San Jamar SN30 Bedienungsanleitung
San Jamar
Zeepdispenser
SN30
Lies die bedienungsanleitung für San Jamar SN30 (2 Seiten) kostenlos online; sie gehört zur Kategorie Zeepdispenser. Dieses Handbuch wurde von 48 Personen als hilfreich bewertet und erhielt im Schnitt 3.9 Sterne aus 24.5 Bewertungen. Hast du eine Frage zu San Jamar SN30 oder möchtest du andere Nutzer dieses Produkts befragen? Stelle eine Frage
Seite 1/2
SN30 Classic Soap Dispenser
San Jamar
555 Koopman Lane
Elkhorn, Wisconsin 53121
USA
T: +1.262.723.6133
F: +1.262.226.8664
www.sanjamar.com
Europe
Schoorstraat 26a,
bus I
2220 Heist-op-den-Berg
BELGIUM
T: +32 15 22 81 40
F: +32 15 22 81 48
emea@sanjamar.com
México
Av. Paseo de la Reforma No. 350 - 10
Col. Juarez
Deleg. Cuauhtemoc, CP 06600
MEXICO, D.F.
T: +52 (55) 3626 0772
mexico@sanjamar.com
© Copyright San Jamar, Inc. 2022
Canada
3280 Bloor Street West
Suite 1140
11th Floor, Centre Tower
Toronto, ON M8X 2X3
CANADA
T: +1.262.723.6133
F: +1.262.226.8664
canada@sanjamar.com
105026SJ
7
Maintenance:
Periodically give the dispenser an overall cleaning – including
internal and external parts.
Press with palm facing up
and ngers curled under
the dispenser
Mounting the Dispenser:
1. Remove the cap by pulling the cap upwards
2. Press the tab holding the backplate in place and slide
backplate down and off.
3A. (If using a level to mount the dispenser) Using a level, place
backplate on wall in the area to be mounted and mark the 3
hole locations.
3B. (If no level is available) Place backplate on wall in the area
to be mounted and mark the upper hole location. Hang the
dispenser from this single hole using supplied fasteners. Mark
the other 2 hole locations.
4. Drill holes and insert wall anchors (if used).
5. Mount backplate using the supplied fasteners.
6. Attach dispenser housing to backplate by holding the
dispenser against the wall above the backplate and sliding the
dispenser downward until there is a “click”.
7. Install the cap by holding the cap against the wall above the
dispenser housing and sliding down until there is a “click”.
Filling:
1. Remove the cap by pulling upwards.
2. Fill the dispenser with liquid soap or sanitizer.
3. Replace cap by holding the cap against the wall above the
dispenser housing and slide the cap downward until there is a
click.
4. It will take 4-8 strokes to prime the pump.
5. The dispenser is now ready for use.
6. DISCLAIMER: Soap containing scrubbers or abrasives will
cause the dispenser to leak or eventually fail. San Jamar is
not responsible for incorrect soap use that leads to faulty
dispenser operation or clogging. Use Liquid/Lotion soap.
Dispenser Activation
1. Push the lever located at the bottom, center of the cover.
1 2
4
5
3A
3B
6 7
1
Produktspezifikationen
| Marke: | San Jamar |
| Kategorie: | Zeepdispenser |
| Modell: | SN30 |
Brauchst du Hilfe?
Wenn Sie Hilfe mit San Jamar SN30 benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten
Bedienungsanleitung Zeepdispenser San Jamar
24 August 2024
24 August 2024
Bedienungsanleitung Zeepdispenser
Neueste Bedienungsanleitung für -Kategorien-
22 September 2024
6 September 2024
6 September 2024
6 September 2024
4 September 2024
4 September 2024
4 September 2024
3 September 2024
30 August 2024
30 August 2024