Vitek VT-3582 BK Bedienungsanleitung

Vitek Radio VT-3582 BK

Lies die bedienungsanleitung für Vitek VT-3582 BK (2 Seiten) kostenlos online; sie gehört zur Kategorie Radio. Dieses Handbuch wurde von 34 Personen als hilfreich bewertet und erhielt im Schnitt 4.8 Sterne aus 17.5 Bewertungen. Hast du eine Frage zu Vitek VT-3582 BK oder möchtest du andere Nutzer dieses Produkts befragen? Stelle eine Frage

Download PDF

Seite 1/2

HIGH OUTPUT LED TAPE

Installation Guide

V2 .0

Caution: Please read this guide carefully before installing Lyyt LED tape

Damage caused by incorrect application is not covered by the warranty

Installation

Lyyt high output LED tape is supplied on 5m reels and operates from a 24Vdc power supply.

Installation should be carried out by competent electrical installers, observing the relevant electrical safety procedures.

The tape has a self-adhesive backing to allow it to be easily attached to a clean, non-porous surface.

Where less than 5m of tape is needed, there are solder points as shown below, where the tape may be cut to size. These

cut points will be at 5cm intervals. In order to re-connect to another length of tape after cutting, strip away the epoxy

coating at the solder points and solder a wire from “+” to “+” and a wire from “ ” to “ ” as shown below. - -

Some accessories are supplied with the tape reel for this purpose or alternatively, connection clips may also be used Lyyt

to join lengths of tape (156.135UK 156.140UK). In order to retain weather-proofing, it is advised to seal the cuts and –

joints with silicone glue.

Each 5m reel of single colour LED tape is fitted with a 2.1mm DC jack socket for power input for easy connection to a

power supply. This connector may be removed and stripped for bare wire connection if a 2.1mm jack is not fitted to the

power supply.

If the power supply has enough capacity to power more than one reel, another reel can be connected to the end of the

first reel via the 2.1mm DC jack plug.

For Lyyt high output LED tape, it is recommended to link no more than 15m of tape in sequence .

Using a separate wire to loop “+” and “ ” back to the power supply will help to avoid dimming at the far end through -

voltage drop.

To connect beyond these lengths, a parallel wire must be run from the power supply to the further reels of tape.

Produktspezifikationen

Marke:	Vitek
Kategorie:	Radio
Modell:	VT-3582 BK
Eingebaute Lautsprecher:	Ja
FM-Radio:	Ja
Kopfhörer-Anschluss:	3,5 mm
Breite:	235 mm
Tiefe:	63 mm
Gewicht:	862 g
Produktfarbe:	Schwarz
Höhe:	132 mm
Radiotyp:	Tragbar
Tunertyp:	Analog
Unterstützte Bänder:	FM,MW,SW
Digitales UKW-Radio:	87 - 108 MHz
RMS-Leistung:	3 W
Anzahl eingebauter Lautsprecher:	1
AC Eingangsfrequenz:	50 Hz
Kopfhörerausgänge:	1
Playback MP3:	Nein
Anzahl unterstützter Akkus/Batterien:	3
Akku-/Batteriespannung:	1.5 V
Ausgangsleistung:	350 mW
Eingangsspannung:	220 V
Stromeingang:	Ja
Apple-Docking-Kompatibilität:	Nicht unterstützt
Kompatible Akku-/Batteriegrößen:	D