Roccat Afterglow Wave Wired Controller Bedienungsanleitung
Roccat
Nicht kategorisiert
Afterglow Wave Wired Controller
Lies die bedienungsanleitung für Roccat Afterglow Wave Wired Controller (43 Seiten) kostenlos online; sie gehört zur Kategorie Nicht kategorisiert. Dieses Handbuch wurde von 8 Personen als hilfreich bewertet und erhielt im Schnitt 4.7 Sterne aus 4.5 Bewertungen. Hast du eine Frage zu Roccat Afterglow Wave Wired Controller oder möchtest du andere Nutzer dieses Produkts befragen? Stelle eine Frage
Seite 1/43
Afterglow™ Wave Wired Controller
Quick Start Guide
500-237
For:
Nintendo Switch
Nintendo Switch – OLED Model
Nintendo Switch is a trademark of Nintendo. © 2023 Nintendo
English
Deutsch
Dansk
Español
Español – Mexico
Français
Français – Canada
Italiano
Nederlands
Norsk
Polski
Português
Português – Brasileiro
Svenska
English
1. Initial Setup
A. To use the controller, plug the USB cable into the Nintendo Switch dock. The controller should automatically pair with the device.
B. If the controller does not pair automatically, go into System Settings > Controller and Sensors > Change Grip/Order.
C. When prompted, press L and R on your controller to connect.
Note: You can also pair the controller directly from the Controllers Menu found on the Nintendo Switch Home Screen and select Change
Grip/Order.
2. Audio Setup
A. Plug the 3.5mm jack of your headset or headphones directly into the 3.5mm port on the controller.
Note: The Nintendo Switch only supports one audio output at a time. When connecting your headset/headphones into the controller, audio
via HDMI connected devices (i.e., TV, amp, etc.) will be disabled. When connecting more than one USB audio device, only the first device will
have audio output.
B. The Nintendo Switch will prompt you to reconnect the controller. Press L and R to connect and audio will start playing through the
headset/headphones.
C. If you do not hear audio after reconnecting your controller, the volume on your device may be low or at 0%. To turn up the volume, hold
down the “Home” button on the controller.
Note: Under the System Settings, there’s an audio setting called “Mute when Headphones are Disconnected” that can be enabled. When
activated, this option will shut off the system speakers when unplugging or disconnecting a headset until the volume buttons are pressed, or
until this setting is manually turned off. To disable this setting manually, select System Settings > System > Mute when Headphones are
Disconnected (turn to off).
3. Volume Controls
A. To adjust the controller’s volume, hold down the “function” button (located at the center of the controller between the + and – buttons)
and then press Up/Down on the D-pad.
B. Easily mute your connected headset/headphone’s mic by pressing the “function” button twice. To unmute, press the “function” button
twice again.
Note: The volume controls only adjust the volume output by the controller, and not the volume level of the Nintendo Switch OS. Adjust the
Nintendo Switch OS volume in the device settings.
Produktspezifikationen
| Marke: | Roccat |
| Kategorie: | Nicht kategorisiert |
| Modell: | Afterglow Wave Wired Controller |
Brauchst du Hilfe?
Wenn Sie Hilfe mit Roccat Afterglow Wave Wired Controller benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten
Bedienungsanleitung Nicht kategorisiert Roccat
31 Mai 2025
31 Mai 2025
31 Mai 2025
Bedienungsanleitung Nicht kategorisiert
- Vax
- Game Factor
- Ranex
- VAEMI
- Atoll
- Ernitec
- Goodram
- Quantum
- QFX
- TrueLife
- M-e
- CVW
- Bestgreen
- Truma
- Meross
Neueste Bedienungsanleitung für -Kategorien-
30 Juli 2025
30 Juli 2025
30 Juli 2025
30 Juli 2025
30 Juli 2025
30 Juli 2025
30 Juli 2025
30 Juli 2025
30 Juli 2025
30 Juli 2025