Shure BETA 52A Bedienungsanleitung

Lies die bedienungsanleitung für Shure BETA 52A (12 Seiten) kostenlos online; sie gehört zur Kategorie Dampgenerator. Dieses Handbuch wurde von 23 Personen als hilfreich bewertet und erhielt im Schnitt 4.7 Sterne aus 2 Bewertungen. Hast du eine Frage zu Shure BETA 52A oder möchtest du andere Nutzer dieses Produkts befragen? Stelle eine Frage

Model BETA 52®A User Guide

27D2799 (Rev. 5)Printed in U.S.A.

©2005, Shure Incorporated

SUPERCARDIOID DYNAMIC INSTRUMENT

MICROPHONE

GENERAL

The Shure BETA 52®A is a high output dynamic microphone

with a tailored frequency response designed specically for kick fi

drums and other bass instruments. It provides superb attack and

“ ”punch, and delivers studio quality sound even at extremely high

sound pressure levels.

The BETA 52A features a modied supercardioid pattern through-fi

out its frequency range to insure high gain before feedback and

excellent rejection of unwanted sound. A builtin dynamic locking –

stand adapter with an integral XLR connector simplies installa-fi

tion, particularly if the microphone is to be placed inside a kick

drum. The stand adapter keeps the microphone position fixed and

resists slipping, even when subjected to sharp blows and strong

vibrations. A hardened steel mesh grille protects the BETA 52A

from the abuse and wear associated with touring.

FEATURES

Frequency response shaped specically for kick drums fi

and bass instruments

Builtin dynamic locking stand adapter with integral XLR –

connector simplies setup, especially inside a kick drum fi

Studio quality performance, even at extremely high sound

pressure levels

Supercardioid pattern for high gain before feedback and

superior rejection of unwanted noise

Hardened steel mesh grille that resists wear and abuse

Advanced pneumatic shock mount system that minimizes

transmission of mechanical noise and vibration

Neodymium magnet for high signaltonoise ratio output – –

Low sensitivity to varying load impedance

Legendary Shure quality and reliability

•

•

•

•

•

•

•

•

•

APPLICATIONS AND PLACEMENT

The most common BETA 52A applications and placement tech-

niques are listed in the following table. Keep in mind that micro-

phone technique is largely a matter of personal taste there is no –

one correct microphone position.“ ”

ApplicationSuggested Microphone

Placement

Tone Quality

Kick Drum5 to 7.5 cm (2 to 3 in.) away

from beater head, slightly

off-center from beater.

Sharp attack; maximum

bass sound, highest sound

pressure level.

20 to 30 cm (8 to 12 in.)

from beater head, on-axis

with beater.

Medium attack; balanced

sound.

20 to 30 cm (8 to 12 in.)

from beater head, 15 to 20

cm (6 to 8 in.) from edge

of head.

Medium attack; thin, re-

duced bass sound.

5 to 7.5 cm (2 to 3 in.) away

from outside head, on-axis

with beater (double head

kickdrum only).

Softer attack; balanced,

resonant sound.

NOTE: To tighten the “ ”

beat, place a pillow or

blanket on bottom of drum

against beater head.

Electric

Bass Ampli-

fier

2.5 cm (1 in.) from speaker,

on-axis with center of

speaker cone.

Sharp attack; emphasized

bass.

2.5 cm (1 in.) from speaker,

at edge of speaker cone.

Sharp attack; higher fre-

quency sound.

10 to 15 cm (4 to 6 in.) from

speaker, on-axis with center

of speaker cone.

Sharp attack; full, balanced

sound.

60 to 90 cm (2 to 3 ft.) from

speaker, on-axis with center

of speaker cone.

Soft attack; mellow, higher

frequency sound.

MOUNTING THE BETA 52A ON A MICROPHONE STAND

The builtin stand adapter features a dynamic locking system –

that permits adjustments to the microphone’s position, but resists

slipping when struck or bumped. To mount the BETA 52A on a

stand and adjust its position, proceed as follows:

Screw the integral stand adapter onto the end of a micro-

phone stand (see Figure 3). Adjust the stand height and

position as necessary.

Pivot the BETA 52A until it is in the desired position rela-

tive to the drum head or loudspeaker.

Lock the BETA 52A in place by rotating the adjustment

knob on the stand adapter clockwise until it is tight. Do

NOT overtighten the knob with tools.

If necessary, make minor adjustments to the microphone

position without loosening the adjustment knob.

Connect an audio cable to the integral XLR connector.

1.

2.

3.

4.

5.

MODEL BETA 52®A

Produktspezifikationen