Whirlpool WH6IC16B4M6T0 Bedienungsanleitung
Whirlpool
Spülmaschine
WH6IC16B4M6T0
Lies die bedienungsanleitung für Whirlpool WH6IC16B4M6T0 (44 Seiten) kostenlos online; sie gehört zur Kategorie Spülmaschine. Dieses Handbuch wurde von 6 Personen als hilfreich bewertet und erhielt im Schnitt 5.0 Sterne aus 3.5 Bewertungen. Hast du eine Frage zu Whirlpool WH6IC16B4M6T0 oder möchtest du andere Nutzer dieses Produkts befragen? Stelle eine Frage
Seite 1/44
EN
Quick Guide
1
THANK YOU FOR BUYING AWHIRLPOOL PRODUCT.
In order to receive amore complete assistance, please
register your appliance on: www.whirlpool.eu/register
SETTING MENU
1. Switch on the appliance by pressing the ON-OFF button.
2. Hold the Settings (Half Load ) button for 3 seconds, until you hear
a beep and the display shows „SEt”.
3. After one second the rst available setting (letter „ ”) will be displayed.
4. Press PREVIOUS /NEXT to scroll through the list of available settings
(see table below), then press START/Pause to view and change the
value of the currently selected setting.
5. Press PREVIOUS /NEXT to change the value, then press START/Pause
to save the new value or return to the main menu.
6. To change another setting, repeat points 4 and 5.
7. Press ON-OFF or wait 30 seconds to exit the menu.
LETTER
SETTING
VALUES
(Default - in bold)*
Cycle Counter - number of washing cycles
carried out by the dishwasher.
Eg. 25 cycles: 025;
Eg. 13.947 cycles:
13_947
(scrolling
for 3 times)
Water Hardness Level (see “SETTING THE WA-
TER HARDNESS” and “WATER HARDNESS TABLE”)
1 | 2 | 3 | 4 | 5
Rinse Aid Level
(see “ADJUSTING THE DOSAGE OF RINSE AID”)
0 | 1 | 2 | 3 | 4 | 5
NaturalDry (see “OPTIONS AND FUNCTIONS”)
“1” = On, “0” = O
1 | 0
Time on the oor (see “OPTIONS AND FUNCTIONS”)
“1” = On, “0” = O
1 | 0
Sound
“1” = On, “0” = O
1 | 0
Factory Settings - press START/Pause to re-
store to the factory default all the values of the
settings included in the settings menu.
-
*) The default value does not apply to the Cycle Counter.
FILLING THE SALT RESERVOIR
The use of salt prevents the formation of LIMESCALE on
the dishes and on the machine’s functional components.
The salt reservoir is located in the lower part of the dish-
washer (under the lower rack on the left side).
• It is mandatory that the salt reservoir never be empty.
• It is important to set the water hardness.
• Salt must be lled when the SALT REFILL indicator light on the control
panel is lit.
1. Remove the lower rack and unscrew the reservoir cap (anticlockwise).
2. Position the funnel (see gure) and ll the salt reservoir right up to its
edge (approximately 0,5 kg); it is not unusual for alittle water to leak out.
3. Only the rst time you do this: ll the salt reservoir with water.
4. Remove the funnel and wipe any salt residue away from the opening.
Make sure the cap is screwed on tightly so that no detergent can get into
the container during the wash program (this could damage the water sof-
tener beyond repair).
Run aprogram every time as soon as you completed relling the salt
reservoir to avoid corrosion.
WATER SOFTENING SYSTEM
Water softener automatically reduces water hardness, consequently pre-
venting scale buildup on the heater, contributing also to better cleaning ef-
ciency. This system regenerates itself with salt, therefore it is required
to rell the salt container when empty.
The frequency of regeneration depends on the water hardness level setting
- regeneration takes place once per 4-6 Eco cycles with the water hardness
level set to 3. The regeneration process occurs at the beginning of the cycle
with additional fresh water.
• Single regeneration consumes ~3 L of water;
• Takes up to 5 additional minutes for the cycle;
• Consumes below 0.005kWh of energy.
A
B
FILLING THE RINSE AID DISPENSER
Rinse aid makes dish DRYING easier. The rinse aid dis-
penser Ashould be lled when the RINSE AID REFILL
indicator light in the control panel is lit.
1. Open the dispenser B by pressing and pulling up
the tab on the lid.
2. Pour in the rinse aid (max. 110 ml), making sure it
does not overow from the dispenser. If this hap-
pens, clean the spill immediately with adry cloth.
3. Press the lid down until you hear aclick to close it.
NEVER pour the rinse aid directly into the appli-
ance tub.
D
C
FILLING THE DETERGENT DISPENSER
To open the detergent dispenser use the opening
device C. Introduce the detergent into the dry dis-
penser D only. Place the amount of detergent for
pre-washing directly inside the tub.
