Tennsco J1878A-N Bedienungsanleitung
Lesen Sie kostenlos die đ deutsche Bedienungsanleitung fĂźr Tennsco J1878A-N (4 Seiten) in der Kategorie Schrank. Dieser Bedienungsanleitung war fĂźr 2 Personen hilfreich und wurde von 1.5 Benutzern mit durchschnittlich 5.0 Sternen bewertet
Seite 1/4
PK-1150918
ASSEMBLY INSTRUCTIONS & PARTS MANUAL
RETAIN INSTRUCTIONS FOR FUTURE REFERENCE
Jumbo Storage Cabinet
Unassembled Model J1878A-N
Tennsco LLC., Dickson, TN 37056-1888 ⢠(866) 446-8686
GENERAL SAFETY INFORMATION
Some parts may have sharp edges. CARE must be taken when handling various pieces to avoid injury.
For safety, wear a pair of work gloves when assembling or performing any maintenance on the units.
LIMITED WARRANTY
Tennsco warrants goods purchased hereunder to be free of defects in materials and workmanship for a period of one (1) year from the date of shipment, hereunder. This warranty shall not apply
in the event goods are damaged as a result of misuse, abuse, neglect, accident, improper application, modiîcation or repair by persons not authorized by Seller, where goods are damaged during
shipment, or where the date stamps on the goods have been defaced, modiîed or removed. UNLESS CONSIDERED UNENFORCEABLE OR UNLAWFUL UNDER APPLICABLE LAW:
a. ALL IMPLIED WARRANTIES, INCLUDING BUT NOT LIMITED TO WARRANTIES OR MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE HEREBY EXCLUDED:
b. BUYERS REMEDY, IF ANY, FOR ANY DEFECTIVE GOODS SHALL BE LIMITED TO A REFUND BY SELLER OR REPLACEMENT OF THE GOODS AT SELLERâS OPTION, AND SHALL IN NO
EVENT INCLUDE DAMAGES OF ANY KIND, WHETHER INCIDENTAL, CONSEQUENTIAL OR OTHERWISE.
NO GOODS ACCEPTED FOR RETURN WITHOUT PRIOR APPROVAL. Seller shall have the right to inspect any goods claimed to be defective at Buyers place of business or require Buyer to return the
goods to Seller for inspection on Sellerâs premises. Transportation charges covering returned goods will be borne by Seller only if such goods are proven to be defective, are covered by this warranty
and are returned within the warranty period stated above.
LOAD CAPACITIES PER SHELF LEVEL
48w x 18d
400 lbs.
UNIT SIZE
WEIGHT CAPACITY
EVENLY DISTRIBUTED
ASSEMBLY OF J1878A-N CABINET
Tools Needed: A free
11
/ â nut driver is included with each Tennsco cabinet. 32
Two people are recommended for assembly. Approximate assembly time: 30-40 minutes.
2. Place the 2-piece cabinet back (Ref.
No. 1) on a protected surface to
prevent scratching the paint.
The îange on the
bottom of the back
should be facing upward.
Bolt the back panels together with
seven bolts and nuts (Ref Nos. 17 & 18).
1. The reference numbers used throughout this sheet refer
to the illustration on the back cover. This is to help you
to identify the various parts as they are mentioned.
3. Attach the left side (Ref. No. 2) to the back by placing
îange (A) around the back and bolting together with
seven bolts and nuts. Be sure that the lances on all
shelf adjustment strips (B) point in the same direction.
6. Attach the sill (Ref. No. 8) to the sides. Place nuts loosely on each
of the studs and slide the ends of the sill into the slots on both
sides of the unit. Then, securely tighten the nuts.
4. Attach the top (Ref. No. 5) to the unit by sliding the outer
îange over the back of the unit and the side îange on
the top over the side panel. The
threaded studs should go
through the holes in the
top îange of the
side and
fasten with
three nuts.
Attach the
back to the
top using four
bolts and nuts.
