Sunding SD-589 Bedienungsanleitung
Sunding
Nicht kategorisiert
SD-589
Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Sunding SD-589 (2 Seiten) in der Kategorie Nicht kategorisiert. Dieser Bedienungsanleitung war für 3 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet
Seite 1/2
Computer Battery Installation
SD-589 (19 Function)
Setting(km)/(mile)
Bicycle Computer Instruction Manual V1.0
Installation of Speedometer
- SPD Current Speed
- ODO Odometer (0~99999km/m)
- DST Trip Distance
- MXS Maximum Speed
- AVS Average Speed
- TM Elapsed Time
- CLK Clock (12H/24H)
- TMP Temperature / (-10°C~70°C)
- SCAN
- “+”“-”Comparator
- SETTING TYRE CIRCUMFERENCE / (0mm~9999mm)
- SETTING SPEED SCALE (km,m)
- MAINTENANCE ALERT
- SETTING THE LAST VALUE OF ODOMETER / ODO
- COMPUTER LOW BATTERY INDICATOR
- WIRELESS WAKE UP
- AUTO BACKLIGHT
- BACKLIGHT IS LONG BRIGHT
- AUTO ON/OFF
Functions
Installation
Parameter Settings
Wheel Size Input
3~5mm
Notice
The magnet is designed for spokes
that are less than 2mm thick.
Pass bicycle spokes through the
plastic hole on the bottom of the
magnet and tighten to secure
Mounting Shoe \ Computer
TIRE SIZE
CIRC
TIRE SIZE
CIRC
TIRE SIZE
CIRC
12×1.75 935
12×1.95 940
14×1.50 1020
14×1.75 1055
16×1.50 1185
16×1.75 1195
16×2.00 1245
16×1-1/8 1290
16×1-3/8 1300
17×1-1/4 1340
18×1.50 1340
18×1.75 1350
20×1.25 1450
20×1.35 1460
20×1.50 1490
20×1.75 1515
20×1.95 1565
22×1-3/8 1770
22×1-1/2 1785
24×1.75 1890
24×2.00 1925
24×2.125 1965
24×1(520) 1753
24×/34Tubular 1785
24×1-1/8 1795
24×1-1/4 1905
26×1(599) 1913
26×1.25 1950
26×1.40 2005
26×1.50 2010
26×1.75 2023
26×1.95 2050
26×2.10 2068
26×2.25 2070
26×2.35 2083
26×3.00 2170
26×1-1/8 1970
26×1-3/8 2068
26×1-1/2 2100
26×7/8 1920
650×20C 1938
650×23C 1944
650×25C 1952
650×38A 2125
650×38B 2105
27×1(630) 2145
27×1-1/8 2155
27×1-1/4 2161
27×1-3/8 2169
27.5×1.50 2079
27.5×1.95 2090
27.5×2.1 2148
27.5×1.25 2182
700×18C 2070
700×19C 2080
700×20C 2086
700×23C 2096
700×25C 2105
700×28C 2036
700×30C 2146
700×32C 2155
700Tubular 2130
700×35C 2168
700×38C 2180
700×40C 2200
700×42C 2224
700×44C 2235
700×45C 2242
700×47C 2268
29×2.1 2288
29×2.2 2298
29×2.3 2326
MODE
SET
MODE
Wired Remote Control
Button Function Description
3
4
Insert the threaded strap through
the locking hole and tighten via
the included nut.
Cut off excessive strap
1
2
Align the computer unit and
rotate it to lock into the
mount base.
Attach the mount base
onto the handlebar at
the desired location.
Top View:
Align the
computer unit as
showed then
rotate clockwise
To install the battery, make sure the positive (+) pole
faces the battery cover and then put the cover back
on and tighten with a coin or flat head screw driver.
If the LCD shows strange figures, take out the
battery and put it back in.
Attach speedometer sensor to the front fork using the ties. The
computer and sensor should be installed on the same side of the
fork, with distance between them of less than 60cm. The arrow
on the sensor should point at the magnet. Install magnet as
shown in figure. Distance between sensor and magnet should
be 3~5mm.
Computer
Sensor
Magnet
60CM
To check if the speed function and
sensor alignment are working
properly, spin the front wheel with the
computer in speed mode. Adjust the
position of sensor and magnet if there
is no or weak signal.
Reinstall the battery or press the MODE key +
SET key for 4 seconds at the same time. After
the screen is fully displayed, release the key,
and the screen will display 2060 with 1 digit
blinking.Refer to the table below to select your desired
circumference, press MODE key to change the flashing value,
press SET key to confirm, and move on to set the next digit.
Input circumference range is 0 9999mm. Keep pressing SET ～
key to enter kilometers/miles unit setting.
Press the button to choose betweenMODE
km (kilometer) or m (mile).
Press the button to enter MAINTENANCE SET
ALERTsetting.
Setting the Last value of Odometer
Sleep Mode
Maximum Speed (MXS)
Speedometer
Odometer
Trip Distance (DST)
Scan
Malfunction
Problems
No speed reading
Incorrect magnet / sensor alignment.
Inaccurate value is
indicated
Improper input, such as wheel
circumference.
Slow display response
Temperature exceeds operating limits
(0°C~55°C).
Black display
Temperature too high, or placed in
direct sunlight for too long. Let the unit
cool down.