1. When measuring out the detergent refer to the
mentioned earlier information to add the proper
quantity. Inside the dispenser D, there are indica-
tions to help the detergent dosing.
2. Remove detergent residues from the edges of the dispenser and close
the cover until it clicks.
3. Close the lid of the detergent dispenser by pulling it up until the closing
device is secured in place.
The detergent dispenser automatically opens up at the right time accord-
ing to the program.
Usage of detergent not designed for dishwashers may cause malfunc-
tion or damage to the appliance.
CONTROL PANEL
PLEASE SCAN THE QR CODE
ON YOUR APPLIANCE IN
ORDER TO HAVE MORE
DETAILED INFORMATION
FIRST TIME USE
More information in the Daily Reference Guide on website.
Before using the appliance carefully read Safety and Installation Instructions.
After installation, please remember to remove all transport protection parts from
the dishwasher.
1. ON-OFF/Reset button with indicator light
2. PREVIOUS program button
3. NEXT program button
4. FAVOURITE program button
with indicator light
5. Salt reservoir empty indicator light
6. Rinse Aid reservoir empty indicator light
7. DESCALE indicator light
8. Closed Water Tap indicator light
9. Display
10. Program number and remaining time indicator
11. Power Clean® option button with indicator light
12. Half Load option button with indicator light/ Settings - 3 sec. press
13. Extra Dry option button with indicator light
14. Delay option button with indicator light
15. START/Pause button with indicator light
W11553946 panel 2023-01-17
W11572189 button R 2021-10-01
W11572083 button L 2022-02-15
W11569647 display 2023-02-17
1 2 3 4 5 6 7 8 9 10
11 12 13
14
15
P
3 sec.
21
65°
3 4 5 6 7 8 9 10
50 °
Eco
65°
A
55°
A
50°
A
45°
65°
SELF CLEAN
DISPLAY ON THE FLOOR
1
3
2
1. Delay Time on the oor - indicator of the time
left to the start of the cycle, when the Delay
option is set
2. Salt reservoir empty - indicator light on the
oor
3. Remaining Time on the oor - indicator of the
time left to the end of the cycle
EN
2
Quick Guide
CYCLE COUNTER - This feature shows the number of cycles the
dishwasher has performed.
For the number of cycles from 0-999, a xed number will be displayed.
Example for 25 cycles.
When the cycle number is higher than 1000, the number will scroll in
the display. The “_” represents the “
.
”, as for instance: 1.000 = 1_000,
13.947= 13_947 (the number will scroll for 3 times).
Example for
13.947 cycles:
After the cycle visualization, the display will return to visualize
„ ”
.
NOTE: The dishwasher may have already performed about 30 cycles.
This is due to the extended quality process carried out during
production. It guarantees higher product quality.
ECO program data is measured under laboratory conditions according to European Standard EN 60436:2020.
Note for Test Laboratories: For information on comparative EN testing conditions, please send an email to the following address: dw_test_support@europeanappliances.com
Pre-treatment of the dishes is not needed before any of the programs.
*) Not all options can be used simultaneously.
**) Values given for programs other than the program Eco are indicative only. The actual time may vary depending on many factors such as temperature and pressure of the incoming
water, room temperature, amount of detergent, quantity and type of load, load balancing, additional selected options and sensor calibration. The sensor calibration can increase
program duration by up to 20 min.
POWER CLEAN® - Thanks to the additional power jets this option
provides a more intensive and powerful wash in the lower rack, in the
specific area. This option is recommended for washing pots and casseroles
(Please refer to the Power Clean® loading section).
EXTRA DRY - The higher temperature during the final rinse and the
extended drying phase allow improved drying. The EXTRA DRY option
results in the lengthening of the wash cycle.
DELAY - The start of the program may be delayed for a period of time
between 0:30 and 24 hours.
The DELAY function cannot be set once a program has been started.
WATER TAP CLOSED – Alarm - Flashes when there is no inlet water or
water tap is closed.
NaturalDry - It is aconvection drying system which automatically opens
the door during/after drying phase to ensure exceptional drying perfor-
mance every day. Door opens at the temperature that is safe to your kitch-
en furniture. As additional steam protection, special designed protection
foil is added together with the dishwasher.
SENSING - When the sensor is detecting the soil level an animation
appears in the display (around 20 min.) and the cycle duration is
updated. SENSING is for the level of soiling on the dishes and is
present for all cycles (excepting Eco) adjusting the program accordingly.
HALF LOAD - If there are not many dishes to be washed, HALF LOAD is
used to save water, electricity or time, depending on the selected
program. Remember to halve the amount of detergent.
OPTIONS can be selected/ deselected, after choosing the program, directly by pressing the corresponding button (if available - the indicator
lights up) (see CONTROL PANEL). If an option is not compatible with the selected program (see PROGRAMS TABLE), the corresponding LED ashes rap-
idly 3 times and beeps will sound. The option will not be enabled. An option can change time or water or energy consumption for the program.
