Whirlpool ADG 6342 6S FD Bedienungsanleitung

Whirlpool Spülmaschine ADG 6342 6S FD

Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Whirlpool ADG 6342 6S FD (8 Seiten) in der Kategorie Spülmaschine. Dieser Bedienungsanleitung war für 5 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Download PDF

Seite 1/8

GB -1-

-1-

-1--1-

Chart

(see at right for

(see at right for (see at right for options desc

options desc

options descoptions description)

ription)

ription)ription)

PROGRAM SELECTION

PROGRAM SELECTION PROGRAM SELECTION

BUTTON

BUTTONBUTTON

Push “Programs” button

(repeatedly) until the indicator

of the required program lights

up (see “Table of programs”

below).

CANCEL/OFF BUTTON

CANCEL/OFF BUTTONCANCEL/OFF BUTTON

Push this button to switch off the control panel.

If pressed when a program is running it cancels the

program ongoing draining water for 1 minute.

If pressed when the dishwasher is switched off it

drains any possible liquids from dishwasher

(1 minute process).

If the indicator flashes repeatedly, see page 6 -

chapter ”What to do if...”.

STSTART/RESUME BUTTON

ART/RESUME BUTTON

ART/RESUME BUTTONART/RESUME BUTTON

Push this button to start the selected program: the

indicator lights up and goes off at the end of the

program. When the door is opened during a

washing cycle, the cycle is temporarily paused: the

Start indicator blinks.

To resume the cycle push the Start button and

close the door within 3 seconds.

1)1) Program data obtai

Program data obtai

Program data obtaiProgram data obtained in conformity with Eu

ned in conformity with Eu

ned in conformity with Euned in conformity with European standard

ropean standard

ropean standardropean standard EN 50242, obtained under norma

EN 50242, obtained under norma

EN 50242, obtained under norma EN 50242, obtained under normal conditions (without

l conditions (without

l conditions (withoutl conditions (without additional opt

additional opt

additional opt additional options) and ma

ions) and ma

ions) and maions) and may vary

y vary

y vary y vary

depending on conditi

depending on conditidepending on conditions. Differences

ons. Differences

ons. Differencesons. Differences of up to 20 minutes are poss

of up to 20 minutes are poss

of up to 20 minutes are poss of up to 20 minutes are possible with sensor

ible with sensor

ible with sensorible with sensor programs as a result of

programs as a result of

programs as a result of programs as a result of the appliance’s auto

the appliance’s auto

the appliance’s auto the appliance’s autom

mmatic calibrat

atic calibrat

atic calibratatic calibration system.

ion system.

ion system.ion system.

2)2) Referenc

Referenc

ReferencReference program fo

e program fo

e program foe program for energy label in

r energy label in

r energy label inr energy label in compliance

compliance

compliance compliance with EN 50242 r

with EN 50242 r

with EN 50242 r with EN 50242 regulations

egulations

egulationsegulations. - Note for T

. - Note for T

. - Note for T. - Note for T

esting Instit

esting Institesting Institutes: for deta

utes: for deta

utes: for detautes: for detailed infor

iled infor

iled inforiled information on the EN/Standard loadin

mation on the EN/Standard loadin

mation on the EN/Standard loadinmation on the EN/Standard loading

g g

comparison te

comparison tecomparison test and other t

st and other t

st and other tst and other tests, contact t

ests, contact t

ests, contact tests, contact the

he he followi

followi

followifollowing address: “nk

ng address: “nk

ng address: “nkng address: “nk_

__customer@whirlpool.com”.

customer@whirlpool.com”.

customer@whirlpool.com”.customer@whirlpool.com”.

