XU1 XOS-402U Bedienungsanleitung

Lies die bedienungsanleitung für XU1 XOS-402U (2 Seiten) kostenlos online; sie gehört zur Kategorie Schleifmaschine. Dieses Handbuch wurde von 12 Personen als hilfreich bewertet und erhielt im Schnitt 5.0 Sterne aus 6.5 Bewertungen. Hast du eine Frage zu XU1 XOS-402U oder möchtest du andere Nutzer dieses Produkts befragen? Stelle eine Frage

SAFETY

INSTRUCTIONS

ALWAYS WEAR EYE, FACE

AND EAR PROTECTION

XOS-402U 0217

GENERAL POWER TOOL

SAFETY WARNINGS

ADDITIONAL SAFETY

INSTRUCTIONS FOR

SANDERS

WARNING! Read all safety

warnings and all instructions. Failure

to follow the warnings and instructions may

result in electric shock, re and/or serious

injury.

Save all warnings and instructions

for future reference. The term “power

tool” in all of the warnings refers to your

mains-operated (corded) power tool or battery-

operated (cordless) power tool.

1) Work area safety

a) Keep work area clean and well lit.

Cluttered and dark areas invite accidents.

b) Do not operate power tools in

explosive atmospheres, such as in the

presence of ammable liquids, gases or

dust.

Power tools create sparks which may ignite the dust

or fumes.

c) Keep children and bystanders away

while operating a power tool. Distractions can

cause you to lose control.

2) Electrical safety

a) Power tool plugs must match the

outlet. Never modify the plug in any

way. Do not use any adapter plugs with

earthed (grounded) power tools. Unmodied

plugs and matching outlets will reduce risk of electric

shock.

b) Avoid body contact with earthed

or grounded surfaces such as pipes,

radiators, ranges and refrigerators. There

is an increased risk of electric shock if your body is

earthed or grounded.

c) Do not expose power tools to rain or

wet conditions. Water entering a power tool will

increase the risk of electric shock.

d) Do not abuse the cord. Never use the

cord for carrying, pulling or unplugging

the power tool. Keep cord away from

heat, oil, sharp edges or moving parts.

Damaged or entangled cords increase the risk of

electric shock.

e) When operating a power tool outdoors,

use an extension cord suitable for

outdoor use. Use of a cord suitable for outdoor

use reduces the risk of electric shock.

f) If operating a power tool in a damp

location is unavoidable, use a residual

current device (RCD) protected supply.

Use of an RCD reduces the risk of electric shock.

3) Personal safety

a) Stay alert, watch what you are doing

and use common sense when operating a

power tool. Do not use a power tool while

drugs, alcohol or medication. A moment of

inattention while operating power tools may result in

serious personal injury.

b) Use personal protective equipment.

Always wear eye protection. Personal

protective equipment such as dust mask, non-skid

safety shoes, hard hat, or hearing protection used for

appropriate conditions will reduce personal injuries.

c) Prevent unintentional starting. Ensure

the switch is in the off-position before

connecting to power source and/or

battery pack, picking up or carrying the

tool. Carrying power tools with your nger on the

switch or energising power tools that have the switch

on invites accidents.

d) Remove any adjusting key or wrench

before turning the power tool on. A wrench

or a key left attached to a rotating part of the power

tool may result in personal injury.

e) Do not overreach. Keep proper footing

and balance at all times. This enables better

control of the power tool in unexpected situations.

f) Dress properly. Do not wear loose

clothing or jewellery. Keep your hair,

clothing and gloves away from moving

parts. Loose clothes, jewellery or long hair can be

caught in moving parts.

g) If devices are provided for the

connection of dust extraction and

collection facilities, ensure these are

connected and properly used. Use of dust

collection can reduce dust-related hazards.

4) Power tool use and care

a) Do not force the power tool. Use the

correct power tool for your application.

