BlendMount BMX-2130 Bedienungsanleitung
BlendMount
Nicht kategorisiert
BMX-2130
Lies die bedienungsanleitung für BlendMount BMX-2130 (2 Seiten) kostenlos online; sie gehört zur Kategorie Nicht kategorisiert. Dieses Handbuch wurde von 22 Personen als hilfreich bewertet und erhielt im Schnitt 4.9 Sterne aus 11.5 Bewertungen. Hast du eine Frage zu BlendMount BMX-2130 oder möchtest du andere Nutzer dieses Produkts befragen? Stelle eine Frage
Seite 1/2
PART# BMX-2130
Bland
fflaunf-®
ESCOR'C
PASSPORT
MAX
LEFT HAND DRIVE VEHICLE
1111111111,
1111111111!
Innovat
i
ve
Mount
i
ng
Solut
i
on
s
7
28028
34181
2
INSTALLATION INSTRUCTIONS FOR
THE
ESCORT
PASSPORT MAX RADAR
DETECTOR
Your rear view mirror has minimal clearance between the back side
of
the mirror and the mirror stem. It is
very important that tt
•s
mount is installed correctly to ensure mirror adjustability is retained.
PLEASE READ THE E INSTRUCTIONS THOROUGHLY BEFORE INSTALLING THIS MOUNT
NOTE: For illustration urposes, the mount and rear view mirror shown in these instruction may look
slightly different then YOUR mount and rear view mirror.
TRIGGER
BOTTOM OF SPRING CLIP
IS PARALLEL WITH RD
1 - The RELEASE Button on the radar detector (RD) is NOT used with this mount.
2 • The bottom
of
the spring clip must be parallel with the
top
of
the RD to slide In and out. SLIDE THE RD ONTO
THE
SPRING CLIP AS FAR AS
IT
WILL GO. Release the
trigger
to
secure the RD onto the mount. Before installing
the
mount
onto
your
rear
view
mirror, remove and install the
RD
a
few
times so you can observe
how
the spring clip functions.
To
release the tension
of
the spring clip, simply squeeze the
TRIGGER
and the back side
of
the mount together. This will lower the bottom portion
of
the spring clip allowing you
to
slide the RD on and
off
. When used properly, the spring clip avoids putting excessive
pressure on the mirror stem
when
installing and removing the RD. The top portion
of
the.mount should barely move when the two opposing forces are applied.
TOP
SECTION
MID
SECTION
BODY
ASSEMBLY
3 •
The
BODY
ASSEMBLY
must
be removed to gain access to the
CLAMP
SCREW. Remove
the
two socket head screws as shown
above.
Be
sure to remove the lock
washer
with the top screw along with
the lock washer and flat
washer
with the bottom screw. Loosen the
CLAMP
SCREW
so
there is enough clearance between the
TOP
and
MID SECTIONS
to
slide over the mirror stem.
lnnovativ Design And
Precision Manufacturing
PIVOT
POINT
TOP AND MID
SECTIONS
MUST
TOUCH
AT THE PIVOT POINT
BEFORE CLAMP SCREW
IS FULLY TIGHTENED
4 • While sitting
in
the passenger seat, place the
mount
over the mirror
stem. Tighten the
CLAMP
SCREW
until the mount starts
to
clamp onto the
mirror stem.
As
you are tightening the clamp screw, MAKE SURE
THE
TOP
AND MID SECTIONS TOUCH AT THE PIVOT POINT.
If
they
do
not
touch
at
the pivot point.
YOU
HAVE AN INCOMPATIBLE MIRROR TYPE FOR
THIS
MOUNT
. Position the mount as far forward as it will
go
and parallel to
the bottom
of
the mirror before fully tightening.
PAGE 1
OF
2
BlendMount -
US
PATENT#
D625,580 S, D656,811 S, D653,980 S
D690,
245
S, D690,
246
S, D690,
247
Sand
other patents pending
Produktspezifikationen
| Marke: | BlendMount |
| Kategorie: | Nicht kategorisiert |
| Modell: | BMX-2130 |
Brauchst du Hilfe?
Wenn Sie Hilfe mit BlendMount BMX-2130 benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten
Bedienungsanleitung Nicht kategorisiert BlendMount
13 September 2025
29 August 2024
29 August 2024
29 August 2024
29 August 2024
29 August 2024
29 August 2024
29 August 2024
29 August 2024
29 August 2024
Bedienungsanleitung Nicht kategorisiert
- Neno
- TROND
- Electro-Voice
- DreamLine
- Camec
- Masterbuilt
- Aiptek
- Porsche
- MIPRO
- TFA
- Fujifilm
- Hetman
- Tonar
- Voigtländer
- DECROSS
Neueste Bedienungsanleitung für -Kategorien-
20 Januar 2026
20 Januar 2026
20 Januar 2026
20 Januar 2026
20 Januar 2026
20 Januar 2026
20 Januar 2026
20 Januar 2026
20 Januar 2026
20 Januar 2026