Satco S13146 Bedienungsanleitung
Satco
Nicht kategorisiert
S13146
Lies die bedienungsanleitung für Satco S13146 (2 Seiten) kostenlos online; sie gehört zur Kategorie Nicht kategorisiert. Dieses Handbuch wurde von 17 Personen als hilfreich bewertet und erhielt im Schnitt 4.7 Sterne aus 9 Bewertungen. Hast du eine Frage zu Satco S13146 oder möchtest du andere Nutzer dieses Produkts befragen? Stelle eine Frage
Seite 1/2
WARNING
• BEFORE YOU BEGIN: Read these instructions completely
and carefully. To avoid personal injury and/or product damage,
all of the instructions below must be followed.
• CAUTION: If lamp or luminaire exhibits undesirable operation
(buzzing, ickering, etc.), turn off power, remove lamp from
luminaire and contact the manufacturer or distributor.
• WARNING: Risk of re or electric shock. LED Retrot Kit
installation requires knowledge of luminaire electrical systems.
If not qualied, do not attempt installation. Contact a qualied
electrician. Installation should be performed only by a qualied
electrician in accordance with Nation Electrical Code and
relevant local code.
• WARNING: Risk of re or electric shock. Install this kit only
in the luminaires that have the construction features and
dimensions written and shown in the photographs and or
drawings and where the input rating of the retrot kit does not
exceed the input rating of luminaire.
• WARNING: To prevent wiring damage or abrasion, do not
expose wiring to edges of sheet metal or other sharp objects.
• Disconnect power at the source before installation, inspection
or removal. Do not simply switch off xture.
• This item is rated at 120VAC. Installer must determine whether
line voltage 120VAC is available at the luminaire before
installation.
• Not intended for use with emergency exit xtures or
emergency exit lights.
• Not for use with luminaire ballast.
• Do not use if product is damaged.
• This lamp is non-dimmable. Not for use with dimmer.
• Do not make or alter any open holes in an enclosure of wiring
or electrical components during kit installation.
• Risk of re or electric shock. Do not open or modify. No user
serviceable parts inside.
• Installers should not disconnect existing wires from lamp holder
terminals to make new connections at lamp holder terminals.
LED UTILITY LIGHT
Model: S13146
INSTALLATION (If replacing HID lamp with ballast)
INSTALLATION AND SAFETY INSTRUCTIONS
IMPORTANT: Read before installing xture. Retain for future reference.
Satco Products, Inc.
Brentwood, NY 11717© Copyright 2022 Satco Products, Inc. 2/22 v1.5
Instead, installers should cut existing lamp holder leads away
from the lamp holder and make new electrical connections to
lamp holder lead wires by employing applicable connections.
• Suitable for damp locations. Not for use where directly exposed
to the weather or water.
• Complies with part 15 of FCC. Operation is subject to the following
two conditions: This device may not cause harmful interference,
and this device must accept any interference received including
interference that may cause undesired operation.
• Added weight of the device may cause instability of a free-
standing portable luminaire.
• The retrot assembly is accepted as a component of a luminaire
where the suitability of the combination shall be determined by
UL or authorities having jurisdiction.
E26 BASE
OPEN
ø14" 355mm) (
4.5"
(116mm)
ON
4
OFF
1 2 3
STEP 1: Turn OFF the power to the xture.
STEP 2: Open the xture’s junction box and bypass the HID ballast, igniter (if there) and the capacitor (if there) by disconnecting the line
and neutral wires and socket black and white wires in the locations with “cross” marks in the schematic diagram. Then connect the line
to the black wire from the socket and the neutral to the white wire from the socket with wire nuts or connectors.
STEP 3: “This luminaire has been modied to operate LED lamps” shall be marked on the retrot luminaire where readily visible by
the user during normal maintenance including re-lamping.
STEP 4: Turn ON the power to the xture.
CLOSED
ø4.3" 110mm) (
6.7"
(170mm)
Capacitor
Ignitor
Lamp socket
Ballast
L
N
L
N
Wi nutre
Wi nutre
X
X
XX
USAGE
Produktspezifikationen
| Marke: | Satco |
| Kategorie: | Nicht kategorisiert |
| Modell: | S13146 |
Brauchst du Hilfe?
Wenn Sie Hilfe mit Satco S13146 benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten
Bedienungsanleitung Nicht kategorisiert Satco
20 Juni 2025
20 Juni 2025
20 Juni 2025
19 Juni 2025
19 Juni 2025
17 Juni 2025
17 Juni 2025
17 Juni 2025
17 Juni 2025
17 Juni 2025
Bedienungsanleitung Nicht kategorisiert
- Phoenix
- AVMATRIX
- Kerbl
- Hasbro
- Viatek
- Altronix
- Best Fitness
- Overmax
- Grunkel
- Tech.Inc
- Orbegozo
- Jackery
- Sanitaire
- Atdec
- GeoBox
Neueste Bedienungsanleitung für -Kategorien-
21 Januar 2026
21 Januar 2026
21 Januar 2026
21 Januar 2026
21 Januar 2026
21 Januar 2026
21 Januar 2026
21 Januar 2026
21 Januar 2026
21 Januar 2026