The correct power tool will do the job better and safer

at the rate for which it was designed.

b) Do not use the power tool if the switch

does not turn it on and off. Any power tool

that cannot be controlled with the switch is dangerous

and must be repaired.

c) Disconnect the plug from the power

source and/or the battery pack from

the power tool before making any

adjustments, changing accessories, or

storing power tools. Such preventive safety

measures reduce the risk of starting the power tool

accidentally.

d) Store idle power tools out of the reach

of children and do not allow persons

unfamiliar with the power tool or these

instructions to operate the power tool.

Power tools are dangerous in the hands of untrained

users.

e) Maintain power tools. Check for

misalignment or binding of moving parts,

breakage of parts and any other condition

that may affect the power tools operation.

If damaged, have the power tool repaired

before use. Many accidents are caused by poorly

maintained power tools.

f) Keep cutting tools sharp and clean.

Properly maintained cutting tools with sharp cutting

edges are less likely to bind and are easier to control.

g) Use the power tool, accessories

and tool bits etc. in accordance with

these instructions and in the manner

intended for the particular type of power

tool, taking into account the working

conditions and the work to be performed.

Use of the power tool for operations different from

those intended could result in a hazardous situation.

5) Service

a) Have your power tool serviced by

a qualied repair person using only

identical replacement parts. This will ensure

that the safety of the power tool is maintained.

Operating Instructions

XOS-402U

135W

Orbital Sander

22

XU1 Power tools

iSC GmbH, Eschenstraße 6, D-94405 Landau, Germany

Telephone: GB: 0151 294 4488 / IRL: 1850 882711

WARNING!This appliance is

not intended for use by persons

(including children) with reduced physical,

sensory or mental capabilities, or lack of

experience and knowledge, unless they

have been given supervision or instruction

concerning use of the appliance by a person

responsible for their safety.

Safety Warnings common for Sanding

Operations:

a) This power tool is intended to function

as a sander. Read all safety warnings,

instructions, illustrations and

specications provided with this power

tool. Failure to follow all instructions listed

below may result in electric shock, re

and/or serious injury.

b) Operations such as grinding, wire

brushing or cutting-off are not

recommended to be performed with

this power tool. Operations for which the

power tool was not designed may create a

hazard and cause personal injury.

c) Do not use accessories which

are not specically designed

and recommended by the tool

manufacturer. Just because the

accessory can be attached to your power

tool, it does not assure safe operation.

d) The rated speed of the accessory

must be at least equal to the maximum

speed marked on the power tool.

Accessories running faster than their rated

speed can break and y apart.

e) The outside diameter and the thickness

of your accessory must be within the

capacity rating of your power tool.

Incorrectly sized accessories cannot be

adequately guarded or controlled.

f) Threaded mounting of accessories

must match the spindle thread.

Accessories that do not match the

mounting hardware of the power tool will

run out of balance, vibrate excessively and

may cause loss of control.

g) Do not use a damaged accessory.

Before each use inspect the accessory

such as a backing pad for cracks,

tears or excess wear. If power tool

or accessory is dropped, inspect

for damage or install an undamaged

accessory. After inspecting and

installing an accessory, position

yourself and bystanders away from the

plane of the rotating accessory and

run the power tool at maximum no-

load speed for one minute. Damaged

accessories will normally break apart

during this test time.

h) Wear personal protective equipment.

Depending on application, use face

shield, safety goggles or safety

glasses. As appropriate, wear dust

mask, hearing protectors, gloves

and workshop apron capable of

stopping small abrasive or work

piece fragments. The eye protection

must be capable of stopping ying

debris generated by various operations

. The dust mask or respirator must be

Description of symbols

Read instruction manual

Do not expose to rain

Wear dust mask

Wear ear protection

Wear eye protection

Double insulated

Volts

Hertz

Watts

Warning

Alternating current

Revolutions, reciprocations or strokes per

minute

No load speed

/min

n

o

V

Hz

W

capable of ltrating particles generated

by your operation. Prolonged exposure

to high intensity noise may cause

hearing loss.

