Soler & Palau TOFFI Bedienungsanleitung
Lies die bedienungsanleitung für Soler & Palau TOFFI (6 Seiten) kostenlos online; sie gehört zur Kategorie Nicht kategorisiert. Dieses Handbuch wurde von 19 Personen als hilfreich bewertet und erhielt im Schnitt 4.2 Sterne aus 10 Bewertungen. Hast du eine Frage zu Soler & Palau TOFFI oder möchtest du andere Nutzer dieses Produkts befragen? Stelle eine Frage
Seite 1/6
1. RECOMMENDATIONS
You have purchased a TOFFI designed specifically by Soler & Palau to perform the functions described in the table of
contents.
Before you install and start up this product, please read this instruction book carefully because it contains important
information for your safety and the safety of users during installation, use and maintenance. Once installation is
complete, please pass the instruction book on to the end user. Please check that the equipment is in perfect condition
when you unpack it since any factory defect is covered under the S&P guarantee. Please also check that the
equipment is the one that you have ordered and that the information on the instruction plate meets your
requirements.
2. GENERAL
The TOFFI has been designed to provide fault indication for both AC and EC type fan motors. The device is supplied
with a jumper allowing the switch between a ‘Tacho input’ or ‘External volt free contact’ which the TOFFI continuously
monitors. In the event that it no longer receives a signal the device will indicate a fault via its fault relay. When in
fault mode the device isolates all power to the fan with a manual reset required to reset the fault.
3. SPECIFICATION
• The equipment is designed for continuous operation with a maximum rated current load of 8A at 40° C. ambient
on single phase 230 Volts ~ 50Hz supply.
• The normal equipment temperature range is -20°C to +40°C.
• The unit meets the EMC requirements of EN 61800-3:1997 and EN61000-3:2006
• The controller is housed in an enclosure that is suitable for the current rating.
4. SAFETY RULES
4.1. CAUTION
• Isolate mains supply before connecting.
• This unit must be earthed.
• All electrical connections should be made by a qualified electrician.
• All wiring must be in accordance with current wiring regulations. The unit should be provided with a separate
double pole isolator switch.
4.2. INSTALLATION
• Installation and commissioning must be done by a qualified professional specialist.
• Ensure that installation complies with mechanical and electrical regulations in each country.
• Do not use this equipment in explosive or corrosive atmospheres.
• Should the 8A current rating of the TOFFI exceed that of the equipment being connected to the volt-free output
then the TOFFI could be connected to a contactor to switch a higher load.
• Install in a dry sheltered location. Do not install in close proximity to other heat sources. The maximum ambient
temperature for the controller must not exceed 40°C.
• Remove the lid of the controller by removing the cover fixing screws. This provides access to the mounting holes
and circuit board.
5. TERMINALS
• L – Live
• N – Neutral
• E – Earth
• 0V Ground –
• FG Tacho Output –
• N/C Normally Closed –
• N/O Normally Open –
• C – Common
6. WIRING
When connecting the device, it required a closed circuit between the remote enable terminals to run, in the
event that the system is constantly running fit a link between the terminals. In the event of a fault the
relay will change condition producing continuity between ‘C’ and ‘N/O’.
6.1. EC FAN WIRING
6.2. AC FAN WIRING
Produktspezifikationen
| Marke: | Soler & Palau |
| Kategorie: | Nicht kategorisiert |
| Modell: | TOFFI |
Brauchst du Hilfe?
Wenn Sie Hilfe mit Soler & Palau TOFFI benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten
Bedienungsanleitung Nicht kategorisiert Soler & Palau
4 Juni 2025
1 September 2024
30 August 2024
13 August 2024
3 August 2024
1 August 2024
1 August 2024
29 Juli 2024
28 Juli 2024
20 Juli 2024
Bedienungsanleitung Nicht kategorisiert
- Z.Vex
- Imetec
- ElectriQ
- BlendMount
- Block & Block
- Tor Rey
- LTC
- Blackstar
- Needit
- Elro
- InfiRay
- Megger
- Tellur
- 3Doodler
- Valueline
Neueste Bedienungsanleitung für -Kategorien-
15 Juni 2025
15 Juni 2025
15 Juni 2025
15 Juni 2025
15 Juni 2025
15 Juni 2025
15 Juni 2025
15 Juni 2025
15 Juni 2025