Electro Harmonix Nano Looper 360 Bedienungsanleitung
Electro Harmonix
Nicht kategorisiert
Nano Looper 360
Lies die bedienungsanleitung für Electro Harmonix Nano Looper 360 (4 Seiten) kostenlos online; sie gehört zur Kategorie Nicht kategorisiert. Dieses Handbuch wurde von 153 Personen als hilfreich bewertet und erhielt im Schnitt 5.0 Sterne aus 77 Bewertungen. Hast du eine Frage zu Electro Harmonix Nano Looper 360 oder möchtest du andere Nutzer dieses Produkts befragen? Stelle eine Frage
Seite 1/4
1
NANO LOOPER 360
Compact Looper
Congratulations on your purchase of the Nano Looper 360 The Nano Looper 360 is ! a
small, extremely easy to use looper with a total of -seconds of loop recording time. Not 360
only that, the available 360 seconds can be divided into 11 different Loops, so you get the
most out of the available memory! You can think of the Nano Looper 360 as your very own
“Loop Locker. ”
WARNING: Your Nano Looper 360 comes equipped with an Electro-Harmonix 9.6DC-
200BI power supply (same as used by Boss® & Ibanez®: 9.6 Volts DC 200mA). The Nano
Looper 360 requires 90mA at 9VDC with a center negative plug. Using the wrong adapter
or plug polarity may damage your unit and void the warranty.
– – FEATURES
- 6 minutes of loop recording time
- selectable independent Loops 11 , , that remain in memory until you erase them
- High quality uncompressed audio: -bit A/D/A, 44.1k Sample Rate , 24 Hz
- Intuitive looping interface
- Undo-Redo function
- Unlimited overdubbing
- Small pedal board footprint
- AC Adapter Included
- tionally may use 9V Alkaline Battery, battery life: approximately 4 hours of operation Op
(varies on conditions of use)
– – CONTROLS
LEVEL Knob – Controls the output level of the Loop. Your dry signal remains at unity
signal level from input to output. The dry signal also remains analog throughout the . 360
LOOP Knob Selects number: 1-11. When scrolling through loops, the –Loop MEM LED
flash quickly during transitions. If the loop has no recorded memory, the es MEM LED
remains off. If the loop has recorded memory, the remains and playback can MEM LED on
begin.
INPUT Jack Nano Looper 360. The input – This ¼” jack is the audio input for the
impedance is 2.2M .
OUTPUT Jack Nano Looper 360. The output – This ¼” jack is the audio output from the
impedance is 470.
9V Power Jack – Plug the output of the supplied AC adapter into the 9V power jack
located at the top of the Nano Looper 360. The Nano Looper 360 draws mA at 9VDC 90
with a center negative plug. The Nano Looper 360 accepts Boss® and Ibanez® style AC
Adapters.
2
– – QUICK START GUIDE
RECORDING A LOOP
1. To record a Loop; simply select an empty bank and press the once. The Footswitch
REC LED will light solid and recording begins immediately.
2. To stop recording the l press the again once. The will turn oop, Footswitch REC LED
off, the will turn on, and the loop will begin playing immediately. The PLAY LED
MEM LED will also light solid, indicating the presence of recorded loop memory.
3. All Loops play indefinitely. Each time the loop repeats, the will turn off PLAY LED
briefly.
4. After a loop is recorded, the length is subtracted from the total loop recording time.
5. Note: if the full 360 seconds of Loop Recording time is reached, recording will stop
automatically. The will turn off, the will turn on, and the Loop REC LED PLAY LED
will begin playing immediately. The will also light solid, indicating the MEM LED
presence of recorded l memory. oop
STOPPING & STARTING LOOP PLAYBACK
1. To stop loop playback, press the two times quickly. Footswitch
2. Note: REC LED the will turn on together with the during the first press. PLAY LED
Both LEDs turn off during the second press and playback stops immediately.
3. While stopped, press and release the Footswitch once to start playback. The PLAY
LED will light indicating the loop is playing.
RECORDING AN OVERDUB
1. To record an overdub, make sure a L is playing back. If a loop is not playingoop ,
press the once to begin playback. The will turn on and the Footswitch PLAY LED
loop will begin playing immediately.
2. To start recording an overdub, press the once. The will turn Footswitch REC LED
on, together with the , and audio will be recorded on top of the original PLAY LED
loop. No volume loss will occur to the previously recorded portion of the loop.
3. To stop overdubbing the loop; press the again once. The will Footswitch REC LED
turn off, and the loop will continue playing along with the overdubbed audio.
