Whirlpool WFE2B19XAUS Bedienungsanleitung

Whirlpool Spülmaschine WFE2B19XAUS

Lies die bedienungsanleitung für Whirlpool WFE2B19XAUS (8 Seiten) kostenlos online; sie gehört zur Kategorie Spülmaschine. Dieses Handbuch wurde von 27 Personen als hilfreich bewertet und erhielt im Schnitt 5.0 Sterne aus 14 Bewertungen. Hast du eine Frage zu Whirlpool WFE2B19XAUS oder möchtest du andere Nutzer dieses Produkts befragen? Stelle eine Frage

Download PDF

Seite 1/8

DAILY REFERENCE

GUIDE

Before using the appliance carefully read Health and Safety guide.

APPLIANCE

PRODUCT DESCRIPTION

CONTROL PANEL

0000 000 00000

Service:

1. Upper rack

2. Foldable aps

3. Upper rack height adjuster

4. Upper spray arm

5. Lower rack

6. Cutlery basket

7. Lower spray arm

8. Filter Assembly

9. Salt reservoir

10. Detergent and Rinse Aid dispensers

11. Rating plate

12. Control panel

1. On-O/Reset button with indicator light

2. Program selection button with indicator light

3. Half Load button with indicator light

4. Salt rell indicator light

5. Rinse Aid rell indicator light

6. Program indicator lights

7. Delay indicator light

8. Delay button with indicator light

9. Tablet (Tab) button with indicator light

10. Start/Pause button with indicator light / Drain out

THANK YOU FOR BUYING A WHIRLPOOL PRODUCT.

In order to receive a more complete assistance,

please register your appliance on:

www.whirlpool.com.au

You can download the Safety Instructions and the

Use and Care Guide, by visiting our website

http://docs.whirlpool.eu and following

the Instructions on the back of this booklet.

1 2 43 5 6 7

ADVICE REGARDING THE FIRST TIME USE

After installation, remove the stoppers from the racks and the reta-

ining elastic elements from the upper rack.

FILLING THE SALT RESERVOIR

The use of salt prevents the formation of LIMESCALE on the dishes and

on the machine’s functional components.

• It is important that the salt reservoir be never empty.

• It is important to set the water hardness.

The salt reservoir is located in the lower part of the dishwasher (see Pro-

duct Description) and should be lled when the SALT REFILL indicator

light in the control panel is lit .

1. Remove the lower rack and unscrew the

reservoir cap (anticlockwise).

2. -Only the rst time you do this: ll the salt re

servoir with water.

3. Position the funnel (see gure) and ll the salt

reservoir right up to its edge (approximately

1 kg); it is not unusual for a little water to leak

out.

4. Remove the funnel and wipe any salt residue

away from the opening.

Make sure the cap is screwed on tightly, so that no detergent can get

into the container during the wash program (this could damage the

water softener beyond repair).

Whenever you need to add salt, we recommend carrying out the

procedure before the washing cycle is started.

SETTING THE WATER HARDNESS

To allow the water softener to work in a perfect way, it is essential that

the water hardness setting is based on the actual water hardness in

your house. This information can be obtained from your local water

supplier.

The factory setting is for avarage (3) water hardness.

•SwitchontheappliancebypressingtheON/OFF button.

•SwitchotheappliancebypressingtheON/OFF button.

•HolddownbuttonSTART/PAUSE for 5 seconds, until you hear a

beep.

•SwitchontheappliancebypressingtheON/OFFF button.

•Theprogramindicatorlightofthecurrentsetlevelashes.

•PressbuttonP to select the desired hardness level (see WATER

HARDNESS TABLE).

•SwitchotheappliancebypressingtheON/OFFbutton.

Setting is complete!

As soon as this procedure is complete, run a program without loading.

Only use salt that has been specically designed for dishwashers.

After the salt has been poured into the machine, the SALT REFILL indi-

cator light switches o.

If the salt container is not lled, the water softener and the

heating element may be damaged as a result.

FIRST TIME USE

SALT,RINSEAIDANDDETERGENT

FILLING THE RINSE AID DISPENSER

RinseaidmakesdishDRYINGeasier.TherinseaiddispenserA should

be lled when the RINSE AID REFILL indicator light in the control

panel is lit.

1. Open the dispenser by pressing and pulling up the tab on the lidB .

2. Pour in the rinse aid (max.110 ml), making sure it does not overow

from the dispenser. If this happens, clean the spill immediately with a

dry cloth.

3. Press the lid down until you hear a click to close it.

NEVER pour the rinse aid directly into the appliance tub.

ADJUSTING THE DOSAGE OF RINSE AID

If you are not completely satised with the drying results, you can ad-

just the quantity of rinse aid used.

• SwitchthedishwasheronusingtheON/OFF button.

• SwitchitousingtheON/OFF button.

• PressbuttonSTART/PAUSE three times - a beep will be heard.

• SwitchitonusingtheON/OFF button.

•Theprogramindicatorlightofthecurrentsetlevelashes.

• PressbuttonP to select the level of rinse aid quantity to be

supplied.

• SwitchitousingtheON/OFF button

Setting is complete!

If the rinse aid level is set to ZERO (ECO), no rinse aid will be supplied. The

LOWRINSEAIDindicatorlightwillnotbelitifyourunoutofrinseaid.

A maximum of 4 levels can be set according to the dishwasher model. The

factory setting is for a medium level.

• If you see bluish streaks on the dishes, set a low number (1-2).

• If there are drops of water or limescale marks on the dishes, set a

mid-range number (3-4).

FILLING THE DETERGENT DISPENSER

To open the detergent dispenser

use the opening device A. Introduce

the detergent into the dry dispenser

B only. Place the amount of

detergent for pre-washing directly

inside the tub.

1. When measuring out the detergent re-

fer to the mentioned earlier information

to add the proper quantity. Inside the

dispenser B there are indications to help

the detergent dosing.

2. Remove detergent residues from the edges of the dispenser and

close the cover until it clicks.

3. Close the lid of the detergent dispenser by pulling it up until the

closing device is secured in place.

The detergent dispenser automatically opens up at the right time

according to the program.

If all-in-one detergents are used, we recommend using the TABLET

button, because it adjusts the program so that the best washing and

drying results are always achieved.

Water Hardness Table

Level °dH

German degrees

°fH

French degrees

1 Soft 0 - 6 0 - 10

2 Medium 7 - 11 11 - 20

3 Average 12 - 17 21 - 30

4 Hard 17 - 34 31 - 60

5 Very hard 35 - 50 61 - 90

Program

Drying

Available

options *)

Detergent

container Duration

of wash

program

(h:min)**)

Water con-

sumption

(litres/cycle)

Energy con-

sumption

(kWh/cycle)

Tub B

1. Eco 50° - 3:10 11 1,04

2. Intensive 65° - 2:30 16,5 1,65

3. Normal 55° 2:37 12,5 0,89

4. Express 30’ 50° - - 0:30 8,5 0,50

5. Soak - - - - 0:10 4 0,01

Not all options can be used simultaneously.

**) The duration of the program shown on the display or in the booklet is an estimate calculated on standard conditions. The actual time may vary

depending on many factors such as temperature and pressure of the incoming water, room temperature, amount of detergent, quantity and type of load,

load balancing, additional selected options and sensor calibration. The sensor calibration can increase program duration up to 20 min.

Standby consumption: Left-on mode consumption: 5 W - O mode consumption: 0.5 W

The Normal 55° wash cycle adheres to the regulation standard . Although it has a longer duration than other wash cycles it uses less energy AS/NZS 2007

and is less harmful to the environment.