Weak display
Poor battery contact or dead battery.
Display shows irregular
figures
Take out battery and re-install after 10
seconds.
Backlight long Bright
Auto Backlight
Function Descriptions
Malfunctions and Problems
Accessories
Trip Time
Speed Comparator
CLK Mode(12H/24H)
Setting Maintenance alert
Temperature (TMP)
Sensor
Mounting Shoe
Cable Ties
Wheel Magnet
CR2032 Battery
Computer
Average Speed (AVS)
Clear Data
Temperature Unit SettIng
Deep Sleep Setting
Deep Sleep Mode
Max speed in a single trip (DST)
Press the button to enter MODE AVS mode.
This is the single trip mode. Shows the
distance from the last data reset.
Counting range: 0.01 9999KM/M, It will～
automatically reset to 0 after exceeding.
Press the button to enter mode.MODE MXS
The odometer shows the total mileage from the last
reset to the present, The total mileage counting range
is 0 99999KM(Mile), It will automatically reset to 0～
after exceeding.
Press the button to enter mode.MODE DST
During riding, ‘ ’ and ‘ ’ indicates the current speed
is higher or lower than the average speed (AVS).
The speed is always displayed on the screen, with a maximum
reading of 99.9km/h(mile/h) and an accuracy of +/- 0.1 km/h
(mile/h).
Press and hold the mode key for 4 seconds to turn on
Backlight long Bright. Press and hold the mode key for 4
seconds and the Backlight long Bright will turn off. After the
computer enters the sleep mode the Backlight long Bright is
turned off.
In DST MXS AVS TM SCAN mode, hold button \ \ \ \ SET
4 seconds DST MXS AVS TM to clear all data.\ \ \
Press and hold key for 4 seconds in temperature display mode SET
to switch to Fahrenheit ( F). The temperature unit defaults to °
Celsius ( C).°
To set the value, press and hold button ODO SET
for 4 seconds in mode. The default value is ODO
0000.0. Press button to change the flashing MODE
figure, and button to confirm and move on to the next figure. SET
NOTE: Before replacing the battery, write down your mileage
and then reenter it after the battery is replaced.
To enter setting in the clock mode, press and hold
SET 12/24 buttonfor 4 seconds to enter H format
setting. Press it again to switch formats. Press SET
button to set Hour, and press button to change MODE
the flashing hour figure. Press button one more time to set SET
Minute, and press button to change the flashing minute figure. MODE
Press button to confirm and press it once more to go back to SET
ODO mode.
To set the maintenance alert, press the MODE
button to choose from 200/400/600/800 km/mile
while the default value of 200km/mile flashes. Press
the button to confirm and go to Clock mode.SET
(When the reaches the maintenance alertODO
value you set, symbol will show up on the
screen to remind you. Press both button andSET
button to clear it.)MODE
The Smart Backlight will activate when there is insufficient light.
Press any button to turn on the Backlight for 5 seconds.
The screen displays SLEEP. In deep sleep mode, the
only way to wake up the computer is to press any key.
CLK clock is retained. When there is a signal
input or key press computer will return to the mode before
sleep, and remember the values before sleep.
It displays DST, MXS, AVS, and TM in
turn for four seconds per mode.
Press the button to enter Mode.MODE CLOCK
measures and displays the external
environment temperature, which defaults
to Celsius (°C), with a temperature
measurement range of -10°C~70°C.
Press the button to enter Mode.MODE SCAN
The cumulative riding time for a singletrip (DST).
Timing range: 0:00:00~9:59:59, it will reset to
zero and recount after exceeding.
Press the button to enter Mode.MODE TMP
Average speed in a single trip (DST)
Press the button to enter mode.MODE TM
Press and hold key + key for seconds, after the screen MODE SET 6
displays , computer will enter deep sleep mode, The computer SLEEP
unit will automatically enter deep sleep mode if there is no operation
within days.7
Produktspezifikationen
| Marke: | Sunding |
| Kategorie: | Nicht kategorisiert |
| Modell: | SD-589 |
Brauchst du Hilfe?
Wenn Sie Hilfe mit Sunding SD-589 benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten
Bedienungsanleitung Nicht kategorisiert Sunding
7 Juni 2025
6 Juni 2025
6 Juni 2025
6 Juni 2025
6 Juni 2025
6 Juni 2025
6 Juni 2025
6 Juni 2025
6 Juni 2025
6 Juni 2025
Bedienungsanleitung Nicht kategorisiert
- Nicht kategorisiert Astro
- Nicht kategorisiert Suzuki
- Nicht kategorisiert BeeSecure
- Nicht kategorisiert HQ
- Nicht kategorisiert Legamaster
- Nicht kategorisiert Blackmagic Design
- Nicht kategorisiert Prixton
- Nicht kategorisiert Metabo
- Nicht kategorisiert Visage
- Nicht kategorisiert Barska
- Nicht kategorisiert Alpha Tools
- Nicht kategorisiert Edge Products
- Nicht kategorisiert Autel
- Nicht kategorisiert Trigano
- Nicht kategorisiert Delta
Neueste Bedienungsanleitung für -Kategorien-
7 Juni 2025
7 Juni 2025
7 Juni 2025
7 Juni 2025
7 Juni 2025
7 Juni 2025
7 Juni 2025
7 Juni 2025
7 Juni 2025
7 Juni 2025