Behringer System 100 172 Phase Shifter/Delay/LFO Bedienungsanleitung
Seiten 2 Engels Synthesizer
Lies die Bedienungsanleitung für Behringer System 100 172 Phase Shifter/Delay/LFO kostenlos online oder lade das PDF herunter. 43 Personen fanden diese Anleitung hilfreich. Frage zu diesem Modell? Stelle eine Frage
Quick Start Guide
SYSTEM 100
172 PHASE SHIFTER/
DELAY/LFO
Legendary Analog Phase Shifter/
Delay/LFO Module for Eurorack
Controls
(1) CV IN – Accepts voltage from an external source to
control or modulate the phase shifter frequency or audio
delay time. If no jack is inserted the LFO can be used to
modulate the eect.
(2) MOD INTENSITY – Controls how much the eect is
modulated by the LFO or external CV input.
(3) EFFECT ON/OFF – Engages or disengages the
eect section.
(4) SHIFT FREQ – Adjusts the frequency of the phase shifter.
(5) SIG IN – Accepts an incoming signal via 3.5 mm TS cable.
(6) SIG OUT – Sends the signal from the eect section.
(7) RESONANCE – Adjusts the amount of signal that is fed
back through the eect.
(8) DELAY TIME – Adjusts the time of the delay eect.
(9) FREQUENCY – Controls the LFO output frequency.
(10) LFO OUT – Sends the LFO signal as a triangle and inverted
triangle wave.
(11) THRESHOLD – Controls the input voltage level required to
trigger the gate.
(12) GATE IN – Accepts an incoming gate signal via 3.5 mm
TS cable.
(13) GATE OUT – Send the gate delay signal via 3.5 mm
TS cable.
(14) GATE TIME – Controls the gate length.
Power Connection
The module comes with the required power cable for connecting
to a standard Eurorack power supply system. Follow these
steps to connect power to the module. It is easier to make
these connections before the module has been mounted into
a rack case.
1. Turn the power supply or rack case power o and
disconnect the power cable.
2. Insert the 16-pin connector on the power cable into the
socket on the power supply or rack case. The connector has
a tab that will align with the gap in the socket, so it cannot
be inserted incorrectly. If the power supply does not have
a keyed socket, be sure to orient pin 1 (-12 V) with the red
stripe on the cable.
3. Insert the 10-pin connector into the socket on the back of
the module. The connector has a tab that will align with the
socket for correct orientation.
4. After both ends of the power cable have been securely
attached, you may mount the module in a case and turn on
the power supply.
(1)
(2)
(8)
(6)(5)(4)
(11) (14)
(7)
(13)
(9)
(10)
(3)
(12)
Produktspezifikationen
| Marke: | Behringer |
| Kategorie: | Synthesizer |
| Modell: | System 100 172 Phase Shifter/Delay/LFO |
Brauchst du Hilfe?
Wenn Sie Hilfe mit Behringer System 100 172 Phase Shifter/Delay/LFO benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten
Bedienungsanleitung Synthesizer Behringer
Behringer PRO-1 Bedienungsanleitung Behringer 2600-VCO Bedienungsanleitung Behringer Model D Bedienungsanleitung Behringer System 55 994 Multiples Bedienungsanleitung Behringer System 35 Bedienungsanleitung Behringer Oscillator Module 1004 Bedienungsanleitung Behringer System 15 Bedienungsanleitung Behringer Modamp Module 1005 Bedienungsanleitung
Alle Behringer Synthesizer Bedienungsanleitungen
Beliebt in Synthesizer
Behringer CAT Bedienungsanleitung Behringer Poly D Bedienungsanleitung Behringer WAVE Bedienungsanleitung
Bedienungsanleitung Synthesizer
Neueste Bedienungsanleitungen für Synthesizer
Korg PS-3300 Bedienungsanleitung Korg micro 2 Bedienungsanleitung Moog Messenger Bedienungsanleitung Roland JUNO-D8 Bedienungsanleitung Twisted Electrons TWISTfm FM Bedienungsanleitung Roland XV-2020 Bedienungsanleitung Yamaha PSR-F52 Bedienungsanleitung LennarDigital Sylenth 1 Bedienungsanleitung Korg i30 Bedienungsanleitung Korg N264 Bedienungsanleitung