Tado Wireless Temperature Sensor Bedienungsanleitung
Tado
Thermostat
Wireless Temperature Sensor
Lies die bedienungsanleitung für Tado Wireless Temperature Sensor (8 Seiten) kostenlos online; sie gehört zur Kategorie Thermostat. Dieses Handbuch wurde von 19 Personen als hilfreich bewertet und erhielt im Schnitt 3.6 Sterne aus 10 Bewertungen. Hast du eine Frage zu Tado Wireless Temperature Sensor oder möchtest du andere Nutzer dieses Produkts befragen? Stelle eine Frage
Seite 1/8
Manual for Professional
Installers
DIY Installation
If you are a professional installer, please not download the tado˚ app. There you will find specific installation instructions.
This manual is meant exclusively for professional installers. It includes generic instructions to install the Wireless
Receiver (Programmer) and the Wireless Temperature Sensor.
For the Starter Kit - Wireless Smart Thermostat V3+
(Incl. Programmer with Hot Water Control)
Manual version 3.2
A. Remove the battery
protection strip.
B. Press the button for
3 sec to start pairing.
C. Pairing may take up
to 2 min.
D. The static icon below
indicates successful pairing.
If pairing fails (E0), make sure the distance between the devices is approximately 3 meters. Pair again by pressing the
button for 3 sec.
2. Pair the Wireless Temp. Sensor
1. Install the Internet Bridge
A. Connect the Internet Bridge to the router.
If no free USB port is available on the router, use the
included 5V power adapter.
B. Press and hold the pairing button until the pairing LED
starts blinking.
2
min
3
sec
Solid on
Blinking
Unfold to check:
Step 4: Wire the Wireless Receiver
Step 5: Pair the Wireless Receiver
Step 6: Configuration
Extra information: Wireless Receiver Symbols
Power supply, testing
mode & configuration
Connection with
other tado˚ devices
Device errors Heat request Hot water request
If there is a wired room thermostat installed in the zone that is intended to be controlled by the Wireless Receiver,
please by bridging the control wires and insulating the other wires with the included 2-terminal decommission it
connector blocks as shown in the images.
Once tado° is installed, the Wireless Receiver will be the only device that controls the heating system.
For Neutral and Earth, Insert only one wire per block, even though the block has more than one opening.
3. Replace the room thermostat
LIVE
(COM) NEUTRAL EARTH
SWITCHED
LIVE (NO)
Caution! Turn OFF the
power before wiring!
Produktspezifikationen
| Marke: | Tado |
| Kategorie: | Thermostat |
| Modell: | Wireless Temperature Sensor |
Brauchst du Hilfe?
Wenn Sie Hilfe mit Tado Wireless Temperature Sensor benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten
Bedienungsanleitung Thermostat Tado
23 September 2024
5 August 2024
19 Juli 2024
Bedienungsanleitung Thermostat
- Itho Daalderop
- Noma
- Fenix
- Profile
- Wallair
- Ecobee
- Essent
- Avidsen
- Nefit
- Agpo Ferroli
- Innogy
- OJ ELECTRONICS
- Busch-Jaeger
- King
- EnerGenie
Neueste Bedienungsanleitung für -Kategorien-
16 Juni 2025
15 Juni 2025
14 Juni 2025
14 Juni 2025
12 Juni 2025
12 Juni 2025
12 Juni 2025
8 Juni 2025
8 Juni 2025
8 Juni 2025