3)3) T

TThe antibacterial action has been tes

he antibacterial action has been tes

he antibacterial action has been teshe antibacterial action has been tested by the Institut P

ted by the Institut P

ted by the Institut Pted by the Institut Pasteur of Lille (France), based

asteur of Lille (France), based

asteur of Lille (France), basedasteur of Lille (France), based on the NF EN 13697 standard of Nove

on the NF EN 13697 standard of Nove

on the NF EN 13697 standard of Nove on the NF EN 13697 standard of November 20

mber 20

mber 20mber 2001.

01.

01.01.

TTable of programs

able of programs

able of programsable of programs

Deter-

Deter-Deter-

gent

gentgent

Consumption

ConsumptionConsumption

Drying

DryingDrying

Phase

PhasePhase

PP Programs

Programs

ProgramsPrograms Avail

Avail

AvailAvailable

able

ableable

options

optionsoptions Loading instructions

Loading instructions

Loading instructionsLoading instructions

Litres

LitresLitres kWh

kWh

kWhkWh Minutes

Minutes

MinutesMinutes 1)

1)1)

Auto Sensor

Auto Sensor Auto Sensor 50°- 65°C

50°- 65°C

50°- 65°C50°- 65°C

Delay

Antibacterial

rinse

Recommended program for

routine washes, with dried-on

food (e.g. EN 50242) X 7-14 1,00-1,65 80-165 Full

Pre

PrePre-

--W

WWash

ash

ashash cold

cold

coldcold Delay Crockery to be washed later. — 4.0 140.03 NO

Rapi

RapiRapid

dd 45°C

45°C

45°C45°C Delay Lightly soiled crockery, with no

dried-on food. X 11.0 300.80 NO

44 Eco

Eco

EcoEco 2)

2)2) 50°C

50°C

50°C50°C

Delay

Antibacterial

rinse

Normally soiled crockery.

Energy-saving program. X 12.0 1651.15 Full

Intensive

IntensiveIntensive 65°C

65°C

65°C65°C Delay

Antibacterial

rinse

Recommended program for

heavily soiled crockery, especially

suitable for pans and saucepans.

X 14.0 1451.60 Full

5019 396 03742

5019 396 037425019 396 03742

BEFORE USING THE APPLIANCE FOR THE

BEFORE USING THE APPLIANCE FOR THE BEFORE USING THE APPLIANCE FOR THE FIRST TIME CAREFULL

FIRST TIME CAREFULL

FIRST TIME CAREFULLFIRST TIME CAREFULLY READ THIS

Y READ THIS

Y READ THIS Y READ THIS

QUICK REFERENCE GUIDE AND THE ASSEMBL

QUICK REFERENCE GUIDE AND THE ASSEMBLQUICK REFERENCE GUIDE AND THE ASSEMBL

Y INSTRUCTIONS!

Y INSTRUCTIONS!Y INSTRUCTIONS!

Options and display description

SAL

SALSALT INDICA

T INDICA

T INDICAT INDICATOR

TOR

TORTOR

When lit (at the end of the

cycle), the salt reservoir

needs to be refilled.

DELA

DELADELAYED ST

YED ST

YED STYED START

ART

ART ART

BUTTON

BUTTONBUTTON

The wash cycle can be

programmed to start

after 2, 4 or 8 hours.

Then press the Start

button. The wash

program will start after

the set time.

RINSE AID INDICA

RINSE AID INDICARINSE AID INDICATOR

TOR

TORTOR

When lit (at the end of the

cycle), the rinse aid

dispenser needs to be

refilled.

THE CONTROL P

THE CONTROL PTHE CONTROL PANEL OF THIS DISHWASHER ACTIV

ANEL OF THIS DISHWASHER ACTIV

ANEL OF THIS DISHWASHER ACTIVANEL OF THIS DISHWASHER ACTIVA

AATES PUSHING ANY

TES PUSHING ANY

TES PUSHING ANY TES PUSHING ANY

BUTTON EXC

BUTTON EXCBUTTON EXCEPT

EPT

EPT EPT CANCEL/OFF BUTTON.

CANCEL/OFF BUTTON.