i) Keep bystanders a safe distance away

from work area. Anyone entering

the work area must wear personal

protective equipment. Fragments of work

piece or of a broken accessory may y

away and cause injury beyond immediate

area of operation.

k) Position the cord clear of the spinning

accessory. If you lose control, the cord

may be cut or snagged and your hand

or arm may be pulled into the spinning

accessory.

l) Never lay the power tool down until

the accessory has come to a complete

stop. The spinning accessory may grab the

surface and pull the power tool out of your

control.

m) Do not run the power tool while

carrying it at your side. Accidental contact

with the spinning accessory could snag

your clothing, pulling the accessory into

your body.

n) Regularly clean the power tool’s air

vents. The motor’s fan will draw the

dust inside the housing and excessive

accumulation of powdered metal may

cause electrical hazards.

o) Do not operate the power tool near

ammable materials. Sparks could ignite

these materials.

p) Do not use accessories that require

liquid coolants. Using water or other liquid

coolants may result in electrocution or

shock.

Kickback and Related Warnings

Kickback is a sudden reaction to a pinched

or snagged rotating wheel, backing pad,

brush or any other accessory. Pinching

or snagging causes rapid stalling of the

rotating accessory which in turn causes the

uncontrolled power tool to be forced in the

direction opposite of the accessory’s rotation

at the point of the binding.

For example, if an abrasive wheel is

snagged or pinched by the work piece, the

edge of the wheel that is entering into the

pinch point can dig into the surface of the

material causing the wheel to climb out or

kick out. The wheel may either jump toward

or away from the operator, depending on

direction of the wheel’s movement at the

point of pinching. Abrasive wheels may also

break under these conditions.

Kickback is the result of power tool misuse

and/or incorrect operating procedures or

conditions and can be avoided by taking

proper precautions as given below.

a) Maintain a rm grip on the power tool

and position your body and arm to allow

you to resist kickback forces. Always

use auxiliary handle, if provided, for

maximum control over kickback or

torque reaction during start-up. The

operator can control torque reactions or

kickback forces, if proper precautions are

taken.

b) Never place your hand near the

rotating accessory. Accessory may

kickback over your hand.

c) Do not position your body in the area

where power tool will move if kickback

occurs. Kickback will propel the tool in

direction opposite to the wheel’s movement

at the point of snagging.

d) Use special care when working

corners, sharp edges etc. Avoid

bouncing and snagging the accessory.

Corners, sharp edges or bouncing have a

tendency to snag the rotating accessory

and cause loss of control or kickback.

e) Do not attach a saw chain woodcarving

blade or toothed saw blade. Such blades

create frequent kickback and loss of

control.

Safety Warnings Specic for Sanding

Operations

a) Do not use excessively oversized

sanding disc paper. Follow

manufacturers recommendations, when

selecting sanding paper. Larger sanding

paper extending beyond the sanding pad

presents a laceration hazard and may

cause snagging, tearing of the disc or

kickback.

Unplug the sander before changing

accessories.Accidental start-ups may occur

if the sander is plugged in while changing an

accessory.

Disposing of dust. Be extremely careful of

dust disposal, materials in ne particle form

may be explosive. Do not throw sanding dust

on an open re. Spontaneous combustion,

may in time, result from a mixture of oil or

water with dust particles.

WARNING! Some dust created by

power sanding, sawing, grinding,

drilling and other construction activities

contain chemicals known to cause cancer,

birth defects or other reproductive harm.

Some examples of these chemicals are:

• Lead from lead-based paints;

• Crystalline silica from bricks, cement and

other masonry products, and;

• Arsenic and chromium from chemically-

treated timber.

The risk from such exposures vary

depending on how often you do this type

of work. To reduce your exposure to these

chemicals; work in a well ventilated area,

and work with approved safety equipment,

such as those dust masks that are

specically designed to lter out microscopic

particles.

Produktspezifikationen