CRUX VIMPR-90P Bedienungsanleitung
CRUX
Nicht kategorisiert
VIMPR-90P
Lies die bedienungsanleitung für CRUX VIMPR-90P (3 Seiten) kostenlos online; sie gehört zur Kategorie Nicht kategorisiert. Dieses Handbuch wurde von 5 Personen als hilfreich bewertet und erhielt im Schnitt 4.4 Sterne aus 3 Bewertungen. Hast du eine Frage zu CRUX VIMPR-90P oder möchtest du andere Nutzer dieses Produkts befragen? Stelle eine Frage
Seite 1/3
PORSCHE
2017 911 2018 –
2017 718– 2018 Boxster / Cayman
20 2018 Cayenne 17 –
2017 18 –20 Macan
2017 – 2018 Panamera
- Retains functionality of Factory-installed Navigation System for passenger access at any time.
- Plug and Play Installation.
- Compatible with Porsche PCM4 and PCM4.1 Navigation radios.
- On some vehicles, the navigation will not work while the video- -motion function is active. This in
can only be detected by a test drive. Please see notes on page 3.
1 / 3
rev.121818
1. Remove the factory radio from the dashboard.
2. Remove the factory connectors from behind the factory radio.
3. Mate the T-Harness connections to the factory harness and radio. (Make sure all connectors are
properly seated into the interface and into the radio.)
4. Connect the 8-pin Molex connector from the T-harness to the VIMPR-90P module.
5. Set the DIP switches according to the table below.
6. Test the interface and re-install the radio into the dash.
Setting the DIP Switches of the VIMPR- P 90
Porsche
Dip 1
Dip 2
Dip 3
Dip 4
Dip 5
Dip 6
Video- -motion permanent in
ON
OFF
OFF
OFF
OFF
OFF
Video- -motion selective* in
OFF
OFF
OFF
OFF
OFF
OFF
*With DIP#1 set to OFF the included green wire is used to activate the video- -motion function. in
2 / 3
rev.121818
Note: DIP switch functions of the VIMPR- 90P
Dip 1 Activate Video In Motion –
Dip 2 no function –
Dip 3 no function –
Dip 4 no function –
Dip 5 CAN-bus termination resistor on the vehicle side –
Dip 6 CAN-bus termination resistor on the head-unit side –
NOTE: Vehicles with affected navigation performance
On some vehicles, the navigation performance is affected as long as the video- -motion function is in
activated. This can only be detected by a test drive and with DIP# set to ON. 1
If the navigation performance is affected you have to set DIP#1 to OFF. As long as the video- -motion in
function is activated, the navigation will NOT work. The green wire on the T-harness can be used to
activate the video- -motion function (Video- -motion selective) by connecting a switch (not included) in in
between the GREEN wire and +12V ACC.
Cable colour
Assignment
● Red
+12V Constant Pin 18
● Brown
Ground Pin 17
●● Orange/Violet
CAN HIGH Pin 6
●● Orange/Brown
CAN LOW Pin 12
ACTIVATING AND DEACTIVATING THE VIM FEATURE
The video- -motion can be activated and deactivated either by setting DIP# to ON (permanent VIM) in 1
or by the connecting a switch (not included) between the GREEN wire and +12V (selective VIM).
Video- -motion permanent in
With DIP#1 set to ON, the video- -motion function is activated permanently without disturbing the in
navigation performance.
Video- -motion selective in
With DIP# set to OFF, t GREEN wire is used to activate the video- -motion function. 1 he in
Connect a switch between the GREEN wire and +12V ACC.
● +12V = VIM is activated
● 0V VIM is deactivated=
3 / 3
rev.121818
Produktspezifikationen
| Marke: | CRUX |
| Kategorie: | Nicht kategorisiert |
| Modell: | VIMPR-90P |
Brauchst du Hilfe?
Wenn Sie Hilfe mit CRUX VIMPR-90P benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten
Bedienungsanleitung Nicht kategorisiert CRUX
9 Juni 2025
8 Juni 2025
8 Juni 2025
8 Juni 2025
8 Juni 2025
8 Juni 2025
8 Juni 2025
8 Juni 2025
8 Juni 2025
8 Juni 2025
Bedienungsanleitung Nicht kategorisiert
- VintageView
- The T.mix
- Plant Craft
- Ultron
- CommScope
- Shelly
- Airlux
- Atlantic
- Home Electric
- Aerotec
- Ankarsrum
- Kemo
- Astro
- EcoFlow
- Finnlo
Neueste Bedienungsanleitung für -Kategorien-
29 Juli 2025
29 Juli 2025
29 Juli 2025
29 Juli 2025
29 Juli 2025
29 Juli 2025
29 Juli 2025
29 Juli 2025
29 Juli 2025
29 Juli 2025