Canarm SIS1010150 Bedienungsanleitung
Canarm
Dunstabzugshaube
SIS1010150
Lies die bedienungsanleitung für Canarm SIS1010150 (5 Seiten) kostenlos online; sie gehört zur Kategorie Dunstabzugshaube. Dieses Handbuch wurde von 3 Personen als hilfreich bewertet und erhielt im Schnitt 5.0 Sterne aus 2 Bewertungen. Hast du eine Frage zu Canarm SIS1010150 oder möchtest du andere Nutzer dieses Produkts befragen? Stelle eine Frage
Seite 1/5
SIS/SIG SERIES
SIDE INTAKE SUPPLY UNIT /
SIDE INTAKE GALVANIZED SUPPLY UNIT
OPERATION INSTRUCTIONS AND PARTS MANUAL
SIS SERIES MODELS: SIS-9, SIS-10, SIS-12, SIS-15, SIS-18, SIS-20
SIG SERIES MODEL: SIG-9, SIG-10, SIG-12, SIG-15
GENERAL SAFETY
Rotating parts, (pulleys, shafts and belts) on fans should not be exposed. Where these components are not protected by ductwork, cabinets
or covers, appropriate guards should be employed to restrict exposure to rotating parts. Access doors should not be opened with the fan
operating to avoid foreign objects being drawn into the system. On initial start-up, a careful inspection should be carried out to ensure no
foreign material is present which could become airborne in the system.
Read installation and operation instructions carefully before attempting to install, operate or service Canarm/Delhi SIS/SIG Series Blowers.
Failure to comply with instructions could result in personal injury and/or property damage. Retain instructions for future reference.
BEFORE YOU BEGIN
Inspect unit for damage, report any shipping damage to carrier. Check all fasteners, re-tighten as required. Rotate the blower wheel by
hand to ensure free rotation. If rubbing occurs, loosen the set screw(s), re-position the wheel to the shaft center, re-tighten set screws.
INSTALLATION
Remove hood and filters from inside the cabinet. Caulk top of curb before setting unit in place. (Curb must be smaller than unit “A”
dimension). Secure unit to curb through holes located around the bottom of the unit. Tighten wheel set screw.
A
A
F
F
G
D
BOTTO VI W
SIZE QUANTITY
SIS-9 24 3/8" 19 3/8" 10 1/4" 11 13/16" 6 9/32" 7 1/16" 7 1/16" 19 1/4" 16 9/16" 21 1/4" 16" x 24" x 1" 1
24"x 24" 70
SIS-10 28 3/8" 21 3/8" 11 3/8" 13 1/8" 7 5/8" 8 1/2" 8 1/2" 20 1/2" 18 9/16" 25 3/4" 15" x 20" x 1" 2
28"x 28" 87
SIS-12 32 3/8" 24 5/8" 13 7/16" 15 5/8" 8 3/8" 9 15/32" 9 15/32" 25 3/8" 21 9/16" 30 3/4"
20" x 25" x 1" &
16" x 25" x 1"
1 & 1 32"x 32" 117
SIS-15 36 3/8" 28 3/8" 15 7/8" 18 5/8" 8 7/8" 8" 12 1/2" 31 3/16" 25 13/16" 33 1/2" 20" x 28 1/2" x 1" 2
36"x 36" 175
SIS-18 36 3/8" 42 1/2" 18 7/8" 21 7/8" 7 1/4" 6 1/4" 11 1/4" 35 5/8" 32 11/16" 40 1/4"
20" x 25" x 1" &
16" x 25" x 1"
2 & 2 36"x 36" 262
SIS-20 44 3/8" 49" 24 3/4" 24 3/4" 9 13/16" 5 3/16" 14 7/16" 38 5/8" 35 9/16" 45 1/2"** 20" x 25" x 1" 6
44"x 44" 497
SIG-9 22" 24" 10 1/4" 11 7/8" 5" 3 7/8" 7 7/8" 16" 18 1/8" 19 7/8" 16" x 25" x 1" 1 21 7/8" x 21 7/8" TBA
SIG-10 22" 24" 11 7/8" 13 1/4" 4 7/16" 3 1/4" 6 7/8" 16" 18 1/8" 19 7/8" 16" x 25" x 1" 1 21 7/8" x 21 7/8" TBA
SIG-12 32" 32" 13 3/4" 15 7/8" 8 1/16" 4 1/4" 14" 25" 24 5/8" 25"
16" x 25" x 1" 2
31 7/8" x 31 7/8" TBA
SIG-15 32" 32" 16 1/8" 18 7/8" 6 9/16" 3" 12 7/8" 25" 24 5/8" 25" 16" x 25" x 1" 2 31 7/8" x 31 7/8" TBA
* Curb size to be smaller than inside cabinet to allow for flashing and roofing.
