Skylink GT-100 Bedienungsanleitung

Lies die bedienungsanleitung für Skylink GT-100 (4 Seiten) kostenlos online; sie gehört zur Kategorie Garagentoröffner. Dieses Handbuch wurde von 49 Personen als hilfreich bewertet und erhielt im Schnitt 4.7 Sterne aus 7 Bewertungen. Hast du eine Frage zu Skylink GT-100 oder möchtest du andere Nutzer dieses Produkts befragen? Stelle eine Frage

1. INTRODUCTION

Model GT-100Garage Door CloserTM

Congratulations on your purchase of the Skylink® Garage Door Closer

Model GT-100. Skylink® Garage Door Closer is very easy to install, and

provides you with the peace of mind you have been looking for by

knowing your garage door will not be left open anymore. Skylink®

Garage Door Closer consists of 2 units:

Wall Console does not require any battery to operate and it can replace

most of the existing garage door opener’s push buttons. Garage Door

Sensor is battery operated and can be mounted on to the garage door by

double sided tape or screws. These 2 units operate wirelessly which

simplifies the installation.

Programming is very simple, you can select the time you would like the

door to be closed after it has been opened. The selectable door closing

times are 2 minutes, 5 minutes, 10 minutes and 20 minutes.

Garage Door

MonitorTM Sensor

(Battery Included)

GS-101

2. INSTALLATION (CONT)

Before installing the Skylink® garage door closer, ensure your garage

door is equipped with an external entrapment protection device, such

as an infrared beam sensor which “sees” an object obstructing the door

without having actual contact with the object. A Garage door opener does

that not have the auto reversing mechanism should be replaced by one that

has the auto reversing mechanism feature and the garage door closer

must not be installed on garage a door opener without this feature.

Without a properly working safety reversal system, a person could be

seriously injured or killed by a closing garage door.

WARNING

2. INSTALLATION

Unplug the power cord of your garage door opener

before installation to ensure power is not connected.

WARNING

The installation involves 2 units:

1) Garage Door MonitorTM Sensor

2) Wall Console

Garage Door MonitorTM Sensor

Step 1 – Select a spot on your garage door to mount

the sensor

Before you install the sensor onto the garage door,

make sure the garage door is closed. The sensor

assembly should be mounted on one of the vertical

supports of your garage door near the bottom.

When the door is closed, the detection rod should be retracted. When

the door is open, the detection rod will be extended.

Note:

When the garage door is opening/closing,

make sure the sensor does not interfere with

the safety reversing sensor or safety beam

sensor supplied with your existing garage

door opener.

Step 2 – Mount the sensor on to your garage door

You can mount the sensor onto your garage

door with double-sided foam tape if the sur-

face of your garage door is smooth and clean

enough to provide a good adhesive surface,

such surface can usually be found on a metal

garage door. Please ensure the surface is

smooth and clean. Important: The bottom

of the sensor should be 1/2 inch above

the ground. (Refer to Diagram A)

For wooden garage doors, it is recommended

to mount the sensor with screws on to the

garage door with 3 x 18 screws provided.

4 Screws

Double-sided

foam tape

1/2 Inch

Note: Ensure you straighten up the antenna

on the receiver to receive the best possible

reception. Diagram A

Wall Console

The GT-100R Wall Console replaces most garage door “push buttons” or

“wall consoles”. There are 2 different kinds of “push buttons”.

1) Single button

2) Multi-Function Wall Console

1) Single button

If your garage door opener equips with a single button “push button”,

you can replace the existing push button with Skylink® Garage Door

Closer Wall Console GT-100R. Please follow the procedures below.

1. Remove the existing push button by removing

the screws.

2. Disconnect the 2 wires that are connected to

the existing push button.

3. Connect these 2 wires to the 2 terminals on the

GT-100R Wall Console. Loosen the 2 screws

on the terminals, feed the 2 wires to the 2

terminals and tighten 2 screws to secure the

2 wires.

4. After connecting the 2 wires, the red LED under-

neath the push button will be on. The GT-100R

is now charging up. The GT-100R will be fully

charged when the buzzer emits a beep (approx

10 seconds to 1 minute depending on the brand

of garage door opener), the red LED will then

flash slowly. The GT-100R is now ready to operate.

5. Mount the Wall Console to the wall with 2 screws.

6. Straighten up the antenna on the GT-100R.

Remove

existing

wires

One of

Vertical

Supports

Door closedDoor open

Remove the battery

isolator

4 pcs 3 x 18 screws

2 pcs 3.5 x 25 screws

Double-sided

foam tape

3V Lithium battery

Extension wiresWall Console

GT-100R

Produktspezifikationen