Boyo VTL17LTJ Bedienungsanleitung
Lies die bedienungsanleitung für Boyo VTL17LTJ (10 Seiten) kostenlos online; sie gehört zur Kategorie Dashcam. Dieses Handbuch wurde von 14 Personen als hilfreich bewertet und erhielt im Schnitt 4.9 Sterne aus 7.5 Bewertungen. Hast du eine Frage zu Boyo VTL17LTJ oder möchtest du andere Nutzer dieses Produkts befragen? Stelle eine Frage
Seite 1/10
II. Specifications
SENSOR PC1058
Effective Pixel 976×592
Video output 1.0 vp, 75 Ohm-p
Vertical Sync Frequency
Scanning System 2 : 1 Interlace
Sync System Internal
AGC Auto
BLC Auto
Resolution 700 TV Lines
S/N Ratio More Than 48dB
Current Consumption No More 150mA
DC12V ± 10%
-22° ~ 176° F
-40°
~ 176° F
Power Supply
Operating Temperature
Storage Temperature
Viewing Angle
170°
Water-Proof
Minimum Illumination
IP68
0.5Lux/F1.2(0Lux with LED)
III. Installation
1) Findasuitable location to surface mount install the camera. Make sure the
camera’s view is unobstructed and be careful not to drill into any wires that might
damage the vehicle. When all connections have been made and before
mounting the camera, verify the camera is working and has good view of the
area. Then mount the camera down with the supplied two screws.
2) Connect the RED wire to the +12 volt reverse wire
5) Run video cable though vehicle, up to video monitor. (Avoid placing
video cable where it can get pinched or damaged).
6) Attach the YELLOW video rc
a to the reverse camera input of the radio or
video monitor; connect the RED wire coming from the YELLOW video rca
to the reverse trigger wire on the radio or video monitor.
NOTE: The camera comes with trajectory lines and a mirror image view active.
If you want to remove the parking lines or change the image to reverse image,
follow the steps below:
A) Disconnect power to the camera.
B)
C)
Cut the BLUE loop to remove the trajectory parking lines , isolate and tape the wires.
Cut the WHITE loop to get normal image, isolate and tape the wires.
.
D) Reconnect power to the camera.
If the trajectory parking lines are needed or the image needs to go back to
reverse, just follow the steps above and reconnect the wires.
For any technical support, contact 888-941-3060 or email [email protected]
WWW.VISIONTECHAMERICA.COM
VTL17LTJ
Concealed Mount License Plate Camera with LED Lights/
Trajectory Parking Lines
I.Bill of Materials
Camera
24ft 4mini pin ware harness(1pcs)
User manual(1pcs)
Warranty Card(1pcs)
Registration Card(1pcs)
Screw x2(KM6X24)
Screw x2(Pm3x10X7)
Screw x2(Pm2.5x8)
Conversionconnectorx1
Bracketx1
3M double stickerx1
NTSC 60HZ
3) Connect the BLACK wire to Chassis ground (a metal , non-painted surface).
4) Connect the GREEN wire to the + 12V volt reverse wire.
Control Wires
Blue Loop: cut = turns off trajectory lines
White Loop: cut = display non-mirror images
Green wire: connect to reverse backup light
positive = LED will turn on whenever backup
light is on.
** Monitor trigger ** when reverse backup light comes
on it will trigger the monitor to switch to backup camera.
Produktspezifikationen
| Marke: | Boyo |
| Kategorie: | Dashcam |
| Modell: | VTL17LTJ |
Brauchst du Hilfe?
Wenn Sie Hilfe mit Boyo VTL17LTJ benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten
Bedienungsanleitung Dashcam Boyo
14 September 2025
28 August 2024
21 August 2024
21 August 2024
21 August 2024
21 August 2024
21 August 2024
20 August 2024
20 August 2024
20 August 2024
Bedienungsanleitung Dashcam
- Sencor
- Tracer
- Thinkware
- Kapture
- Xblitz
- Iconbit
- ModeCom
- Scosche
- DOD
- VIOFO
- Skytronic
- Trebs
- Genius
- Ednet
- Rollei
Neueste Bedienungsanleitung für -Kategorien-
20 Januar 2026
19 Januar 2026
19 Januar 2026
17 Januar 2026
7 Januar 2026
31 Dezember 2026
19 Dezember 2025
5 Dezember 2025
12 November 2025
10 November 2025