CANCEL/OFF BUTTON.CANCEL/OFF BUTTON.

FOR ENERGY SA

FOR ENERGY SAFOR ENERGY SAVING THE CONTROL PANEL DEA

VING THE CONTROL PANEL DEA

VING THE CONTROL PANEL DEAVING THE CONTROL PANEL DEACTIVA

CTIVA

CTIVACTIVATES

TES

TES TES

AUTOMA

AUTOMAAUTOMATICALL

TICALL

TICALLTICALLY AFTER 30 SECONDS IF NO CYCLE HAS ST

Y AFTER 30 SECONDS IF NO CYCLE HAS ST

Y AFTER 30 SECONDS IF NO CYCLE HAS STY AFTER 30 SECONDS IF NO CYCLE HAS STARTED.

ARTED.

ARTED.ARTED.

ANTIBACTERIAL RINSE

ANTIBACTERIAL RINSEANTIBACTERIAL RINSE 3)

3)3)

This function activates an

antibacterial rinse at the end

of the wash cycle,

guaranteeing a further

reduction of bacteria. Press

the button to activate or

deactivate the function. This

function can be used with

the programs indicated in

the table of programs. The

dishwasher door must be

kept shut for the entire

duration of the program in

order to guarantee

reduction of bacteria. If the

door is opened the indicator

lamp starts flashing.

TTABLET SETT

ABLET SETT

ABLET SETTABLET SETTING

ING

INGING

This setting allows to optimize the cycle performances

according the type of detergent used.

Push the Tablet button for 3 seconds (until the indicator

lights up) if you are using the combined detergents in

tablet (rinse aid, salt and detergent in 1 dose).

If you are using powder detergent or liquid detergent,

the Tablet indicator on the control panel has to be off.

Quick reference guide

Quick reference guideQuick reference guide

Whirlpool is a registered trademark o

Whirlpool is a registered trademark oWhirlpool is a registered trademark of Whirlpool USA

f Whirlpool USA

f Whirlpool USAf Whirlpool USA

GB -2-

-2-

-2--2-

First time use

5 7 86

1- salt reservoir

2- rinse aid dispenser

3- detergent dispenser

4- racks system

5,6,7,8- available functions on the panel

9- filters

10- spray arms

1.1. Ask your water supply company what the water hardness

water hardness

water hardnesswater hardness is... 2.

2.2. ...enter this value on

your dishwasher Suggestions for detergent use

German

degrees °dH

French

degrees °fH

English

degrees °eH

Water hardness

level

3 first PROGRAM LEDs

lit on the panel

(see table of programs)

P1 P2 P3

Gel or Powder

(rinse aid and

salt) Tabl et s

0 - 5 0 - 6.30 - 9 Soft 1

go to step 1

(see “Daily

check”)

6 - 10 7 - 12.610 - 18 Medium 2

11 - 15 19 - 27 13.3 - 18.9 Average 3

16 - 21 28 - 37 19.6 - 25.9 Medium-hard 4 if water is

HARD extra salt

needs to be

added

(go to step 1,

“Daily check”)

22 - 28 38 - 50 26.6 - 35 Hard 5

29 - 35 51 - 63 35.7 - 44.1 Very hard 6

36 - 50 64 - 90 44.8 - 62.4 Extremely hard 7

WWater hardness should be set only

ater hardness should be set only

ater hardness should be set only ater hardness should be set only

before the first wash or if water

before the first wash or if water before the first wash or if water

hardness has been changed

hardness has been changedhardness has been changed

1Visual indicator

(depending

on the model).

Unscrew cap.

Fill the salt reservoir with water

before the first wash only.

(depending on the model)

The salt level indicator lamp may remain lit

at the end of several wash cycles. If the

water hardness level falls within category

(soft), no salt is required.

