StarTech.com PEX4M2E1 Bedienungsanleitung

Lies die bedienungsanleitung für StarTech.com PEX4M2E1 (2 Seiten) kostenlos online; sie gehört zur Kategorie Regler. Dieses Handbuch wurde von 25 Personen als hilfreich bewertet und erhielt im Schnitt 4.0 Sterne aus 3 Bewertungen. Hast du eine Frage zu StarTech.com PEX4M2E1 oder möchtest du andere Nutzer dieses Produkts befragen? Stelle eine Frage

Quick start guide

FR: Guide de l’utilisateur - fr.startech.com

DE: Bedienungsanleitung - de.startech.com

ES: Guía del usuario - es.startech.com

NL: Gebruiksaanwijzing - nl.startech.com

PT: Guia do usuário - pt.startech.com

IT: Guida per l’uso - it.startech.com

Manual Revision: 09/10/2019

For the latest information, technical specications, and support for

this product, please visit www.startech.com/PEX4M2E1.

Packaging contents

• 1 x PCI Express® adapter card to M.2 NVMe PCIe SSD

• 1 x low-prole bracket

• 1 x full-prole bracket (pre-installed)

• 1 x SSD stando and installation screw

• 1 x quick start guide

System requirements

• PCI Express M.2 NGFF SSD

• Computer system with a p1-x4 or larger slot

• Phillips head screwdriver

• Small set of pliers

The PEX4M2E1 is OS independent and doesn’t require any additional

drivers or software.

Note: Some drives are not compatible with certain operating

systems. Before you install a drive in the adapter, check with the

drive manufacturer to make sure that the drive is compatible with

the OS that your computer system is running.

System requirements are subject to change. For the latest

requirements, please visit www.startech.com/PEX4M2E1.

PEX4M2E1

x4 PCIe Expansion Card to M.2 PCIe SSD Adapter

*actual product may vary from photos

Product diagram

Mounting bracket

(full-prole bracket pictured)

SSD stando and

installation screw

PCIe p1-x4

connector

Drive installation holes

M.2 NGFF connector

Install a drive in the adapter

Warning! Drives and adapters should be handled carefully,

especially when they’re transported. If you’re not careful with your

drives, you may lose data as a result. Always handle storage devices

with caution. Make sure that you’re properly grounded by wearing

an anti-static strap when you install any computer component. If an

anti-static strap isn’t available, touch a large grounded metal surface

for several seconds to discharge any built-up static electricity.

1. Depending on the length of the drive that you want to install, you

may need to move the preinstalled SSD stando and installation

screw. Place your drive next to the adapter and note the drive

installation hole that matches the height of your drive. If the SSD

stando and installation screw are already installed in the correct

position, proceed to step 6.

2. On the back of the PEX4M2E1, use a small set of pliers to remove

the nut that is holding the SSD stando and installation screw in

place.

3. On the front of the adapter, remove the SSD stando and

installation screw.

4. Place the SSD stando in the drive installation hole that matches

the length of your drive.

5. Replace the nut that you removed in step 2 and tighten it in place.

6. Gently slide the M.2 connector on the drive into the

corresponding connector on the adapter and press the drive

down toward the adapter until the drive is in place.

Note:The connector on your drive is keyed so that it only ts in the

adapter one way.

7. Insert the installation screw into the SSD stando and tighten it

into place.

Install the low-prole bracket

The PEX4M2E1 can be mounted in both low-prole and full-prole

computer systems. The full-prole bracket comes preinstalled in the

adapter but you can install the low-prole bracket instead.

1. Use a Phillips head screwdriver to remove the two bracket screws

from the PEX4M2E1.

2. Remove the full-prole bracket from the adapter.

3. Line up the low-prole bracket with the bracket holes on the back

of the adapter.

4. Insert the two bracket screws you removed in step 1 and tighten

them in place.

Bracket

screws

Install the adapter in a computer

1. Turn o the computer that you want to install the PEX4M2E1 into.

2. Remove the case from your computer. For more information

about how to properly do this, consult the documentation that

came with your computer system.

3. Place the adapter into an available expansion slot.

4. Insert a computer case screw (not included) into the case-

Produktspezifikationen