Extech DV50 Bedienungsanleitung
Lies die bedienungsanleitung für Extech DV50 (1 Seiten) kostenlos online; sie gehört zur Kategorie Messung. Dieses Handbuch wurde von 15 Personen als hilfreich bewertet und erhielt im Schnitt 4.2 Sterne aus 8 Bewertungen. Hast du eine Frage zu Extech DV50 oder möchtest du andere Nutzer dieses Produkts befragen? Stelle eine Frage
Seite 1/1
DV50-EU-EN v2.1 08/13
User’s Guide
DV50 Non-Contact Voltage Detector
Safety
WARNING: Risk of Electrocution. Before use, always test the Voltage
Detector on a known live circuit to verify proper operation
WARNING: Risk of Electrocution. Keep hands and fingers on the
handle of the probe and away from the probe tip
WARNING: If the equipment is used in manner not specified by
manufacturer, the protection provided by the equipment may be
impaired
CAUTION: Read, understand and follow Safety Rules and Operating
Instructions in this manual before using this product.
Do not attempt to repair this unit. There are no user serviceable parts.
Do not expose the unit to extreme temperatures or high humidity
Do not use the unit if it is wet or damaged
Do not apply more than the rated voltage between the probe tip and
ground.
Do not operate with the case open
This symbol, adjacent to another symbol or terminal, indicates
the user the user must refer to the manual for further
information.
This symbol, adjacent to a terminal, indicates that, under normal
use, hazardous voltages may be present
Double insulation
Specifications
Voltage Sensitivity 6V to 1000V AC
Bandwidth 50/60Hz
Operating Temperature 32 to 122
o
F (0 to 50
o
C)
Storage Temperature -4 to 140
o
F (-20 to 60
o
C)
Altitude Operating below 2000 meters
Relative Humidity 80% up to 31
o
C, decreasing to 50% at 50
o
C
Battery 2 x 1.5V button batteries (LR44/AG13)
Dimensions/Weight 7.7x2.4x1.2”(195x62x30mm)/ 5.2oz (148g)
Safety For indoor use and in accordance with
Overvoltage Category IV 600V, Overvoltage
Category III 1000V, Pollution Degree 2.
Description
1. Voltage sensor
2. ON and Voltage indicator lights
3. Sensitivity adjustment (rear)
4. ON/OFF switch
5. Battery compartment
6. Telescoping rod
7. Probe storage area
8. Handle
Operating Instructions
AC VOLTAGE DETECTION
1. Lift the probe tip from the storage area and extend the
telescoping rod.
2. Twist the rod into the LOCKED position as indicated.
3. Slide the ON/OFF switch to the ON position. The green ON light
will illuminate and the red detection light may flash.
4. Adjust (decrease) the sensitivity adjustment until the red flashing
voltage indicator light and the beeper just stop.
5. Place the probe tip on the wire or object to be tested. If voltage is
present the red flashing light and beeper will continuously alert.
6. To turn off the audible beeper, slide the ON/OFF switch to the
position.
NOTE: RF signals in close proximity to the detector may cause the light
and beeper to latch into a constant tone and light indication. Wait until
the RF signal has disappeared before proceeding with detection.
NOTE: The conductors in electrical cord sets are often twisted. For
best results, rub the probe tip along a length of the cord to assure
placing the tip in close proximity to the live conductor.
NOTE: The detector is designed with high sensitivity. Static electricity
or other sources of energy may randomly trip the sensor. This is normal
operation.
Battery Installation
1. Unscrew the probe tip..
2. Insert two 1.5V button batteries (observe polarity).
NOTE: If your meter does not work properly, check the battery to make
sure that it still good and that it is properly inserted.
You, as the end user, are legally bound (Battery
ordinance) to return all used batteries and accumulators;
disposal in the household garbage is prohibited!
You can hand over your used batteries / accumulators,
gratuitously, at the collection points for our branches in
your community or wherever batteries / accumulators
are sold!
Disposal
Follow the valid legal stipulations in respect of the
disposal of the device at the end of its lifecycle
Copyright ©2013FLIRSystems,Inc.
Allrights rightreservedincludingthe ofreproductioninwholeorin inpart any
form
ISO‐9001Certified
www.extech.com
Produktspezifikationen
| Marke: | Extech |
| Kategorie: | Messung |
| Modell: | DV50 |
Brauchst du Hilfe?
Wenn Sie Hilfe mit Extech DV50 benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten
Bedienungsanleitung Messung Extech
5 Januar 2026
5 Januar 2026
4 Januar 2026
4 Januar 2026
4 Januar 2026
8 Dezember 2025
8 Dezember 2025
8 Dezember 2025
8 Dezember 2025
7 Dezember 2025
Bedienungsanleitung Messung
- Be Cool
- Rigel Medical
- Westfalia
- Joy-it
- König
- FLIR
- AS Schwabe
- Condtrol
- Dostmann Electronic
- Camille Bauer
- GMW
- Beurer
- Workzone
- Orium
- Steinberg
Neueste Bedienungsanleitung für -Kategorien-
20 Januar 2026
20 Januar 2026
20 Januar 2026
20 Januar 2026
20 Januar 2026
19 Januar 2026
19 Januar 2026
19 Januar 2026
19 Januar 2026
18 Januar 2026