Salt indica

Salt indicaSalt indicator on the con

tor on the con

tor on the contor on the control panel

trol panel

trol paneltrol panel Salt indicator on the s

Salt indicator on the s

Salt indicator on the sSalt indicator on the salt reservoir cap

alt reservoir cap

alt reservoir capalt reservoir cap

The indicator lamp lights up when SALT

NEEDS TO BE ADDED. green: OK. clear: NEEDS TO

BE ADDED

Daily check

Filling the salt reservoir -

Filling the salt reservoir - Filling the salt reservoir - Dissolve limescale (not necessary if water hardness level is set to “soft”!)

- Press and hold together Pro

Pro

ProProgram

gram

gramgrams

ss and CANCEL/Off

CANCEL/Off

CANCEL/OffCANCEL/Off buttons for minimum 3 seconds.

- Programs LEDs will indicate the water hardness setting.

- Press the Progr

Progr

ProgrProgram

amams

ss button to increase setting (when the level reaches 7, the next key press will set the level back to 1.

- Wait 30 seconds (control panel switches off) or press ST

STSTART/Resume

ART/Resume

ART/ResumeART/Resume button to save setting.

Add salt

Add salt Add salt (never add detergent!)

min. 0.8 kg / max. 1 kg

Water hardness level is factory set

for medium-hard water (level 4).

Even if you use tablets which

include salt functionality, you must

still add regeneration salt since such

detergents are not effective enough

at softening hard water.

At first

At first At first time use,

time use,

time use,time use, the salt

the salt

the salt the salt

reservoir has to be filled

reservoir has to be filled reservoir has to be filled

independently from water

independently from water independently from water

hardness level

hardness level hardness level (see

description below in step 1

“Daily check”).

Screw on the cap.

Salt residual

around the cap

need to be

removed. Some

salt reservoir have

a level indicator

integrated in the

cap (see below

how to check).

Once regeneration salt is added, immedi

Once regeneration salt is added, immediOnce regeneration salt is added, immediately start a wash program

ately start a wash program

ately start a wash programately start a wash program (the “Pre-wash” program alone is not sufficient). Residual saline solution or grains of salt can

lead to deep-down corrosion, irreparably damaging the stainless steel components. The guarantee is not applicable if faults are caused by such circumstances.

How to set water hardness in order to always assure the best cleaning results

How to set water hardness in order to always assure the best cleaning resultsHow to set water hardness in order to always assure the best cleaning results

GB -3-

-3-

-3--3-

Daily check

Check the rinse aid indicator to check the level

into the dispenser.

(depending on the model)

Rinse aid indicator on the control panel

Rinse aid indicator on the control panelRinse aid indicator on the control panel Rinse aid indicator on th

Rinse aid indicator on th

Rinse aid indicator on thRinse aid indicator on the dispenser

e dispenser

e dispensere dispenser

The indicator lamp lights up when RINSE AID NEEDS

TO BE ADDED. dark: OK. clear: NEEDS TO BE ADDED

Only use rinse aids recommended for use in domestic dishwashers. Immedia

Immedia

ImmediaImmediately

tely

telytely wipe away any rinse aid spilt accidentally. This prevents the formation of excess suds which can cause a fault function of the

appliance.

If there are streaks: reduce the dosage by turning the dial to a lower setting (1-3). If crockery is not perfectly dry: increase the dosage by turning the dial to a higher setting (5-6). Plastic dishes have more difficulty

drying and a higher rinse aid setting will not improve the situation.

Detergents with rinse aid incorporated may be effective only with longer programs. In the case of shorter programs, detergent residue may be a problem (if necessary, use powder detergent). Detergents with

rinse aid incorporated tend to form excess suds.

Daily use

Adding detergent -

Adding detergent - Adding detergent - Use only detergent specifically for dishwashers in accordance with the supplier’s recommendations

Open the cover A

(press the dedicated button).

Only fill the

detergent dispenser

prior to starting a

wash program.

Shut the cover

by pressing dedicated ribs.