Rolls RM316 Bedienungsanleitung
Lies die bedienungsanleitung für Rolls RM316 (2 Seiten) kostenlos online; sie gehört zur Kategorie Mischer. Dieses Handbuch wurde von 26 Personen als hilfreich bewertet und erhielt im Schnitt 4.9 Sterne aus 13.5 Bewertungen. Hast du eine Frage zu Rolls RM316 oder möchtest du andere Nutzer dieses Produkts befragen? Stelle eine Frage
Seite 1/2
RM316
3 Zone Mixer
Quick Start Guide
ROLLS CORPORATION
SALT LAKE CITY, UTAH
01/19
OUTPUT
-
OFF=UP
ON=DOWN
TALK OVER ZONE ASSIGNMENT
PHANTOM POWER
MIC/LINE
MIC/LINE
INPUT LEVEL
MIC
LINE
POWER
2
3
1
2 3
MIC 1
+15V
WIPER
GND
REMOTE
CHANNEL 3
MIC 2
MIC 3
MIC/LINE
1
3
+
-
PIN 1 GND
PIN 2 +
PIN 3
-
XLR:
MUSIC ON HOLD OUT (SOURCE 1)
1/4” BAL:
TIP +
RING
-
SLEVE GND
1/4” UN BAL:
TIP +
RING NOT USED
SLEVE GND
+15V
WIPER
GND
REMOTE
CHANNEL 2
+
OUTPUT
+15V
WIPER
GND
REMOTE
CHANNEL 1
+
-
OUTPUT
ZONE 1
ZONE 2
ZONE 3
MASTER VOLUME
ZONE
1
2
3
SOURCE 3
ZONE
1
2
3
SOURCE 2
ZONE
1
2
3
SOURCE 1
ZONE
1
2
3
MIC 3
ZONE
1
2
3
MIC 2
ZONE
1
2
3
MIC 1
1/8”
RM316
3 Zone Mixer
IN
MADE IN USA
www.rolls.com
OUTPUT
-
OFF=UP
ON=DOWN
TALK OVER ZONE ASSIGNMENT
PHANTOM POWER
MIC/LINE
MIC/LINE
INPUT LEVEL
MIC
LINE
POWER
2
3
1
2 3
MIC 1
+15V
WIPER
GND
REMOTE
CHANNEL 3
MIC 2
MIC 3
MIC/LINE
1
3
+
-
PIN 1 GND
PIN 2 +
PIN 3
-
XLR:
MUSIC ON HOLD OUT (SOURCE 1)
1/4” BAL:
TIP +
RING
-
SLEVE GND
1/4” UN BAL:
TIP +
RING NOT USED
SLEVE GND
+15V
WIPER
GND
REMOTE
CHANNEL 2
+
OUTPUT
+15V
WIPER
GND
REMOTE
CHANNEL 1
+
-
OUTPUT
ZONE 1
ZONE 2
ZONE 3
MASTER VOLUME
ZONE
1
2
3
SOURCE 3
ZONE
1
2
3
SOURCE 2
ZONE
1
2
3
SOURCE 1
ZONE
1
2
3
MIC 3
ZONE
1
2
3
MIC 2
ZONE
1
2
3
MIC 1
1/8”
RM316
3 Zone Mixer
IN
MADE IN USA
www.rolls.com
OUTPUT
+15V
WIPER
GND
REMOTE
+
-
Connection to output
The remote volume section on the rear panel of the RM316 allows the installer to place remote vol-
ume controls in any or all of the zones connected to the RM316. Wiring information is silk screened
above each remote volume connector.
Q: Does the remote volume wire carry audio signal?
A: No, the remote volume wire only carries a DC control voltage that varies according to the posi-
tion of the remote volume pot (10-100K Ohm linear potentiometer recommended). Use of the remote
volume feature will not introduce any noise or cause any signal loss.
Q: What is the maximum length that I can run a remote volume wire?
A: Wire size can aect the maximum length. You can run up to 200 feet reliably, and with high quality
wire up to 1000 feet.
Below is a diagram of how to connect the pots to the remote volume Phoenix connectors.
REMOTE PAD: 5 pin Phoenix connector for connection to a remote potentiometer for remote volume
control. A 100K Ohm potentiometer is recommended (others will work).
+15: Connection to potentiometer.
WIPER: Connection to potentiometers wiper (middle pin).
COMM: Common Ground for connection to pots.
As a note: If the potentiometer pad is working opposite of what you intended just reverse the wires
going to that potentiometer.
SPECIFICATIONS
Input Impedance: 10K Ohms balanced Line
600 Ohms balanced Mic
10K Ohms unbalanced RCA
Output Impedance: 50 Ohms balanced
Max Input Level: Mic: -30 dB
Source: +22 dB
Phantom Power: +15 Volts DC
Input Connectors: XLR and RCA
Outputs: 3 ea. Phoenix connector
Max Gain: 60 dB mic
30 dB line
S/N Ratio: >75 dB
THD: < .3%
IMD (SMPTE): < .3%
CMRR: 60 dB
Frequency Response: 20Hz to 20kHz +/- 0 dB
Power Adapter: 15VDC
Weight: 7 lbs (3KG)
Size: 19” x 1.75” x 6.5”
(48cm x 4.5cm x 17cm)
Produktspezifikationen
| Marke: | Rolls |
| Kategorie: | Mischer |
| Modell: | RM316 |
Brauchst du Hilfe?
Wenn Sie Hilfe mit Rolls RM316 benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten
Bedienungsanleitung Mischer Rolls
16 September 2025
16 September 2025
16 September 2025
26 Mai 2024
8 Mai 2024
9 April 2024
13 Januar 2024
28 November 2023
23 November 2023
16 November 2023
Bedienungsanleitung Mischer
- Yamaha
- Beem
- Proficook
- Krups
- Technics
- Pyle Pro
- Back To Basics
- Grunkel
- Trisa
- Harman Kardon
- Arzum
- DataVideo
- Blokker
- Exquisit
- E-Lektron
Neueste Bedienungsanleitung für -Kategorien-
13 Januar 2026
12 Januar 2026
9 Januar 2026
31 Dezember 2026
25 Dezember 2025
16 Dezember 2025
16 Dezember 2025
7 Dezember 2025
4 Dezember 2025
27 November 2025