Behringer Oscillator Module 1004 Bedienungsanleitung
Seiten 2 Engels Synthesizer
Lies die Bedienungsanleitung für Behringer Oscillator Module 1004 kostenlos online oder lade das PDF herunter. 52 Personen fanden diese Anleitung hilfreich. Frage zu diesem Modell? Stelle eine Frage
Quick Start Guide
OSCILLATOR MODULE 1004
Legendary 2500 Series Dual Core VCO
Module for Eurorack
Controls
(1) COARSE FREQUENCY – Sets the frequency from 0.03 to
32 Hz in the low (LFO) range, or from 15.5 Hz to 16 kHz in
the high (audio) range, depending on the Fine frequency
knob setting.
(2) FINE FREQUENCY – Adjusts the frequency by a factor of
±1 octave, potentially halving or doubling the frequency
at either extreme.
(3) ENABLE switch – Turns the oscillator on and o.
(4) RANGE switch – Determines whether the oscillator
operates in the low (subsonic/LFO) band or the high
(audio) band.
(5) WAVEFORM switches – Engage up to 5 waveforms by
moving the relevant toggle switch to the left, or engage
the inverse waveform by moving the switch to the right.
The center position turns the waveform o. Engaging
multiple switches simultaneously produces the average of
all active waveforms.
(6) PW knob – Manually control the pulse width for the
pulse waveform.
(7) FM 2 knob – Attenuates the signal connected to the FM
2 input.
(8) PWM knob – Adjusts the modulation depth of the PMW
control input.
(9) FM 1 knob – Attenuates the signal connected to the FM
1 input.
(10) KYBD – Connect a keyboard or other external frequency
control via 3.5 mm TS cable.
(11) FM 1/2 – Connect external voltages to modulate
the frequency.
(12) PWM – Connect an external voltage to modulate the
pulse width.
(13) OUT – Send the oscillator signal to other modules via
3.5 mm TS cable.
Power Connection
The unit comes with the required power cable for connecting
to a standard Eurorack power supply system. Follow these
steps to connect power to the module. It is easier to make
these connections before the module has been mounted into
a rack case.
1. Turn the power supply or rack case power o and
disconnect the power cable.
2. Insert the 16-pin connector on the power cable into the
socket on the power supply or rack case. The connector
a tab that will align with the gap in the socket, so it cann
be inserted incorrectly. If the power supply does not hav
a keyed socket, be sure to orient pin 1 (-12 V) with the re
stripe on the cable.
3. Insert the 10-pin connector into the socket on the back
the module. The connector has a tab that will align with
socket for correct orientation.
4. After both ends of the power cable have been securely
attached, you may mount the module in a case and turn
the power supply.
(1)
(2)
(3)
(6)
(7)
(8)
(5)
(4)
(9)
()( )()( )1011 1213
V 1.0
Produktspezifikationen
| Marke: | Behringer |
| Kategorie: | Synthesizer |
| Modell: | Oscillator Module 1004 |
Brauchst du Hilfe?
Wenn Sie Hilfe mit Behringer Oscillator Module 1004 benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten
Bedienungsanleitung Synthesizer Behringer
Behringer Model D Bedienungsanleitung Behringer System 55 994 Multiples Bedienungsanleitung Behringer System 100 172 Phase Shifter/Delay/LFO Bedienungsanleitung Behringer System 35 Bedienungsanleitung Behringer System 15 Bedienungsanleitung Behringer Modamp Module 1005 Bedienungsanleitung Behringer CP1A Bedienungsanleitung Behringer Eurorack Ears Bedienungsanleitung
Alle Behringer Synthesizer Bedienungsanleitungen
Beliebt in Synthesizer
Behringer CAT Bedienungsanleitung Behringer Poly D Bedienungsanleitung Behringer WAVE Bedienungsanleitung
Bedienungsanleitung Synthesizer
Neueste Bedienungsanleitungen für Synthesizer
Korg Opsix module Bedienungsanleitung Korg King NEO Bedienungsanleitung Roland JUPITER-8 Bedienungsanleitung Roland PROMARS Bedienungsanleitung Roland D-05 Bedienungsanleitung Roland XPS-10X Bedienungsanleitung Moog MiniVoyager RME Bedienungsanleitung Moog MiniModel D Bedienungsanleitung Moog MiniVoyager Bedienungsanleitung Moog Little Phatty Stage II Bedienungsanleitung