:
Clean only with a dry cloth. Do not use cleaning solvents or abrasives.
Warranty:
No guarantee or liability can be accepted for any changes and modications of the product or damage
caused due to incorrect use of this product.
General:
Designs and specications are subject to change without notice.
All logos brands and product names are trademarks or registered trademarks of their respective holders
and are hereby recognized as such.
Keep this manual and packaging for future reference.
Attention:
This product is marked with this symbol. It means that used electrical and electronic products should not
be mixed with general household waste. There is a separate collections system for these products.
3
Produktspezifikationen
| Marke: | Reflecta |
| Kategorie: | Nicht kategorisiert |
| Modell: | Visilux Studio Kit 130 |
Brauchst du Hilfe?
Wenn Sie Hilfe mit Reflecta Visilux Studio Kit 130 benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten
Bedienungsanleitung Nicht kategorisiert Reflecta
5 August 2024
3 August 2024
1 August 2024
30 Juli 2024
22 November 2023
11 November 2023
8 November 2022
5 November 2022
1 November 2022
18 Oktober 2022
Bedienungsanleitung Nicht kategorisiert
- Garden Place
- SoundLAB
- Prince
- Alpatronix
- Joie
- Lapp
- CTA Digital
- Jinbei
- NuPrime
- Zenec
- STI
- Velbus
- Vestfrost
- Sekonic
- Brinno
Neueste Bedienungsanleitung für -Kategorien-
16 Juni 2025
16 Juni 2025
16 Juni 2025
16 Juni 2025
16 Juni 2025
16 Juni 2025
16 Juni 2025
16 Juni 2025
16 Juni 2025
16 Juni 2025