Blustream MFP62 Bedienungsanleitung

Blustream Router MFP62

Lies die bedienungsanleitung für Blustream MFP62 (8 Seiten) kostenlos online; sie gehört zur Kategorie Router. Dieses Handbuch wurde von 47 Personen als hilfreich bewertet und erhielt im Schnitt 4.6 Sterne aus 24 Bewertungen. Hast du eine Frage zu Blustream MFP62 oder möchtest du andere Nutzer dieses Produkts befragen? Stelle eine Frage

Download PDF

Seite 1/8

MFP62

User Manual

RevA1 MFP62 User Manual

www.blustream.com.au www.blustream.co.uk |

MFP62 USER MANUAL

Contents

Surge protection device

recommended

This product contains sensitive

electrical components that may be

damaged by electrical spikes, surges,

electric shock, lightning strikes, etc.

Use of surge protection systems is

highly recommended in order to

protect and extend the life of your

equipment.

Thank you for purchasing

this product.

For optimum performance and safety,

please read these instructions carefully

before connecting, operating or

adjusting this product. Please keep this

manual for future reference.

Introduction 03

Features 03

Panel Descriptions 04

Microphone Input & Audio Mixing 05

EDID Control 06

Scaler Control 06

Infrared (IR) Distribution 07

Remote Control 08

RS-232 Control Port 09-10

Specification 11

Package Contents 11

Maintenance 11

Schematic 12

Installer Notes 13

www.blustream.com.au www.blustream.co.uk |

MFP62 USER MANUAL

Panel Description - Front

Panel Description - Rear

1 LCD display – Shows the status of input/output selection,

EDID etc

2 Power button – Press to power on/o the Switcher.

Illuminates blue when powered on

3 Mutes all audio output

4 Input selection - To select the input signal between HDMI 1

to 3, DP, USB-C and VGA

5 Timing selection - To select scaler output video resolution

6 Menu button – Press to enter EDID, Network and MIC setup

7 Up selection button – Press to change segment’s value

8 Enter button – Press to select current menu item.

9 IR receiver window

q L/R In button - Press to select analogue audio input to be

embedded onto all video signals

w Vol +/- button - Press to adjust the volume of the audio

output for 2ch PCM signals only

e Down selection button – Press to change segment’s value

r ESC button – Press to escape the current setup menu

1 TCP/IP (RJ45) – Connect to LAN for TCP/IP control of

Switcher and Web GUI

2 RS-232 port – For control of the Switcher from PC or third

party control processor

3 Coaxial digital audio output – Extract audio from the

selected input signal

4 L/R analogue audio outputs (RCA) – Extracted audio from

the selected input signal. Note: Input signal must be PCM

2ch audio

5 Upgrade port (Micro USB) - For firmware upgrade

6 SC/MB switch - For firmware upgrade of scaler or main

board

7 HDMI input 1 - Connect to HDMI source. Supports up to 4K

60Hz 4:4:4 video and 2ch PCM audio only

8 Status LED - Illuminates when an input or output has an

active connection to a source or display

9 HDMI input 2 to 3 - Connect to HDMI source. Supports up

to 4K 60Hz 4:4:4 video and multi channel audio

q DisplayPort™ input - Connect to DisplayPort source.

Supports up to 4K 60Hz 4:4:4 and DP1.2

w USB-C input - Connect to USB-C source. Note: this port

does not support charging via USB. Supports up to 4K

60Hz 4:4:4, DP1.2 and Alt mode

e VGA input - Connect to VGA source. Supports up

1920x1200 (including 1080p)

r L/R In - 3.5mm Analogue audio input for embedding audio

onto HDMI outputs

t HDMI outputs - Connects to HDMI display. Both outputs

display the same signal concurrently

y MIC IN - Supports balanced and unbalanced microphones

including 48V phantom power

u MIC input selection - Select between 48V phantom power,

line level and mic level input sensitivity

i IR selection - Select between 5V or 12V IR on the IR CTRL

connection. See full manual for pin out

o IR CTRL receiver input – 3.5mm stereo jack for connection

of an IR receiver or control processor for remote IR control

of the switcher

p Power port – Use included 24V/1A DC adaptor to power

the switcher

2 3 5

10 11 13

6 7 8

3 4

13 16 19

5 6

7 9 10 11 14 15 178

Produktspezifikationen

Marke:	Blustream
Kategorie:	Router
Modell:	MFP62
Breite:	344 mm
Tiefe:	168 mm
Produktfarbe:	Schwarz
Höhe:	44 mm
Betriebstemperatur:	0 - 40 °C
Netzteil Ausgangsspannung:	24 V
AC-Adapter Ausgangssstrom:	1 A
HD-Typ:	4K Ultra HD
Anzahl HDMI-Anschlüsse:	5
Temperaturbereich bei Lagerung:	-20 - 60 °C
Montageset:	Ja
RS-232 port:	1
HDCP:	Ja
Rack-Einbau:	Ja
Anzahl VGA (D-Sub) Anschlüsse:	1
HDMI-Version:	2.0
Anzahl der HDMI-Ausgänge:	2
Bandbreite:	18 Gbit/s
Anzahl DisplayPort Anschlüsse:	1
S/PDIF-Ausgang:	Ja
HDMI-In:	3
HDCP-Version:	2.2
Video Porttyp:	HDMI/VGA/DisplayPort
VGA (D-Sub)-Eingangsanschlüsse:	1
3,5 mm (1/8-inch) in:	Ja
Rack-Kapazität:	1U
RJ-45-Eingangsanschlüsse:	1
USB-Port-Typ:	USB Typ-C
Dolby-Technologie:	DTS-HD Master Audio, Dolby Atmos, Dolby TrueHD
Erweiterte Display-Identifikationsdaten (EDID):	Ja