** Includes filter section
*INSIDE
CABINET
UNIT WEIGHT (LBS)
(without motors & drives)
SIG MODELS
SIS MODELS
G H L M Z
FILTERS
MODEL A B D E F
SIS_SIG-M-07_20_16 Page 1 of 5
AA
B
Z
L
R OV CAP FOR
FI T R ACC SS
2"
Ø5/16" OL S
FOR AST I G
TO CURB
MOTOR, PULLEYS & BELTS (See Table next page)
1. Mount the blower pulley on the blower shaft and tighten the set screw securely on the key of the shaft.
2. Mount the motor pulley on the motor shaft. Leave some clearance between the pulley and the motor end bell. Tighten the set screws
on the key of the motor shaft.
3. Install the motor on the motor platform using the hardware provided.
4. With the platform in its minimum position, install the V-belt within the pulley grooves. Position the motor on the motor platform to
ensure proper pulley alignment (see ) and secure to the motor platform. (A straight edge across the face of the driven pulleyFigure 1
should be parallel to the belt once proper alignment has been achieved).
Note: Adjustments in the variable speed pulley require pulley re-alignment.
SIS SERIES
SIG SERIES
5. Pivot the motor platform to tension the V-belt and lock in place using the 2 bolts on both sides of the blower. (Ideal belt tension
is the lowest tension at which the belt will not slip during start up.) As shown in illustration to right, a proper deflection of 1/64 of
the belt span is desired for belt tension.
5"
6" 7" " " " "8 9 10 12
82 1125 R4- PM
6 - PM -7 PM -6 PM 447-6 PM 4 - 4 PM 33-4 PM80 929 R 580 92 R 505 90 R 11 R 01 5 8 R 5 55 R
4L 4L 4L4 4L4 4L44 4L4 --37 39 1 2 5
4L 4L4 4L4 4L44 4L4 4L4 --39 1 2 6 7
4L4 4L44 4L4 4L4 4L4 4. --2 6 7 9 51
-- -- -- -- 4L 4L 4L55 57 60
-- -- -- -- 4L 4L 4L 459 60 6
M P ll yotor u e
C sta Iron
B o er u el w P ll y
C sta Iron
RPM
R eang
S S 9I -
S G 9I -
S S 10I -
S G 10I -
S S 12I -
S G 12I -
S S 15I -
S G 15I -
S S 18I -
S G 18I -
S S 20I -
BEL
T LEN THG
B S D OA E N
M T F AMEO OR R
H 4 T - B 7 1630 1232
B37 B39 B 34
-- -- --
H T - 4B57 1329 1005 B39 B 1 B44
-- -- --
H T - 4B67 1121 8 8 B40 B43 B46
-- -- --
H T - 4B77 969 733 B 2 B44 4B 8 B52 B56
--
H T 4 - 4B87 85 6 5 B43 B46 B49 B54B57
--
H T - 4B97 763 577 B 6 B48 B51 B56 B59
--
H T - 4B107 690 521 B 7 B50 B53 B58 B61
--
H T - 4 4B117 629 76 B 9 B51 B55 B59 B63
--
H T - 4B127 578 37
B51 B53 B55 B61 B64
--
H T - 4 4B137 535 0 B53 B55 B58 B63 B66
--
HB157T 466 352 B57 B59 B62 -
--
B70
--
H T - 4B187 390 295 B6 B65 B68
-- -- --
H TB77
756 568 - -- -- --
B51 B54
--
H TB87
667 500 - -- -- --
B53 B56
--
H TB97
596 7 - 44 -- -- --
B55 B58
--
H TB107
538 0 - 4 4 -- -- --
B56 B60
--
H TB117
4 - -- -- --91 368
B58 B61
--
H TB127
4 - -- -- --52 339
B60 B63
--
H TB137
4 - 18 314 -- -- --
B62 B65
--
H TB157
36 3724 - --
-- -- -- --B69
H T 4 - 4 -- -- -- -- --B87 85 6 5
B79
H TB97
763 577 - -- -- -- -- --
B81
H TB107
690 521 - -- -- -- -- --
B83
H TB117
629 76 - 4 -- -- -- -- --
B84
H TB127
578 37 - 4 -- -- -- -- --
B86
H TB137
535 0 - 4 4 -- -- -- -- --
B88
H TB157
4 - -- -- -- -- --66 352
B91
H TB187
390 295 - -- -- -- -- --
B97
H TB117
828 686 B86 - -- -- -- -- --
H TB127
756 618 B88 - -- -- -- -- --
H TB137
697 575 B90 - -- -- -- -- --
H TB157
616 509 - --
-- -- -- -- B93
12 2B.4 X
830 700 B90 - -- -- -- -- --
13 6 2B. X
759 631 B92 - -- -- -- -- --
F F A TI NAL HP APPLI N "4L" ELT MAY E TIT TE Y A IN " T THE PE IFIE " " ELT . Eg. ELT = 4LOR R C O CATIO S B S B SUBS U D B DD G 2 O S C D B B S B50 B 52
B O R ODL WE M EL
BELT LEN THG
B S D OA E N
M T F AMEO OR R
3 /4 A T I N L WE P LLEY - IAMETE PM AN E1 C S RO B O R U D R & R R G
4 FRAME8
56 FRAME
IVL44
O.D. 4. "15
S S 9 S G 9I - / I -
S S 10 S G 10I - / I -
S S 12 S G 12I - / I -
S S 15 S G 15I - / I -
S S 18 S G 18I - / I -
DOUB GROOLE VE
D 8600
O.D. "6
8550
O.D. . "5 35
213 215, T
FRAME
182 18, 4T FRAME
(DEDU T " FOR C 2
56 1 3 & 1 5, 4 , 4 T)
4 FRAME 8
(ADD " FOR 1 56
FRAME)
MODELS SIS- , 15
SIG- SIS- , 15 & 18
SIG- 18
13154 , 4 T FRAME
8325
O.D. . "3 25
1 3 & 1 54 T 4 T
FRAME
8 004
O.D. 4. "15
182 18, 4T FRAME
(DEDU T " FOR C 2
56 1 3 & 1 5, 4 , 4 T)
SIS/SIG SERIES
SIDE INTAKE SUPPLY UNIT / SIDE INTAKE GALVANIZED SUPPLY UNIT
SIS_SIG-M-07_20_16 Page 2 of 5
MOTOR, PULLEYS & BELTS (See Table below)
WARNING
EXCESSIVE BELT TENSION IS THE MOST FREQUENT CAUSE OF BEARING WEAR AND RESULTING NOISE.