7. Place the rear îange of one of the shelves (Ref. No. 4) into the
four bottom lances of the back. The front of the shelf will rest
on the sill.
All lances point UP on
both backs and side.
Flange goes
under back.
Flange faces upward.
Flanges
face upward
Threaded studs go
through the holes
in the ďŹange at the
top of the side.
Slide ends in to the slots
on the bottom of the sides.
Nuts placed loosely
on studs of the sill.
Insert bottom into
bottom lances.
B
A
NOTE: When bolting the unit together, leave
the bolts slightly loose until Step 8, unless
otherwise speciďŹed.
5. Attach the right side (Ref. No. 3) to the back in the same manner
as you did in step 3, again, making sure that the îange is
around the back and that the lances on the shelf adjustment
strips are pointed in the same direction as those on the back and
left side. Push the side panel up so the studs in the top go
through the holes in the top
îange of the side and
fasten with three
nuts as in
step 4).
8. Set the unit upright and tighten
all nuts around the entire unit.
10. Attach the left door
(Ref. No. 6) to the
unit by placing the
door on the hinges,
aligning the hinge
holes, and dropping
the hinge pins (Ref.
No. 15) into the slots.
Then, tap the top of
each hinge pin until
fully seated.
Leveler
Access Holes
9. Insert the four remaining shelves
at your desired levels.
NOTE: In order to place the
shelves, you must ďŹrst tilt the
shelf slightly to the left or right
before inserting into the unit.
12. The cabinet must be
level in order for the
doors to close
properly. Levelers
may be adjusted by
placing the nut driver
through the hole in
each end of the sill
and adjusting the
leveling screw.
11. Attach the right door
(Ref. No. 7) to the unit
in the same way you
attached the left door.
1. Place the locking handle
(Ref. No. 10) on the right
hand door and fasten with
two #8-32 X
1
/ 4hex-head
bolts and lock washers,
provided with the handle.
4. Slide the nylon lock bar
guide inserts (Ref. No.
13) over the lock bar
ends and through the
door slots (see âBâ at
right). Push down îrmly
until the guides snap
into place.
5. Attach the âdummyâ handle
(Ref. No. 14) using two
#8-32 X
1
/ 4hex-head bolts
and lock washers.
Handle/Locking System Installation
A
B
B
2. Turn the handle to the
open position and
place the locking cam
(Ref. No. 11) over the
square shank of the
door handle. The latch
must be facing downward
as shown. Then place the
locking cotter pin (Ref. No.
12) through the hole of the
square shank.
3. With the handle still in the open position, hook the
locking bars (Ref. No. 9) to the locking cam (see
âAâ at left). Once in position, slowly rotate the door
handle to the closed position so the lock bars
prot rude from the holes at the top and bottom
of the door (shown at right, below).
Produktspezifikationen
| Marke: | Tennsco |
| Kategorie: | Schrank |
| Modell: | J1878A-N |
Brauchst du Hilfe?
Wenn Sie Hilfe mit Tennsco J1878A-N benĂśtigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten
Bedienungsanleitung Schrank Tennsco
7 Juni 2025
7 Juni 2025
7 Juni 2025
7 Juni 2025
7 Juni 2025
7 Juni 2025
7 Juni 2025
7 Juni 2025
7 Juni 2025
7 Juni 2025
Bedienungsanleitung Schrank
- Schrank Bbf
- Schrank APC
- Schrank Handson
- Schrank Talgø
- Schrank Bush
- Schrank WOOOD
- Schrank Urrea
- Schrank Miomare
- Schrank IKEA
- Schrank Livarno
- Schrank Tvilum
- Schrank Sencys
- Schrank JYSK
- Schrank StarTech.com
- Schrank Ordex
Neueste Bedienungsanleitung fĂźr -Kategorien-
4 Juni 2025
4 Juni 2025
4 Juni 2025
4 Juni 2025
4 Juni 2025
4 Juni 2025
4 Juni 2025
1 Juni 2025
3 Dezember 2024