Caliber PARK 500 Bedienungsanleitung
Caliber
Nicht kategorisiert
PARK 500
Lies die bedienungsanleitung für Caliber PARK 500 (11 Seiten) kostenlos online; sie gehört zur Kategorie Nicht kategorisiert. Dieses Handbuch wurde von 51 Personen als hilfreich bewertet und erhielt im Schnitt 4.2 Sterne aus 26 Bewertungen. Hast du eine Frage zu Caliber PARK 500 oder möchtest du andere Nutzer dieses Produkts befragen? Stelle eine Frage
Seite 1/11
E N G L I S H
1
PARK 500 PARKING SENSOR SYSTEM
PARK 500 consists of ultrasonic sensors, camera and digital control
box. (Besides these, a outer connected display with RCA plug is
needed).The video signal is inputted into control box via VIN (video
Input) and processed by control box, then outputted to outer
connected display with RCA plug via VOUT (Video Output). This
system detects the distance between the car and back obstruction
by ultrasonic sensors fixed at rear bumper of the car, and the display
shows the back image via the camera fixed at the rear of the car.
With the change of alarm sound, figure or simulation bars as well as
the image, the driver could judge the distance to avoid accident.
INSTALLATION TOOLS
ADVISED POSITION TO INSTAL THE SENSORS
SELECT DRILLING POSITION FOR SENSOR A AND D
A B E C D
Ø 21 mm
for sensor
Ø 25 mm
for camera
A. 4 drilled holes (A, B, C, D) and camera hole
(E) should be under the same line
B. 0.5-0.8m vertically high to the ground, 0.55m
is recommended
C.Vertical, tidy surface without metal
components is preferred.
A. Choose suitable drilling position for A and D
sensor with relevant mark
E N G L I S H
2
SELECT DRILLING POSITION FOR SENSOR AND CAMERA B,C AND E
DRILLING
SENSOR AND CAMERA INSTALLATION
B.To perform the best detecting angle, select the
position for A and D sensor with 8-13cm away
from the side, 11cm is recommended, and 20°
with the side.
A.Measure the distance between sensor A and D,
get the result “L”.
B.Mark sensor B, C and E for every 1/4 “L”
interval. (Camera E should be in the middle of
the bumper)
A.Firstly, use a small driller tip to locate.
B.Drill with the original driller. Ø21MM
DRILLER FOR SENSOR HOLES AND
Ø25MM DRILLER FOR CAMERA HOLE.
A.Insert the sensors and camera into the holes
one by one and tighten them, the sensor with
metal slice must be up and down fixed instead
of right and left.The camera must be fixed with
the triangle mark upward.
B.Hide the wires in good order according to
various cars.
E N G L I S H
4
SENSOR DETECTING
SENSOR AND CAMERA INSTALLATION DIAGRAM
The direction of sensors
DETECTING RANGE
1.5m
90° 90° 90°
Camera
Sensor
0.6 - 0.8m 0.3 - 0.4m
The best postiton for 2 sensors The best postiton for 4 sensors
Notice: Fix the camera in the
middle of bumper on the same
level with sensors.
0.5 - 0.8m
Vertical installation position to the ground.
Sloping installation position to the ground.
Top view Side view
Produktspezifikationen
| Marke: | Caliber |
| Kategorie: | Nicht kategorisiert |
| Modell: | PARK 500 |
Brauchst du Hilfe?
Wenn Sie Hilfe mit Caliber PARK 500 benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten
Bedienungsanleitung Nicht kategorisiert Caliber
25 August 2024
25 August 2024
14 August 2024
13 August 2024
12 August 2024
11 August 2024
8 August 2024
6 August 2024
28 Juli 2024
24 Juli 2024
Bedienungsanleitung Nicht kategorisiert
- KM-fit
- SPC
- Genelec
- Xvive
- Profoto
- Playmobil
- Exquisit
- Etymotic
- Coravin
- WarmlyYours
- Firefield
- Megasat
- CSFG
- Reber
- Palm
Neueste Bedienungsanleitung für -Kategorien-
7 August 2025
7 August 2025
7 August 2025
7 August 2025
7 August 2025
7 August 2025
7 August 2025
7 August 2025
7 August 2025
7 August 2025