PROPER BELT TENSION IS CRITICAL FOR QUIET EFFICIENT OPERATION.
Ideal belt tension is the lowest value under which belt slip will not occur at peak load conditions.
BELT ALIGNMENT
FIGURE 1
X X
ALX EXHAUSTER
WITH BASE HINGE & GREASE BOX
(PURCHASED SEPARATELY)
SIS / SIG SIDE INTAKE
SUPPLY UNIT
ROOF CURB AND CAP
(BY OTHERS)
DUCT EXTENSION SUPPORT
(BY OTHERS)
INTAKE DUCT EXTENSION
(BY OTHERS)
(,7+(5·
25·
40” MIN
18” MIN
FIGURE 2
FIGURE 3
TER
HOOD
C
O ERV
FI
T
IL
A
BINE
T
LO
WER
CA
BL
TER CAP
FIL
AKE OOD H
INT
ALLED.
INST
TA
Y
O
R
ACT
AILABLE
F
A
V
A
A
O
R & DRIVE
S
MOT
Y
.
AR
V
A
Y
PRODUCT MAACTUAL
PURPOSE.
Y
IS FOR DISPLAMODEL
BLOWER
FIGURE 4
FIGURE 5
INSTALLATION
REQUIREMENT
Typical configuration shall be a SIS/SIG air supply
unit, and an ALX spun aluminum roof exhauster.
ALX roof exhauster should have a base hinge and
a grease collector. BIRM utility blower is available
for high static pressure applications.
As shown in :Figure 3
• The bottom of the exhaust fan must be
18 inches away from the roof surface.
• The outlet of the exhaust fan must be
40 inches away from the roof surface minimum.
AND
• The inlet plane must be 10 feet away from the
outlet plane horizontally.
OR
• The inlet plane must be 3 feet away from the
outlet plane vertically.
HOOD AND FILTER INSTALLATION
(Models SIS/SIG-9 to SIS/SIG-15 & SIS-18)
Attach duct section when required (by others) to the SIS/SIG inlet flange. Drill 1/8” hole through duct and inlet flange and secure with
metal screws provided. Slide the hood (less filters) over the inlet flange and secure with the provided sheet metal screws.
HOOD/DUCT OVERLAP SHOULD NOT EXCEED 1”.
Remove hood cap and slide filter(s) into “U” channels located on the inner sides of the hood. Replace cap.
SIS/SIG SERIES
SIDE INTAKE SUPPLY UNIT / SIDE INTAKE GALVANIZED SUPPLY UNIT
SIS_SIG-M-07_20_16 Page 3 of 5
NFPA 96 TYPICAL
INSTALLATION
WHEEL ROTATION
Produktspezifikationen
| Marke: | Canarm |
| Kategorie: | Dunstabzugshaube |
| Modell: | SIS1010150 |
Brauchst du Hilfe?
Wenn Sie Hilfe mit Canarm SIS1010150 benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten
Bedienungsanleitung Dunstabzugshaube Canarm
21 August 2025
21 August 2025
21 August 2025
21 August 2025
21 August 2025
21 August 2025
21 August 2025
Bedienungsanleitung Dunstabzugshaube
- CENDO
- Kaiser
- Furrion
- Hisense
- Seiki
- Trade-Wind
- Gorenje
- Whirlpool
- Royal Catering
- Amica
- Oceanic
- Juno
- Schneider
- Hotpoint
- Sam Cook
Neueste Bedienungsanleitung für -Kategorien-
21 August 2025
21 August 2025
21 August 2025
21 August 2025
21 August 2025
21 August 2025
20 August 2025
20 August 2025
20 August 2025
20 August 2025