Sanyo LNS-T02E Bedienungsanleitung
Sanyo
Projektorzubehör
LNS-T02E
Lies die bedienungsanleitung für Sanyo LNS-T02E (4 Seiten) kostenlos online; sie gehört zur Kategorie Projektorzubehör. Dieses Handbuch wurde von 42 Personen als hilfreich bewertet und erhielt im Schnitt 4.8 Sterne aus 21.5 Bewertungen. Hast du eine Frage zu Sanyo LNS-T02E oder möchtest du andere Nutzer dieses Produkts befragen? Stelle eine Frage
Seite 1/4
PARTS LIST
Following parts are contained in the packing.
· LENS
· LENS MOUNTING SCREWS
· DRIVER
· LIGHT-BLOCK SHEET
· LENS COVER (UPPER · LOWER )
NOTES ON LENS INSTALLATION
LCD PROJECTOR LENS
MODEL NO. LNS-W02/T02
LNS-W02K/T02K Series
Lens installation should be performed by the qualified service personnel.
It should be followed by this procedure precisely.
Before attempt to install the lens, confirm the model number (both the LCD
projector and the lens) and use the proper lens.
If you have any questions, contact to the dealers.
Following checks and confirmations should be taken for safety.
Check the following things by the time of the cabinet assembly after the
lens installation.
1. Confirm the lens is securely fixed by 4 screws.
2. Wiring must not be tangled in the gear of the lens motor or the other
mechanical part.
3. There is no missing part, or no loosing mounting part.
1AA6P1P2289-- (ICSC)
1 piece
6 screws (2 for spare)
1 piece
1 sheet
1 set
LENS REPLACEMENT AND
INSTALLATION PROCEDURE
LENS REPLACEMENT AND INSTALLATION PROCEDURE
Remove screws A (2 screws).
Pull down the lower lens cover while pushing
the part D, then remove it.
Remove screws B (2 screws).
Remove screws C (2 screws) and remove
upper lens cover.
1 5Perform the steps for lens replacement and installation.to
1
1.
2.
A
Fig-1
Fig-3
●IN CASE OF MODEL WITHOUT LENS
Remove 2 screws and pull down the plate.
2
3.
4.
UPPER LENS COVER
LOWER LENS COVER
C
B
D
D
COVER PLATE
REMOVE THE LENS COVER.
(At the step , insert the light-block sheet in the same
position as the removed cover plate has been placed.
Two screws are not used.)
Use the light-block sheet included with lens.
5
REMOVE THE COVER PLATE OF THE LENS COVER. (See figure-3)
Set the light-block
sheet, so that the
large rounder side
is set over the lens.
SCREWS
LIGHT-BLOCK SHEET
Fig-2
LENS COVER
Remove 4 screws of the lens cover and
remove the lens cover.
First, set the lens at the center position with
lens shift button.
First check the shape of cabinet.
In case figure-1 cabinet.
In case figure-2 cabinet.
LENS MOTOR LEAD
CONNECTOR “ K16B”
(D)
(D)(D)
(D)
C
LENS MOTOR
❋Figure shown inside of the cabinet.
REMOVE THE LENS. (See figure-4)
1. Remove the connector “K16B” of the
circuit board.
2. Loosen the A, B, C wire holder and
remove the lens motor lead.
3. Remove screws D (4 screws) which
fastens the lens and remove the lens.
●IN CASE OF MODEL WITH LENS
B
ATTACHED DRIVER
Fig-5
LENS MOUNTING BRACKET
LENS MOTOR LEAD
CONNECTOR “K16B”
(D)
(D)(D)
(D)
B
A
LENS MOTOR
Fig-4
This part wiring should
not be tightened.
C
A
INSTALL THE LENS. (See figure-4,5)
3
1. Remove protective caps (front
and back ) on the lens.
2. Mount the lens at the lens
mounting bracket with screws
(4 screws) included with the
lens. Use the driver included
with the lens to fasten the
screws . (After using, save it for
latter use.) (See figure-5)
3. Connect the lens motor lead to
the connector “K16B” of the
circuit board. (See figure-4)
4. Fasten the lens motor lead at
the A, B, C points with wire
holder.
(See figure-4)
Produktspezifikationen
| Marke: | Sanyo |
| Kategorie: | Projektorzubehör |
| Modell: | LNS-T02E |
Brauchst du Hilfe?
Wenn Sie Hilfe mit Sanyo LNS-T02E benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten
Bedienungsanleitung Projektorzubehör Sanyo
27 Juli 2024
26 Juli 2024
23 Juli 2024
20 Juli 2024
Bedienungsanleitung Projektorzubehör
- XGIMI
- Auna
- Unicol
- NewStar
- Gabor
- ViewSonic
- Peerless-AV
- Vogel's
- Christie
- Sanus
- Peerless
- My Wall
- BenQ
- Gravity
- Kingpin Screens
Neueste Bedienungsanleitung für -Kategorien-
28 September 2024
23 September 2024
15 September 2024
13 September 2024
6 September 2024
5 September 2024
5 September 2024
5 September 2024
5 September 2024
5 September 2024