Sonic Alert HA360SSBC Bedienungsanleitung
Sonic Alert
Sicherheit
HA360SSBC
Lies die bedienungsanleitung für Sonic Alert HA360SSBC (2 Seiten) kostenlos online; sie gehört zur Kategorie Sicherheit. Dieses Handbuch wurde von 25 Personen als hilfreich bewertet und erhielt im Schnitt 4.6 Sterne aus 13 Bewertungen. Hast du eine Frage zu Sonic Alert HA360SSBC oder möchtest du andere Nutzer dieses Produkts befragen? Stelle eine Frage
Seite 1/2
INSTALLATION AND SET UP FOR HOMEAWARE™ TRANSMITTER
HA360SSBC – Baby Cry
The HomeAware™ HA360SSBC transmitter is
designed to alert you to the sound of a baby crying.
This transmitter alerts you through the HomeAware™
Main unit and remote receivers located in other rooms.
Battery Backup Installation
Install a new 9 volt alkaline battery into the battery
compartment located on the back of the unit. See
diagram for battery door location. Battery backup will
provide power when a power outage has occurred.
Power will be provided for a continuous outage lasting
7 days, or for short outages up to two years.
Link Button Set Up
This procedure will link the HA360SSBC – Baby Cry to
your Main unit. The Main unit will also provide an alert
to all HomeAware™ remote receivers. When using the
Bridge unit HA360BU all original Sonic Alert receivers
(SA101, SA201, BL300, and SB1000) will also alert
you.
It is best to do the link procedure in the same room with
the HomeAware™ Main unit, make sure the unit is
plugged in.
To link a transmitter to your HomeAware™ Main
unit:
1. Press set up button and the word LINK will be
shown on the display, press Enter. LINK will begin
blinking. (If LINK mode is entered by accident,
simply press the BACK button to exit and return to
the clock.)
2. Press and hold down the Link button on the back of
your transmitter for about 1 second. The red LED
on the transmitter will light up. Release the button.
3. Upon successful connection, the red LED on the
transmitter will flash 2 times, then turn off. The
HomeAware™ main unit will briefly show DONE,
and return to the time display. Your transmitter is
now connected and ready to test and use.
Sensitivity Switch
You can adjust the sensitivity of the Baby Cry detector.
There are three levels to choose from: The HI setting is
the most sensitive setting and will alert you to more
sounds. Moving this switch to MED makes it less
sensitive and will alert you to less sound. The LO
setting is the least sensitive. If you are not picking up
the sound you need to be alerted to, simply move the
sensitivity switch to a higher setting. If you have set this
setting to HI and you are still not picking up the sound
try moving the transmitter closer to the sound.
When a sound is detected it will send a signal to the
HomeAware™ base unit and all HomeAware™ remote
receivers, also the red LED light will flash on the front
of the unit.
Low Voltage Input
HomeAware™ transmitters have a low 120 volt AC
power supply that powers the HA360ss. Simply plug
the unit into any 120 volt AC power outlet. Next plug
the other end into the Low Voltage Input located on the
side, see diagram below.
FCC Requirements
This device complies with part 15 of the FCC rules.
Operation is subject to the following two conditions; (1)
This device might not cause harmful interference, and
(2) this device must accept any interference received,
including interference that may cause undesired
operation.
Produktspezifikationen
| Marke: | Sonic Alert |
| Kategorie: | Sicherheit |
| Modell: | HA360SSBC |
Brauchst du Hilfe?
Wenn Sie Hilfe mit Sonic Alert HA360SSBC benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten
Bedienungsanleitung Sicherheit Sonic Alert
23 August 2024
22 August 2024
22 August 2024
22 August 2024
18 August 2024
18 August 2024
17 August 2024
12 August 2024
10 August 2024
10 August 2024
Bedienungsanleitung Sicherheit
- Basetech
- ME
- MarQuant
- Home Protector
- Ajax
- Voxx
- Kocom
- Smanos
- Foscam
- SmartHome
- Friedland
- Stobo
- Xavax
- Guardall
- Powermax
Neueste Bedienungsanleitung für -Kategorien-
5 Oktober 2024
24 September 2024
20 September 2024
19 September 2024
17 September 2024
17 September 2024
16 September 2024
16 September 2024
27 August 2024
27 August 2024