Scosche ITCGM01B Bedienungsanleitung
Scosche
Nicht kategorisiert
ITCGM01B
Lies die bedienungsanleitung für Scosche ITCGM01B (12 Seiten) kostenlos online; sie gehört zur Kategorie Nicht kategorisiert. Dieses Handbuch wurde von 2 Personen als hilfreich bewertet und erhielt im Schnitt 4.1 Sterne aus 1.5 Bewertungen. Hast du eine Frage zu Scosche ITCGM01B oder möchtest du andere Nutzer dieses Produkts befragen? Stelle eine Frage
Seite 1/12
ITCGM01B
IN-DASH STEREO INSTALLATION KIT FOR
2010-14 CHEVROLET CAMARO
WITH TOUCH-SCREEN INTERFACE
*Dash modification required*
LIABILITY DISCLAIMER
This instruction booklet is based on carefully documented data and research of automobile dash disassembly, wire harness/
codes and information pertaining to installation of this kit (ITCGM01B) in 2010-14 Chevrolet Camaro vehicles. Scosche Industries,
Inc. cannot be held responsible for discrepancies/inconsistencies that may occur due to the automobile manufacturing changes
or options, or damage that may occur in the automobile during the installation of components while using this booklet.
©2017 SCOSCHE INDUSTRIES, INC.
ITCGM01B 05/17
If you have any further questions, call our toll free technical help line at: 1-800-621-3695x3
INTRODUCTION/PRELIMINARY
This premium installation kit is for 2010-14 Chevrolet Camaro vehicles. Included are all the parts
you need to mount your car stereo or CD player into your vehicle’s dash. Refer to the individual
instruction in this manual to remove your vehicle’s factory radio and assemble the kit. *Dash
modification required see page 2.
CAUTION
DISCONNECT YOUR VEHICLE’S NEGATIVE BATTERY TERMINAL BEFORE THE INSTALLATION
TO HELP PREVENT ELECTRICAL DAMAGE. WE RECOMMEND THE USE OF A VOLT/OHM
METER OVER A TEST LIGHT TO CHECK WIRING. A TEST LIGHT OR GROUNDED WIRE PROBE
CAN CAUSE DAMAGE TO THE VEHICLE’S COMPUTER AND/OR DIAGNOSTIC SYSTEMS. AVOID
ALL FACTORY AIRBAG WIRING - AIRBAGS CAN ACCIDENTALLY DEPLOY CAUSING SERIOUS
INJURY OR DEATH.
NOTES
• See your vehicle’s instructions for any special tools your installation might require.
• Read all instructions accompanying your car stereo for proper wiring and mounting instructions.
1. Main panel with built-in touch screen (
*
)
2. Hazard Warning Flasher
3. Stereo mounting bracket (left)
4. Stereo mounting bracket (right)
5. Dash pocket for single din mount
6. Power harness (not shown-see page 3)
SOLD SEPARATELY:
CAMOSM OnStar retention interface
(not shown -see page 5)
1
2
5
*
3
4
2010-14 CHEVROLET CAMARO
1. Turn ignition to the ON position and shift vehicle into drive.
NOTE: In order to complete step 1 the battery must be connected. After completing
step 1, disconnect the negative battery cable and proceed to step 2.
2. Use a Panel-safe Removal Tool (PRT) to unclip Auxiliary gauge panel, unplug and remove.
3.
Use a small flathead screw driver, unclip screw cap located on the lower front side of the
shift knob.
4. Extract (1) T-20 Torx screw to remove gear shift knob.
5. Extract (4) 7mm screws securing shifter console, then with pick tool, unclip (1) clip located
on eachside under the shifter console, unplug and remove.
6. Use PRT to unclip each side panel from the center console.
7. Extract (1) Phillips head screw from each side located on the outer area of the center
console.
8. Extract (1) Phillips head screw from each side of center console’s rear panel, lift and pull
back to remove.
9. Extract (3) Phillips head screws behind center console’s armrest.
10. Extract (1) Phillips head screw in front of beverage holder.
11. Use PRT to unclip 12V and USB/3.5mm housing inside the armrest, unplug and remove.
12. Use PRT to unclip center console and remove.
13. Extract (2) 7mm screws securing radio panel located under and to the rear of A/C controls.
Use PRT to unclip radio fascia panel, unplug, and remove.
14. Extract (4) 7mm screws securing radio chassis / Drive assembly, unplug, lift away
and remove.
2
FACTORY STEREO REMOVAL
DASH MODIFICATION
BEFORE
AFTER
Use the illustrations labeled
BEFORE and AFTER for
modification location requirment.
Using a cutting tool, cut the area
as shown shaded/highlighted in
the BEFORE illustration of the
dash cavity so that it looks like
the AFTER.
Proceed to either the single DIN
assembly instruction on the next
page(3) or double DIN on page
4 after completing the dash
modification for the kit.
©2017 SCOSCHE INDUSTRIES, INC.
ITCGM01B 05/17
Produktspezifikationen
| Marke: | Scosche |
| Kategorie: | Nicht kategorisiert |
| Modell: | ITCGM01B |
Brauchst du Hilfe?
Wenn Sie Hilfe mit Scosche ITCGM01B benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten
Bedienungsanleitung Nicht kategorisiert Scosche
15 Juli 2025
15 Juli 2025
15 Juli 2025
15 Juli 2025
15 Juli 2025
15 Juli 2025
15 Juli 2025
15 Juli 2025
15 Juli 2025
15 Juli 2025
Bedienungsanleitung Nicht kategorisiert
- Proxxon
- Tascam
- Pawa
- Zotac
- GolfBuddy
- Brentwood
- Antelope Audio
- Victor
- Dobot
- Futurelight
- Venta
- Medion
- Wacker Neuson
- Lifespan
- Leifheit
Neueste Bedienungsanleitung für -Kategorien-
15 Juli 2025
15 Juli 2025
15 Juli 2025
15 Juli 2025
15 Juli 2025
15 Juli 2025
15 Juli 2025
15 Juli 2025
15 Juli 2025
15 Juli 2025