Canarm BPT12-13H1 Bedienungsanleitung

Lies die bedienungsanleitung für Canarm BPT12-13H1 (6 Seiten) kostenlos online; sie gehört zur Kategorie Ventilator. Dieses Handbuch wurde von 11 Personen als hilfreich bewertet und erhielt im Schnitt 4.6 Sterne aus 6 Bewertungen. Hast du eine Frage zu Canarm BPT12-13H1 oder möchtest du andere Nutzer dieses Produkts befragen? Stelle eine Frage

CANARMNACANARMNA

BATHROOM

EXHAUST FANS

BPT12-13H

OPERATION INSTRUCTIONS AND PARTS MANUAL

READ AND SAVE THESE INSTRUCTIONS

GENERAL SAFETY

WARNING - TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK OR INJURY TO PERSONS, OBSERVE THE FOLLOWING:

1.This ventilation fan is approved for use over a bathtub or shower when installed in a GFCI protected circuit. Do not use unapproved

fans over a bathtub or shower that does not include a GFCI protected circuit.

2.Installation work must be carried out by a qualified person(s) in accordance with all local and safety codes including the rules for

fire-rated construction.

3.To reduce the risk of fire, always vent fans to the exterior and in compliance with local codes. Do not vent exhaust air into spaces

within walls, ceilings, attics, crawl spaces, or garages.

4.Install ductwork in a straight line with minimal bends.

5.Use 120 V, 60 Hz for the electrical supply and properly ground the unit. Follow all local safety and electrical codes.

6.Do not use this fan with any solid state control device; such as a dimmer switch. Solid-state controls may cause harmonic distortion,

which can cause a motor humming noise.

7.Use this unit only in the manner intended by the manufacturer. If you have questions, contact the manufacturer.

8.Before servicing or cleaning unit, switch power off at service panel and lock the service disconnecting means to prevent power from

being switched on accidentally. When the service disconnecting means cannot be locked, securely fasten a prominent warning device,

such as a tag, to the service panel.

9.Sufficient air is needed for proper combustion and exhausting of gases through the flue (chimney) of fuel burning equipment to prevent

back drafting. Follow the heating equipment manufacturer’s guideline and safety standards such as those published by the National Fire

Protection Association (NFPA), and the American Society for Heating, Refrigeration and Air Conditioning Engineers (ASHRAE), and the

local code authorities.

10.Not to be installed in a ceiling thermally insulated to a value greater than R40. (This is required for installation in Canada only).

BPT12-13H-M-05_28_20Page 1 of 3

When installing the ventilation fan in a , install new construction site

the main body of the fan and duct work during the rough‑in

construction of the building. The grill should be installed after the

finished ceiling is in place.

When installing in , use the dimensions shown existing construction

below to determine the required hole size for the ceiling.

Grill edges should overlap finished ceiling.

NOTE: If installing in existing construction, you must have access

to space above and below the installation location.

If you are replacing an existing fan, ensure that the new grill will

adequately cover the existing opening.

Do not install ventilation fan in areas where the duct work will require

configurations shown right.

PRE-INSTALLATION

BPT12-13H

(For bathroom size up to 75 ft

2

)

PRODUCT SPECIFICATIONS

MODELDUCT DIAMETERVOLTAGEHzPOWER CONSUMPTIONAIR DELIVERY @ 1” WG (CFM)NOISEWEIGHT

BPT12-13H

4”1206017 WATTS701 SONE8.0 LBS

DIMENSIONS

4” OUTLET

10.7”

6.7”

6.8”

0.74”

7.6”

Turning angle too sharpAvoid duct shrink

Too many elbowsElbow near the body

Fan

Body

Minimum 18”

9.4

9.4

Produktspezifikationen