Crestron C2N-AMP-4X100 Bedienungsanleitung
Seiten 3 Schalten
Lies die Bedienungsanleitung für Crestron C2N-AMP-4X100 kostenlos online oder lade das PDF herunter. 24 Personen fanden diese Anleitung hilfreich. Frage zu diesem Modell? Stelle eine Frage
1
quickstart guide
C2N(I)-AMP-4X100
www.crestron.com
888.273.7876201.767.3400
Specifications subject to
change without notice.
C2N(I)-AMP-4X100
For Regulatory Compliance information, refer to the latest version
of Doc. 7289.
QUICKSTART DOC. 7288B (2032394, Sheet 1 of 2) 04.13
4 Room Audio System
1
Make the necessary connections as called out in the diagram below. Connect power last.
Hardware Hookup
NOTE: For triple the power (into 8 Ω speakers only), SPEAKER OUTPUTS 1
and 2 or SPEAKER OUTPUTS 3 and 4 can be bridged. For example, the left
speaker’s + and - terminals are connected to the two + terminals of output #1
and the right speaker’s + and - terminals are connected to the two + terminals
of output #2. Refer to the diagram to the right.
To adjust volume when bridged, select ROOM 1 for SPEAKER OUTPUTS 1
and 2 or select ROOM 2 for SPEAKER OUTPUTS 3 and 4.
RM 1
RM 3
RM 2
RM 4
BRIDGE
8 OHMS ONLY
+
-
+
-
L
+
-
+
-
R
L
+
-
+
-
R
To Cresnet Devices
NET
From AC Power Line
PWR
Tie to Ground
G
From Unbalanced Stereo Line Level Audio
Outputs from Source Devices
ANALOG SOURCES (IN)
To Additional Amplifiers
ANALOG SOURCES (OUT)
NOTE: The 24 volt lines on the NET ports of the amplifier are
limited to 300 mA.
To Loudspeakers
SPEAKER OUTPUTS
NON-BRIDGE
L
+
-
+
-
R
+-+-
LEFTRIGHT
NOTE: The C2NI-AMP-4X100 (International
version) requires a power cord that is
harmonized to the country’s national and local
electrical codes. Each inner wire in the cord
should be at least 18 AWG (0.75 mm
2
) and rated
for at least 300 V. The temperature rating of the
cord should be at least 60º C. The cord length
should be 1.5 - 2 meters.
To Cresnet
®
Devices
LOOP THRU
2
Attach the Labels
Use the included labels and inserts to prepare the C2N(I)-AMP-4X100:
1. Locate the SOURCE and ROOM label inserts included with the unit (SOURCE insert has space for six labels, ROOM insert has room for four labels).
2. Apply the peel-and-stick labels in the appropriate positions on the inserts, being careful to match label positions to what is configured in the programming software. For neatest appearance, when applying a label,
cover the white guidelines on the insert. First and last labels cover one line each; labels in between cover lines on their left and right sides.
Produktspezifikationen
| Marke: | Crestron |
| Kategorie: | Schalten |
| Modell: | C2N-AMP-4X100 |
Brauchst du Hilfe?
Wenn Sie Hilfe mit Crestron C2N-AMP-4X100 benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten
Bedienungsanleitung Schalten Crestron
Crestron DM-MD8X8-CPU3 Bedienungsanleitung Crestron DMC-4KZ-C Bedienungsanleitung Crestron C2NI-AMP-4X100 Bedienungsanleitung Crestron SWAMPI-24X8 Bedienungsanleitung Crestron DMC-4KZ-CO-HD Bedienungsanleitung Crestron DM-MD64X64 Bedienungsanleitung Crestron DMC-CATO-HD Bedienungsanleitung Crestron DMB-4K-I-C Bedienungsanleitung
Alle Crestron Schalten Bedienungsanleitungen
Beliebt in Schalten
Crestron HD-MD2X1-8K Bedienungsanleitung Crestron CNX-PAD8A Bedienungsanleitung Crestron DM-MD16X16-CPU3 Bedienungsanleitung
Bedienungsanleitung Schalten
Neueste Bedienungsanleitungen für Schalten
StarTech.com SV431DVIUDDM Bedienungsanleitung StarTech.com SV231DVIUDDM Bedienungsanleitung StarTech.com SV211KDVIEU Bedienungsanleitung StarTech.com SV231QDPU34K Bedienungsanleitung StarTech.com SV231DPU3A Bedienungsanleitung StarTech.com SV231 Bedienungsanleitung StarTech.com SV231TDVIUA Bedienungsanleitung StarTech.com SV431DPUA2 Bedienungsanleitung StarTech.com SV231DPU2 Bedienungsanleitung StarTech.com SV231MDPU2 Bedienungsanleitung