Xantech Hidden Link 29185D Bedienungsanleitung
Lies die bedienungsanleitung für Xantech Hidden Link 29185D (4 Seiten) kostenlos online; sie gehört zur Kategorie Empfänger. Dieses Handbuch wurde von 60 Personen als hilfreich bewertet und erhielt im Schnitt 4.2 Sterne aus 30.5 Bewertungen. Hast du eine Frage zu Xantech Hidden Link 29185D oder möchtest du andere Nutzer dieses Produkts befragen? Stelle eine Frage
Seite 1/4
MODEL
29185D
Hidden Link™ Shelf Top
CFL/LCD Proof IR Receiver
INSTALLATION INSTRUCTIONS
DESCRIPTION
The Hidden Link IR Receiver is a small shelf-top infrared repeater assembly.
It includes an IR receiver and a CB12 Connecting Block. The Hidden Link IR
Receiver is equipped with a 7-foot cable and a 3.5mm stereo mini plug,
which is plugged directly into the “IR RCVR” jack on the CB12. It can also be
plugged into the “AUX” or “IR RCVR” jack of other Xantech connecting
blocks, such as the models 789-44, CB60, and 791-44. The Hidden Link IR
Receiver is primarily intended for use in installations where the connecting
block is within reach of its 7-foot cable – as when installing the Hidden Link
IR Receiver in a cabinet where the controlled equipment is behind closed
doors.
FEATURES
• Very small package, only 2.00”L x 3.15”W x 0.70”H.
• System testing red-talk-back LED.
• Includes CB12 Connecting Block for easy system installation.
SPECIFICATIONS
• Infrared carrier input frequency bandwidth: 30 - 60kHz.
• Reception range: Up to 50 feet, depending on conditions.
• Nominal reception angle: 55 degrees off axis.
• Cable requirements: See “INSTALLATION” below.
• Max. transmission length: 1 mile using 18 gauge wire.
• Maximum current output: 100mA
• Drives IR emitters through Xantech Connecting Blocks, Controllers, etc.
• Dimensions: 2.00”x3.15”x0.70” (51mm x 80mm x 18mm)
• Power requirements: +12VDC, 20mA.
INSTALLATION
QUICK-START
A typical system will use an IR receiver, several emitters, and a power supply
all connected to a connecting block.
1. Connect the IR receiver to the “IR RCVR” port on the connecting
block. The ‘red’ connector is installed to the ‘red’ plug.
Note: In some extended distances, additional 3-conductor may be required and can
be connected to the terminals on the connecting block.
2. Connect the Emitters to the connecting block. The ‘yellow’ connector
is installed to the ‘yellow’ plug.
3. Connect the power supply to the connecting block.
4. Installation complete
LOCAL SYSTEM APPLICATION
In this system a 286D Dual Blink-IR Designer Emitter is shown connected to
the “OUT” jack. A single emitter could also be used, such as the model 282D
or 283D. If expansion beyond two emitters is required, use a Xantech 789-
44, CB60, or 791-44 Connecting Block in place of the CB12. Do not use the
CB12 in this case.
Produktspezifikationen
| Marke: | Xantech |
| Kategorie: | Empfänger |
| Modell: | Hidden Link 29185D |
Brauchst du Hilfe?
Wenn Sie Hilfe mit Xantech Hidden Link 29185D benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten
Bedienungsanleitung Empfänger Xantech
24 Juni 2025
29 August 2024
26 August 2024
26 August 2024
21 Juli 2024
21 Juli 2024
20 August 2023
20 August 2023
Bedienungsanleitung Empfänger
- Rexing
- WOWiViD
- FSR
- Cambridge
- Naxa
- Induction Dynamics
- PureLink
- Inovonics
- ButtKicker
- DIO
- IFM
- NUX
- Audiotec Fischer
- Bowers And Wilkins
- Devialet
Neueste Bedienungsanleitung für -Kategorien-
21 Januar 2026
20 Januar 2026
20 Januar 2026
20 Januar 2026
18 Januar 2026
17 Januar 2026
16 Januar 2026
16 Januar 2026
16 Januar 2026
16 Januar 2026