DESCALE – Alarm - Limescale accumulation was detected on the
internal components of the appliance. Check if the Water Hardness
Setting is at the correct value and salt is present in the salt container (see
FIRST TIME USE), then use a descaling product (WPro brand is recommended)
with Self-Clean program. After a successful descaling, the icon will stop
being displayed.
If the actions above are not performed, product performance will deteriorate.
DESCALE warning will start blinking and «dES» alarm will appear on the
display. If still no action is taken, the appliance will only allow a certain
number of cycles to be started (indicated during «dES» alarm display) and
then will be BLOCKED to prevent component damage, with only the Self-
Clean program available. Performing a full descaling will unblock the
product. In the case of extremely high amounts of limescale, descaling may
have to be performed twice to be ecient.
PROGRAMS TABLE
OPTIONS AND FUNCTIONS
Please scan the QR code on your product in order to have more detailed information.
Program Programs description
Drying
phase
NaturalDry
Available options
*)
Duration
of wash
program
(h:min)
**)
Water
consumption
(litres/cycle)
Energy
consumption
(kWh/cycle)
P1
Eco 50°- Program is suitable to clean normally soiled tableware, that
for this use, it is the most ecient program in terms of its combined
energy and water consumption, and that it is used to assess compli-
ance with the EU Ecodesign legislation.
3:30 9.9 0.77
P2
Auto Intensive 65° - Automatic program for
heavily soiled dishes and pans.
Senses the level of soil-
ing on the dishes and
adjusts the program
accordingly. When the
sensor is detecting the
soil level an animation
appears in the display
and the cycle duration
is updated.
2:25-3:10 17.0-25.0 1.30-1.70
P3
Auto Mixed 55° - Automatic program for nor-
mally soiled dishes with dried food residues.
1:20-3:20 7.5-20.5 0.75-1.20
P4
Auto Fast 50° - Automatic program for nor-
mally and lightly soiled dishes. The everyday
cycle that ensures optimal cleaning and dry-
ing performance in a shorter time.
1:00-1:50 8.0-16.0 0.70-1.10
P5
Rapid 45° - Program is recommended for limited amount of lightly-soiled
dishes with no dried food residues. Does not include the drying phase.
-
0:30-0:40 10.5-15.0 0.55-0.65
P6
Crystals 45° - Program for delicate items, which are more sensitive to
high temperatures, for example, glasses and cups.
1:40-1:50 12.5-17.0 0.95-1.20
P7
Silent 55° - Suitable for night-time operation of the appliance. Ensures
optimal cleaning and drying performance with the lowest noise emission.
3:50-4:10 10.5-14.5 0.80-1.15
P8
Sanitizing 65° - Normally or heavily soiled crockery, with additional anti-
bacterial wash. Can be used to perform maintenance of the dishwasher.
-
1:55-2:10 12.0-19.0 1.40-1.80
P9
Prewash - Used to refresh crockery planned to be washed later. Node-
tergent is to be used with this program.
-
0:12 4.5 0.10
P10
Self Clean 65° -
Program to be used to perform maintenance of the
dishwasher and water management system, to be carried out only
when the dishwasher is EMPTY using specic detergents designed for
dishwasher maintenance.
-
-
1:15 12.7 1.10
FAVOURITE PROGRAM The FAVOURITE program may be saved and
will be easily accessible. Find the program using PREVIOUS/NEXT, and
then press the FAVOURITE program button for 3 seconds.
TIME ON THE FLOOR - A LED light projected on the oor indicates the
time left to the end of the cycle. The light goes o every time the door
is opened. The light goes o at the end of a cycle.This feature is active
by default, but it is possible to deactivate it in the “SETTINGS MENU”.
Produktspezifikationen
| Marke: | Whirlpool |
| Kategorie: | Spülmaschine |
| Modell: | WH6IC16B4M6T0 |
Brauchst du Hilfe?
Wenn Sie Hilfe mit Whirlpool WH6IC16B4M6T0 benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten
Bedienungsanleitung Spülmaschine Whirlpool
17 Juni 2025
17 Juni 2025
17 Juni 2025
17 Juni 2025
16 Juni 2025
16 Juni 2025
16 Juni 2025
16 Juni 2025
16 Juni 2025
16 Juni 2025
Bedienungsanleitung Spülmaschine
- Inventum
- Edesa
- Eurolux
- Hestan
- Samsung
- Guzzanti
- Vestel
- Kenwood
- Bar Maid
- JennAir
- Amica
- Luxor
- Noble
- Holland Electro
- Constructa
Neueste Bedienungsanleitung für -Kategorien-
17 Juni 2025
17 Juni 2025
17 Juni 2025
17 Juni 2025
17 Juni 2025
17 Juni 2025
17 Juni 2025
17 Juni 2025
17 Juni 2025
17 Juni 2025