4. Overdubbing will never change the length of the loop.
5. If the loop repeats during overdubbing, the and will both turn REC LED PLAY LED
off briefly. The Nano Looper 360 can overdub indefinitely, allowing you to
continuously overdub new audio onto your loop.
6. After finishing an Overdub, the UNDO-REDO function is enabled. You may undo,
then redo the last Overdub as many times as you like.
UNDO-REDO FUNCTION
1. The Undo/Redo function can only be initiated while a loop is playing back. Undo/Redo
cannot be performed during Overdub, Record or Stop modes.
2. To undo an overdub (remove the last take) during l playback, press and hold the oop
Footswitch for 1-second. The PLAY LED will blink twice and the previous overdub
will be removed.
3. To redo an overdub (restore the last take) during l playback, press and hold the oop
Footswitch for 1-second. The PLAY LED will blink twice and the previous overdub
will be restored.
3
4. Note: once UNDO-REDO is enabled, this function is available until the loop is erased.
This is true even if returning to a loop from a previous selection, or even after power
cycling.
ERASING A LOOP
1. To erase a loop, play-back must be stopped. If a loop is playing, press the
Footswitch two times quickly.
2. Press and hold the for 2 seconds. The will blink six times then Footswitch MEM LED
remain off, indicating the loop is erased.
3. Note: the ERASE function is only enabled when the loop has recorded memory, as
indicated by the remaining lit. MEM LED
LOOP MEMORY
1. Any recorded audio is stored automatically to the Nano Looper 360’s internal memory.
2. All recorded loops will remain in memory until they are erased. Power cycling does not
erase loops unless power is cut while recording the loop. Any loop or overdub that
was being recorded at the time of power loss will not be saved by the 360.
3. After loop is recorded, the length is subtracted from the total l recording time. a oop
For example, if a 60 second loop is recorded on Loop 1, there are 300 seconds still
available for Loops 2-11. Overdubbing on top of any given loop does not subtract
from total loop recording time.
4. When the full 360-seconds loop recording time depleted, recording a of is new loop
is inhibited. If an empty Loop is selected and recording is attempted, the MEM-LED
will blink twice. To free-up recording memory, select a loop with recorded memory
and erase it.
FACTORY RESTORE
1. To initialize a Factory Restore, unplug the power jack.
2. Set the Loop Knob to Loop 11.
3. Plug in the power jack while down the footswitch until all three LEDs begin to holding
flash, this takes about 2 seconds. Factory restore will not begin until all three LEDs
are blinking. If you change your mind before the three LEDs begin to blink, release
the footswitch or move the LOOP knob to another loop location other than 11.
4. Once all three LEDs start blinking you can release the footswitch. All three LEDs will
continue to flash until the Factory Restore process is complete (~4 seconds). After the
process is complete, the MEM LED will flash quickly and Loop 11 will be selected.
5. Note: All Loop audio is erased during Factory Restore, and the process cannot be
undone.
– – CHANGING THE BATTERY
To change the 9-volt battery, you must remove the 4 screws on the bottom of the Nano
Looper 360. Once the screws are removed, you can take off the bottom plate and change
the battery. Please do not touch the circuit board while the bottom plate is off or you risk
damaging a component.
Battery life is icated by the three LEDs. These LEDs will fail to turn-on with a dead ind
battery. If the 360 fully discharges a battery during normal operation, all LEDs will turn-off
and prevent all functions. The battery must be changed immediately.
Produktspezifikationen
| Marke: | Electro Harmonix |
| Kategorie: | Nicht kategorisiert |
| Modell: | Nano Looper 360 |
Brauchst du Hilfe?
Wenn Sie Hilfe mit Electro Harmonix Nano Looper 360 benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten
Bedienungsanleitung Nicht kategorisiert Electro Harmonix
5 September 2024
5 September 2024
5 September 2024
4 September 2024
4 September 2024
3 September 2024
Electro Harmonix Germanium 4 Big Muff Pi Bedienungsanleitung
3 September 2024
3 September 2024
Electro Harmonix Deluxe Memory Man 550-TT Bedienungsanleitung
3 September 2024
28 August 2024
Bedienungsanleitung Nicht kategorisiert
- Florabest
- Woodland Scenics
- Umarex
- Vox
- Start International
- AeroCool
- Wavtech
- Kärcher
- D-Jix
- Commercial Chef
- Heylo
- ESYLUX
- Ambiano
- Digigram
- Wolf Garten
Neueste Bedienungsanleitung für -Kategorien-
15 Juni 2025
15 Juni 2025
15 Juni 2025
15 Juni 2025
15 Juni 2025
15 Juni 2025
15 Juni 2025
15 Juni 2025
15 Juni 2025
15 Juni 2025