Valeton VLP-400 Bedienungsanleitung

Lies die bedienungsanleitung für Valeton VLP-400 (1 Seiten) kostenlos online; sie gehört zur Kategorie Nicht kategorisiert. Dieses Handbuch wurde von 9 Personen als hilfreich bewertet und erhielt im Schnitt 4.9 Sterne aus 5 Bewertungen. Hast du eine Frage zu Valeton VLP-400 oder möchtest du andere Nutzer dieses Produkts befragen? Stelle eine Frage

12

1314

15

16

17

18

8. [LOOP 1] Footswitch

Controls the record, play, stop, overdub, undo and redo functions of LOOP 1:

For blank loop: Record→Play→Overdub

For loop with recordings: Play→Overdub

When playing or overdubbing: Press and hold this footswitch for 2 seconds or more to perform undo (cancel

recording or the last overdub recording). Press and hold the Footswitch again to perform the redo function

(cancel the undo operation).

9[LOOP 2] Footswitch.

Control the recording, playback, stop, overdub recording, undo and redo functions of LOOP 2, the operation logic

is consistent with [LOOP 1] Footswitch.

10[DRUM] Footswitch.

Controls the on/off of the drum machine, and long press to enter the Tap Tempo state to adjust the BPM of the

rhythm.

11. [ASSIGNALE] Footswitch

This pedal can be assigned various effects applied to the LOOP track. Double pressing can play and stop two

LOOPs and the drum at the same time. Long press can select any LOOP for "STACK" overdub recording.

12.INPUT (L/R) Jack

-L/MIC: Use XLR/TS mono jack to connect guitar, bass, dynamic microphone or pedals.

-R: 1/4" (6.35mm) mono jack to connect guitar, bass or pedals.

13. OUTPUT (L/R) Jack

1/4" (6.35mm) unbalanced output interface, connect to speaker, mixer or recording equipment.

Mono input: Only L or R channel input, OUTPUT L and R output the same LOOP signal (dual mono output).

Stereo input: When INPUT L and R are input at the same time, OUTPUT L and R output the LOOP signal of the

corresponding input channel.

*Note: When INPUT L and R are inserted at the same time, if only one channel of L or R has signal input, only the

corresponding output channel has LOOP signal output.

14. CTRL 1, 2 Jack

The 1/4" (6.35mm) TRS jack is used to connect an external dual footswitch, and the CTRL function can be assigned.

15. MIDI (IN/OUT) Jack

Connect an external MIDI device here.

16. USB Jack

By connecting to a Mac or PC through the USB 2.0 Type-C port, import and export projects and update

firmware with supporting software.

17. DC 9V Jack

Power Requirements: DC 9V,500mA, .

18. PHONES

1/8" (3.5mm) TRS stereo interface, connected to headphones to monitor the output of the device.

Basic Tutorial for LOOP 1 and 2

1

2

3

4

5

6

7

891011

1. [LEVEL] LOOP 1, LOOP 2, DRUM

Controls the playback volume of LOOP 1, LOOP 2 and drum.

2. [SERIAL/FREE] Toggle switch

Used to select the coordination mode of LOOP 1 and LOOP 2:

SERIAL: LOOP 1 and LOOP 2 play alternately.

FREE: LOOP 1 and LOOP 2 can be played at the same time.

3. [MEMORY/SAVE] Knob (with enter button)

Select and recall the project by turn the knob, press to save the

LOOP project, and long press the knob to select the external

pedal function.

4. Display

Displays information such as project number, drum rhythm pattern number, and BPM.

5. [DRUM/BPM] Knob (with enter button)

Turn to select the drum rhythm pattern or djust the BPM of drum machine, press the knob to switch the current

adjustment object (RHY or BPM).

6.[AUTO/SYNC] Toggle switch

Drum machine mode to select AUTO or SYNC:

AUTO: Automatically detects and sets the drum machine BPM based on the recording.

SYNC: The drum machine will play according to the currently set BPM.

7. [ASSIGN] Knob

Used to select the function enabled by the “ASSIGNABLE” footswitch:

OCTAVE: Make the track have a lower octave effect REVERSE: Play the track in reverse

FREEZE: Make the notes at a certain moment of the track form an infinite sustain

HALF: Make the track play at 1/2 the previous speed FADE: Smooth volume decay for recording tracks

ONCE: Make the track play once and then stop SOLO: Make one of the two LOOPs play alone

Panel IntroductionSpecification

Maximum recording storage: about 12 hours

Number of tracks: 2

Input Impedance:1MΩ/4.7kΩ

Output Impedance:4.7kΩ

AD/DA: 32-bit, 48kHz

Recording format:

WAV (32-bit Float, 48kHz, stereo)

Maximum project saving: 99

Drum rhythm: 100 or more

Weight: 1295g

Dimensions:

253mm (D) X 165.3mm (W) X 58mm(H)

Record, Play, Overdub and Delete

“Bottom track”: The first recorded track of a blank LOOP.

“Overdub”: Overlay the second and subsequent recordings on top of the bottom track.

“Stop”: Press twice to stop the LOOP only active when the LOOP is playing.

“Delete“: When there is only the bottom track recorded, a long press during playback will directly

delete the base track. If the recording includes overdubs, you can use a combination of (single

press + long press) to quickly delete the entire track.

Perss

Recording

Bottom track

Perss

Play

Perss

Overdub

Press

Twice

Stop

Delete LOOP

Perss

Play

Perss

Play

Hold

Undo and Redo

“Undo”: Hold to Undo is only for the last overdub track, not for the bottom track.

Overdub

Perss

Play

HoldHold

Undo and the

track goes on

Undo and the

track goes on

Recording length tips

The length of each overdub track of LOOP 1 or 2 can be controlled as an integer multiple of the

length of its own current track.

Example 1: Press the footswitch before the first loop playback ends and wait for the recording to

end automatically.

Example 2: Press the footswitch before the third loop playback ends to overdub 1, with a duration

of three times the current loop length. Then, press the footswitch before the second loop playback

ends to overdub 2, with a duration of two times the current loop length.

Produktspezifikationen