Sonance Bandpass BPS6 Bedienungsanleitung
Lies die bedienungsanleitung für Sonance Bandpass BPS6 (2 Seiten) kostenlos online; sie gehört zur Kategorie Subwoofer. Dieses Handbuch wurde von 3 Personen als hilfreich bewertet und erhielt im Schnitt 4.7 Sterne aus 2 Bewertungen. Hast du eine Frage zu Sonance Bandpass BPS6 oder möchtest du andere Nutzer dieses Produkts befragen? Stelle eine Frage
Seite 1/2
Determine the location for the mounting platform.
Ensure there is adequate room for the BPS6
subwoofer at the location of the platform.
The speaker opening must be located within
12” (305mm) of the BPS6 to allow the port
tube to reach through the platform.
Place the mounting template on the side of
the joist and drill four 1/2” (12.7mm) holes
through the joist at the locations shown on
the mounting template.
Attach the mounting platform to the joists.
See mounting platform quickstart guide or visit
www.sonance.com/in-wall-in-ceiling/
architectural-series for detailed
installation manual.
Hold the side of the BPS6 with the rubber
damping pad up against the side of the joist
and install the four lag screws and washers to
secure the BPS6 in place.
3 4
1
12” (305mm)
BPS6
Port tube
2
(1) Quickstart guide
(1) Bandpass subwoofer w/ port tube
(1) Cardboard mounting template
Mounting screws & washers:
(4) 5/16” x 2” lag screws (for thinner beams)
(4) 5/16” x 3” lag screws (for thicker beams)
(4) 5/16” washers
Box Contents
Bandpass subwoofer can be installed in joists spaced 16” on center or greater.
AS BANDPASS STEREO SUBWOOFER QUICKSTART GUIDE
BPS6
SONANCE ARCHITECTURAL SERIES
®
©2014 Sonance. All rights reserved.
Sonance and Architectural Series are registered trademarks of Dana Innovations.
Due to continuous product improvement, all features and specifications are subject to change without notice.
For the latest Sonance product specification information, visit our website: www.sonance.com
SONANCE • 212 Avenida Fabricante • San Clemente, CA 92672-7531 USA
(800) 582-7777 or (949) 492-7777 • FAX: (949) 361-5151 • Technical Support: (800) 582-0772
www.sonance.com
06.05.1433-5946
On the end of the BPS6 port tube there is a tether.
The tether will be used later to guide the BPS6 port
tube through the mounting platform opening.
Position end of port tube as close as possible
to back of mounting platform. Loop tether into
the anchored zip tie and secure. This process
ensures that bandpass connector is easily
attached later and other tradespersons won’t
infringe on port tube assembly area.
5 6
7 8
Tether into
zip tie
Tether
For wiring diagrams &
detailed eManual scan
the QR code or visit
www.sonance.com/
in-wall-in-ceiling/
architectural-series
Secure the wires with a zip tie near the
terminals to prevent accidental removal by
another tradesperson.
Attach the from the four conductor wires
amplifier to the input terminals on the end of
the BPS6. Positive wires to red terminals and
negative wires to black terminals. Run the
speakers wires to amplifier location and run
signal test with 9V battery. NOTE: Port tube
contains foam plug with tether, make sure
pressure levels don’t expel the foam and
tether. Do not connect the voice coils
in parallel.
Produktspezifikationen
| Marke: | Sonance |
| Kategorie: | Subwoofer |
| Modell: | Bandpass BPS6 |
Brauchst du Hilfe?
Wenn Sie Hilfe mit Sonance Bandpass BPS6 benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten
Bedienungsanleitung Subwoofer Sonance
15 Juni 2025
12 September 2024
1 September 2024
1 September 2024
9 August 2024
29 Juli 2024
6 Juli 2024
6 Juli 2024
9 Mai 2024
17 Februar 2024
Bedienungsanleitung Subwoofer
- Stinger
- Lanzar
- Match
- Cerwin-Vega
- Triangle
- PrecisionPower
- Mission
- Harman Kardon
- Power Dynamics
- Helix
- MB Quart
- Adam
- LD Systems
- Paradigm
- TCL
Neueste Bedienungsanleitung für -Kategorien-
13 Juni 2025
13 Juni 2025
12 Juni 2025
11 Juni 2025
11 Juni 2025
11 Juni 2025
11 Juni 2025
11 Juni 2025
10 Juni 2025
10 Juni 2025